On sale

1 2 3
Newest Items First
96 Per Page
-15%
MOSFET Power Controller
$12.50 $14.75  
2 pc(s)
MOSFETs are awesome. They're like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also has sewable pads so you can use it in e-textile projects that need more juice....
− +
-5%
Type 2 NFC Card - NTAG216
$2.85 $3.00  
53 pc(s)
A white plastic PVC card that has an NTAG216 chip embedded inside. About the size of a credit card, this is a blank white NFC card that you can use with a card printer to customize. It houses an NTAG216 chip which holds up to 888 bytes of memory. Documents : Datasheet (NTAG216)...
− +
-50%
Solar Panel - 18V 2.5W
$18.75 $37.50  
2 pc(s)
Need a clean energy source to power you project? Check out this high quality, high output solar panel. Each panel features high efficient polycrystalline cells mounted onto a fibreglass PCB and covered with epoxy resin which protect the cells without reducing efficiency. A weatherproof plastic...
− +
-20%
Servo - Generic Metal Gear (Micro Size)
$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...
− +
-15%
CAN-BUS Shield
$38.25 $45.00  
1 pc(s)
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output...
− +
-55%
3DR Safety Switch for PX4 / Pixhawk
$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...
− +
-50%
3DR Buzzer for PX4 / Pixhawk
$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +
-20%
MP3 Trigger
$60.00 $75.00  
1 pc(s)
Make some noise with your next project! The MP3 Trigger board is built to make it MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control,...
− +
-50%
Thermally Conductive Adhesive
$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...
− +
-20%
Resistor Kit - 1/4W 1% (600 total)
$6.40 $8.00  
9 pc(s)
Don't you hate it when you're in the middle of a build and you don't have a certain value of resistor? Don't let it happen again with this resistor kit. This kit contains a resistor color code chart and 20 each of 30 standard value 1/4 Watts resistors with 1% tolerance. It's perfect for starting...
− +
-20%
3.5" Resistive Touchscreen LCD + Pre-configured 16GB microSD Card For RaspberryPi
$37.60 $47.00  
7 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 3.5 inches 480x320 high resolution LCD display with resistive touchscreen, engineered specifically to let you quickly attached the...
− +
-20%
LilyPad LED White (5pcs)
$4.75 $5.95  
Out-of-stock
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
Out-of-stock
-8%
LilyPad Arduino 328 Main Board
$22.95 $24.95  
1 pc(s)
The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package designed to minimize snagging and profile,...
− +
-10%
Big Easy Stepper Motor Driver
$31.50 $35.00  
1 pc(s)
The Big Easy Driver, designed by Brian Schmalz , is a stepper motor driver board for bi-polar stepper motors up to 2A/phase. It is based on the Allegro A4983 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
-30%
3 Way Spring Clamp Terminal Block (Pack of 3)
$0.95 $1.35  
126 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
-29%
7mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 7mm Documents : Datasheet
− +
-29%
10mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
22 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 10mm Documents : Datasheet
− +
-29%
12mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet
− +
-29%
12mm Panel Mount Momentary Pushbutton - Green
$0.60 $0.85  
6 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Red)
$0.60 $0.75  
5 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including...
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Green)
$0.60 $0.75  
38 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1.5A@250VAC. Overall length (including...
− +
-33%
Panel Mount Pushbutton - Latching (10mm, Red)
$0.50 $0.75  
28 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
-20%
Load Cell - 10kg, Straight Bar
$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 20kg, Straight Bar
$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 5kg, Straight Bar
$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock
-20%
Load Cell - 1kg, Straight Bar
$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-50%
Capacitor Kit (300 Total)
$3.95 $7.90  
18 pc(s)
Our new capacitor kit comes with 10 each of 30 different capacitance values. All of these capacitors are packed into the zip-lock bags. This kit provides an easy way to build up a catalog of commonly used capacitors in a way that keeps them organised. Includes : Ceramic...
− +
-20%
Vibration Motor - 10x3.15mm
$2.00 $2.50  
46 pc(s)
This itty-bitty, shaftless vibratory motor is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. All moving parts are protected within the housing. With a 2.6-3.6V operating range, these units shake crazily at 3V. Once...
− +
-31%
LilyPad Reed Switch
$5.50 $7.95  
1 pc(s)
The LilyPad Reed Switch is a simple breakout for a reed switch that will make it easy to use in e-textiles circuits in exactly the same manner that you can currently use the LilyPad Button and Switch. In order to make it more durable for wearable use, we've used a different style of reed switch,...
− +
-37%
Jumper Wire Kit
$2.50 $3.95  
1 pc(s)
This is a time saving kit of jumper wires - cut, stripped, and pre-bent for your prototyping pleasure. Included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each.
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Adjustable Focus Lens
$39.00 $48.75  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Fisheye Lens
$48.00 $60.00  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
-20%
2 x AAA Battery Holder
$0.80 $1.00  
7 pc(s)
Battery holder for two AAA batteries, terminated with ~150mm leads
− +
-50%
3 x AA Battery Holder
$0.50 $1.00  
84 pc(s)
Battery holder for three AA batteries, terminated with ~150mm leads
− +
-33%
Rocker Switch - SPST Medium
$0.60 $0.90  
2 pc(s)
This switch is about the same size as our Rocker Switch -DPDT except that it's single-pole single-throw. It's rated for 6A@250V / 10A@125VAC and can be snap-in panel mounted. Documents : Dimensional Drawings
− +
-10%
9V Battery Holder with On/Off Switch
$1.80 $2.00  
6 pc(s)
Enclosed battery holder for 9V battery. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-17%
4 x AA Battery Holder
$1.00 $1.20  
23 pc(s)
Battery holder for four AA batteries, terminated with ~150mm leads
− +
-50%
3 x AA Battery Holder with Switch and Cover
$1.00 $2.00  
1 pc(s)
Enclosed battery holder for three AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-20%
2 x AA Battery Holder
$0.80 $1.00  
Out-of-stock
Battery holder for two AA batteries, terminated with ~150mm leads
Out-of-stock
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
-20%
microSD Shield
$19.60 $24.50  
1 pc(s)
Running out of memory space in your Arduino project? The SparkFun microSD Shield equips your Arduino with mass-storage capability, so you can use it for data-logging or other related projects. Communication with microSD cards is achieved over an SPI interface. The SCK, DI, and DO pins of the...
− +
-33%
RCA Video Cable - 6'
$3.00 $4.50  
1 pc(s)
RCA cables are super handy for moving analog signals around. This is a great way to connect a composite video capable device, like the Raspberry Pi, to a suitable display. They also come in handy if you want to hook up your old-school analog gaming consoles, you know it's always impossible to...
− +
-31%
Push Button 33mm - Pink
$1.80 $2.60  
26 pc(s)
This is a 33mm round momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. Features : Convex Button 35.75 mm Diameter x 46 mm Height M28 thread Mounting Hole Diameter: 27.3 mm Net weight: 0.015kg Rated...
− +
-50%
LilyPad SimpleSnap Protoboard
$6.00 $12.00  
3 pc(s)
The LilyPad SimpleSnap Protoboard is a new, easy way to create e-textiles projects with LilyPad that are modular and can be disassembled or broken down, it's also a great way to prototype! The SimpleSnap Protoboard is made to connect to the SimpleSnap main board so that the board is...
− +
-20%
LilyPad Simple Power
$13.55 $16.95  
Out-of-stock
The LilyPad Simple Power is a simple e-textile board that lets you connect and charge a lipo battery and switch it on or off, that’s it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no...
Out-of-stock
-33%
Vibration Motor 11.6×4.6×4.8mm
$3.95 $5.90  
4 pc(s)
This tiny DC motor produces vibrations by spinning an eccentric shaft at over 10,000 RPM when powered at 3 V. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback, and its small size (11.6 × 4.6 × 4.8 mm) and light weight (0.8 g) make it...
− +
-50%
Teensy SmartMatrix Shield Kit for RGB LED Panel
$12.45 $24.90  
12 pc(s)
The SmartMatrix Shield is the best way to connect the Teensy 3.2 to Large RGB LED matrix display panels . The shield makes it easy to connect the 13 signals required to drive the display, connects an external 5V supply to power the display and Teensy, and brings out the Teensy's free...
− +
-20%
PicoBoard
$55.20 $69.00  
1 pc(s)
The PicoBoard allows you to create interactions with various sensors. Using the Scratch programming language, you can easily create simple interactive programs based on the input from sensors. The PicoBoard incorporates a light sensor, sound sensor, a button and a slider, as well as 4...
− +
-31%
Panel Mount Toggle Switch - SPDT
$0.55 $0.80  
5 pc(s)
This heavy duty single-pole, double-throw (SPDT) toggle switch makes a great power switch or state selector for user interface. Rated for 6A at 125VAC. Includes a two threaded nuts and washer for mounting.
− +
-35%
Bare Conductive - Electric Paint (50ml)
$27.95 $43.00  
3 pc(s)
Bare Conductive's Electric Paint is just like any other water-based paint... except that it's electrically conductive! This means that you can actually paint wires onto things like models, clothes, furniture, walls, almost anything you can think of. Standard acrylic or water-based paints can...
− +
-29%
Tactile Button Assortment Pack of 12
$6.50 $9.10  
19 pc(s)
These tactile buttons are great for all sorts of projects. This assortment comes with 2 of each of 6 different colors for a total of 12 buttons. The colored caps are removable and the buttons fit into breadboards. See the drawing below for exact dimensions. Documents: Drawing
− +
-11%
Non-Invasive Current Sensor - 30A
$15.50 $17.50  
1 pc(s)
This non-invasive current sensor (also known as a “split core current transformer”) can be clamped around the supply line of an electrical load to tell you how much current is passing through it. It does this by acting as an inductor and responding to the magnetic field around a...
− +
-40%
0.1" (2.54mm) Crimp Connector Housing: 1x40-Pin
$0.60 $1.00  
337 pc(s)
These housings work with our crimp pins to let you quickly make custom cables that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards . Specifications : Pins: 1 x 40 Spacing: 0.1 in (2.54mm)
− +
-31%
Push Button 33mm - Green
$1.80 $2.60  
20 pc(s)
This is a 33mm round momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. Features : Convex Button 35.75 mm Diameter x 46 mm Height M28 thread Mounting Hole Diameter: 27.3 mm Net weight: 0.015kg Rated...
− +
-31%
Push Button 33mm - Yellow
$1.80 $2.60  
28 pc(s)
This is a 33mm round momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. Features : Convex Button 35.75 mm Diameter x 46 mm Height M28 thread Mounting Hole Diameter: 27.3 mm Net weight: 0.015kg...
− +
-7%
RGB LED Matrix Panel - 32x32
$69.95 $75.00  
1 pc(s)
Are you looking to add a lot of color to your project? These massive 32x32 RGB LED panels are an awesome place to start. You can create animations, games, or all sorts of other fun displays with them. Yes, you read that right: a 32x32 LED matrix, that's 1024 LEDs on a 7.5" x 7.5" board. On...
− +
-33%
Rocker Switch - DPDT
$0.60 $0.90  
34 pc(s)
This switch is about the same size as our right angle rocker switch except that it's double-pole double-throw. It's rated for 10 Amps at 125VAC and can be snap-in panel mounted. Documents : Dimensional Drawings
− +
-20%
RedBot - Robotic Development Platform
$39.95 $49.95  
6 pc(s)
The RedBot Mainboard is a robotic development platform that works with the Arduino IDE. The RedBot is a motor driver and Ardiuno combination with various headers and connections, eliminating the need to stack multiple shields. By using the RedBot accessory boards and your own chassis, you...
− +
-20%
LilyPad LED Yellow (5pcs)
$4.75 $5.95  
7 pc(s)
This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-50%
IOIO and Breadboard Holder
$2.60 $5.20  
1 pc(s)
This holder allows you to safely secure a IOIO development board and a self-adhesive breadboard in place to easily run jumper wires in between the two to form simple or complex prototyping circuits. Unlike it’s cousin, for the Arduino, this IOIO and breadboard holder has been made specifically...
− +
-15%
SPDT Mini Power Switch
$1.95 $2.30  
19 pc(s)
Simple SPDT slide switch. Rated at 30V/200mA. The pins have .1" spacing - fits great into a breadboard! Use it as a power switch or general control switch. Documents : Dimensional Drawing
− +
-20%
LilyPad LED Pink (5pcs)
$4.75 $5.95  
7 pc(s)
Here is a simple 5 pack of pink LEDs for LilyPad, or whatever else you can dream up. Light up the night! LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting...
− +
-20%
WiFi Module - ESP8266 1MB Flash
$7.95 $9.95  
56 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...
− +
-7%
ISL29125 RGB Light Sensor
$12.50 $13.50  
2 pc(s)
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity...
− +
-42%
AutoDriver - Stepper Motor Driver
$29.50 $51.00  
1 pc(s)
This AutoDriver makes it easy to put the L6470 Stepper Driver (a.k.a "dSPIN") to work in your project. Simply connect your motors and your SPI-capable microcontroller and get steppin'! STMicro's L6470 is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent...
− +
-26%
Thermistor 10K
$1.00 $1.35  
11 pc(s)
10K thermistor with a negative temperature coefficient. Good choice for temp-sensing aplications. Vishay part #: NTCLE100E3103JB0 Note: You get only one thermistor. Document: Datasheet
− +
-40%
Mini Thermal Printer
$45.00 $75.00  
1 pc(s)
This is a thermal printer like you would find on a cash register or adding machine. It will print simple strings passed to it via TTL serial, bitmap images (poorly) and it even generates several different formats of barcodes! The thermal printer takes 57mm wide thermal paper with a...
− +
-48%
Fio v3 - ATmega32U4
$29.50 $56.90  
1 pc(s)
The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4. While the Fio v3 is not yet compatible with the Arduino v1.0 IDE, it's still a very capable XBee-ready development board. The JST-connector and 3.3v system voltage make this a great development tool for...
− +
-30%
Basic 8x2 Character LCD - Black on Green 5V
$7.00 $9.95  
3 pc(s)
This is a basic 8 character by 2 line display with black text on green background. The screen utilizes the extremely common HD44780 parallel interface chipset. Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes LED backlight....
− +
-6%
USB Type A Female Breakout
$6.50 $6.95  
1 pc(s)
This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you. Dimensions : 1.02 x 0.9" (26.06 x 22.93mm)...
− +
-7%
RF Link Receiver - 4800bps (434MHz)
$8.50 $9.10  
2 pc(s)
These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
-20%
RF Link Receiver - 4800bps (315MHz)
$7.25 $9.10  
6 pc(s)
These wireless receivers work with our 315MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
-20%
RF Link Transmitter - 315MHz
$6.30 $7.90  
4 pc(s)
These wireless receivers work with our 315MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
-40%
Serial Enabled 16x2 LCD - White on Blue 5V
$19.95 $33.20  
5 pc(s)
The serial enabled LCD allows you to control a parallel based LCD over a single-wire serial interface. Included in this product is a white on blue 16x2 LCD connected to our serial backpack. The backpack, based around a PIC16LF88, takes a TTL serial input and prints the characters it receives...
− +
-40%
Serial Enabled 20x4 LCD - Black on Green 5V
$22.75 $37.85  
1 pc(s)
The serial enabled LCD allows you to control a parallel based LCD over a single-wire serial interface. Included in this product is a black on green 20x4 LCD connected to our serial backpack. The backpack, based around a PIC16F88, takes a TTL serial input and prints the characters it receives...
− +
-20%
Hakko Soldering Iron - 40W 230V EU Plug
$9.95 $12.50  
37 pc(s)
This is a simple fixed temperature, quick heating soldering iron from Hakko. It is not as powerful as soldering station such as Hakko FX-888, but if you really need a low cost iron for your tool box, this lovely iron is a good choice. At 40W, this iron is perfect for kit building or minor...
− +
-20%
4 x AA Battery Holder with Barrel Jack
$1.20 $1.50  
36 pc(s)
This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino Uno (among a number of other products) allowing you to easily make your project...
− +
-20%
Small Stepper Motor
$11.60 $14.50  
1 pc(s)
These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. Features : Stride Angle (degrees) : 7.5 2-Phase Rated Voltage : 12V Rated Current : 400mA 3mm Diameter Drive Shaft...
− +
-71%
USB Weather Board
$50.00 $175.00  
2 pc(s)
Got weather? This board can handle it. The USB Weather Board includes onboard sensors for barometric pressure, humidity, temperature, and light level. We've also added headers in the new version so you can connect the board to the weather meters (not included), adding sensors for wind...
− +
-21%
Tweezers - Straight (ESD Safe)
$5.00 $6.30  
1 pc(s)
These are nice, solid curved tweezers. They have a very fine tip which allows you to pick up very small parts with precision. This is a great tool to have if you're working with surface mount components or anything with very small parts. The ESD-safe coating will also help prevent...
− +
-50%
Flash Memory - microSD 1GB
$4.50 $9.00  
78 pc(s)
This is a 1 GB microSD media card. Perfect for massive datalogging in a minute amount of space. These microSD cards have a simple to use SPI interface allowing any micro to read and write data in a very large 1 gigabyte storage array. This product is guaranteed to work in products that use a...
− +
-10%
Solder Lead Free - 100-gram Spool
$12.50 $13.95  
1 pc(s)
This is your basic spool of lead free solder with a water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced users that should last 6-12 months depending on how often you solder. If you are just beginning to solder, we recommend you order the...
− +
-50%
Bluetooth Module Breakout - Roving Networks (RN-41 v6.15)
$27.50 $55.00  
1 pc(s)
This is a simple breakout for the Roving Networks Bluetooth module. All pertinent pins are broken out and labeled. This new version's headers are unpopulated. Check below for appropriate headers. The module from Roving Networks is powerful, small, and very easy to use. This...
− +
-50%
9V Battery Snap to 2.1mm Barrel Jack Adapter
$0.90 $1.80  
75 pc(s)
This 9V Snap to 2.1mm Barrel Jack Adapter provides the ability to conveniently use a 9V battery to power many common boards and modules such as the popular Arduino and compatible microcontrollers. This plug is a common barrel type with an outside diameter of 5.5mm and an inside diameter of...
− +
-31%
Tilt Sensor
$2.20 $3.20  
12 pc(s)
This basic tilt switch can easily be used to detect orientation. Inside the can are a pair of balls that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors,...
− +
-50%
Break Away Headers - Right Angle
$1.00 $2.00  
1218 pc(s)
A row of right angle headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers.
− +
-30%
Potentiometer 10K with Knob
$0.95 $1.35  
587 pc(s)
There are lots of potentiometer out there. Some are very large, some so small they require a screwdriver. This 10K potentiometer has a small knob built right in and it's breadboard friendly to boot! Perfect for your next LCD contrast adjuster, opamp setting, or volume level. This model # is...
− +
-11%
FTDI Basic Breakout - 3.3V
$23.95 $26.85  
3 pc(s)
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out...
− +
-20%
MEMS Microphone Breakout - INMP401 (ADMP401)
$12.80 $16.00  
1 pc(s)
This tiny breakout board features the ADMP401 MEMs microphone. One of the key advantages to this breakout and microphone is the bottom ported input. This means the microphone's input can fit flush against the enclosure of your project. Plus you will not have to deal with trying to solder the...
− +
-20%
Sparkfun XBee Wireless Shield
$19.95 $24.95  
1 pc(s)
Xbee radios are an awesome way to add wireless capability to your Arduino project and now it's even easier with the XBee Shield. The shield form-factor mates directly with any dev board that has an Arduino standard footprint and equips it with wireless communication capabilities using the...
− +
-50%
LilyPad Protoboard Large
$4.75 $9.50  
1 pc(s)
This is a large board for prototyping through hole components with the LilyPad system. There are an array of pins all shorted together with 10mil traces. This allows for quick and easy prototyping - all you have to do is cut the traces between holes you don't want connected! Standard 0.1"...
− +
-25%
LilyPad Slide Switch
$2.95 $3.95  
2 pc(s)
This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to...
− +
-30%
Force Sensitive Resistor - Small (FSR400) - Male Pin Header
$6.30 $9.00  
61 pc(s)
This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR,...
− +
-33%
Screw Terminals 5mm Pitch (2-Pin)
$0.50 $0.75  
53 pc(s)
Screw Terminals with 5mm pitch pins. Comes in 2 positions and have the really cool feature of slide-locking together to form any size you need (4, 6, up to 20 without problems). Rated up to 300V @ 8A. Terminal can accept 26 to 14AWG wire. 5mm/197mil pin pitch will line up well with standard...
− +
1 2 3