On sale

1 2 3 4 5
Sort Alphabetically: A to Z
48 Per Page
-11%
Educational Traffic Light Module
$1.20 $1.35  
3 pc(s)
The Educational Traffic Light Module is a low cost hardware module designed to allow users to take their first steps into interfacing microcontroller with the real world. It is designed to remove many of the common hurdles people are faced with when getting started using hardware with the...
− +
-20%
Electric Paint Lamp Kit
$48.00 $60.00  
6 pc(s)
Make three paper lamps with no tools, no programming, no special skills required. A great gift for anyone that needs more light in their life! Transform a piece of paper into a beautiful lamp in three easy steps. Paint, plug, and play! Use this Electric Paint to create custom...
− +
-48%
Fio v3 - ATmega32U4
$29.50 $56.90  
1 pc(s)
The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4. While the Fio v3 is not yet compatible with the Arduino v1.0 IDE, it's still a very capable XBee-ready development board. The JST-connector and 3.3v system voltage make this a great development tool for...
− +
-50%
Flash Memory - microSD 1GB
$4.50 $9.00  
78 pc(s)
This is a 1 GB microSD media card. Perfect for massive datalogging in a minute amount of space. These microSD cards have a simple to use SPI interface allowing any micro to read and write data in a very large 1 gigabyte storage array. This product is guaranteed to work in products that use a...
− +
-30%
Force Sensitive Resistor - Small (FSR400) - Male Pin Header
$6.30 $9.00  
61 pc(s)
This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR,...
− +
-11%
FTDI Basic Breakout - 3.3V
$23.95 $26.85  
3 pc(s)
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out...
− +
-20%
Hakko Soldering Iron - 40W 230V EU Plug
$9.95 $12.50  
37 pc(s)
This is a simple fixed temperature, quick heating soldering iron from Hakko. It is not as powerful as soldering station such as Hakko FX-888, but if you really need a low cost iron for your tool box, this lovely iron is a good choice. At 40W, this iron is perfect for kit building or minor...
− +
-31%
Illuminated Capacitive Switch Module - Blue
$2.50 $3.60  
2 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-31%
Illuminated Capacitive Switch Module - Green
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-31%
Illuminated Capacitive Switch Module - Red
$2.50 $3.60  
1 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-31%
Illuminated Capacitive Switch Module - Yellow
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-20%
IMX219 Camera Module For Pi Cam V2 - 8 MegaPixels, 160° View Angle
$27.60 $34.50  
7 pc(s)
This IMX219 camera module is supplementary for Raspberry Pi official camera to fulfil the demands for wide view angle. It features 8-megapixel 160 degree view angle. If you got a Raspberry Pi Camera Board V2 and require wide view angle, here it is. Note : Follow the instruction in this...
− +
-40%
In-Line Power Switch - White
$0.60 $1.00  
3 pc(s)
This inline switch is great when you just want a simple on/off toggle switch that's already enclosed. Inside is a double pole rocker switch with screw terminals. Features : SPDT 6A, 250VAC Clicky Sound Dimensions : 60.9(L) x 26.5(W) x 15.5(H)mm
− +
-31%
In-line power switch for 2.1mm barrel jack
$2.50 $3.60  
10 pc(s)
Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an...
− +
-50%
Interface Cable RP-SMA to U.FL
$3.45 $6.95  
4 pc(s)
This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the DPAC 802.11 modules. Dimensions: 4" Length
− +
-50%
IOIO and Breadboard Holder
$2.60 $5.20  
1 pc(s)
This holder allows you to safely secure a IOIO development board and a self-adhesive breadboard in place to easily run jumper wires in between the two to form simple or complex prototyping circuits. Unlike it’s cousin, for the Arduino, this IOIO and breadboard holder has been made specifically...
− +
-7%
ISL29125 RGB Light Sensor
$12.50 $13.50  
2 pc(s)
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity...
− +
-33%
Jumper Cap - 2 Pin (Pack of 5)
$0.30 $0.45  
249 pc(s)
These are two pin jumper caps (also called shunts) that will create an electrical connection between two pin headers. Commonly used to modify settings on a board or device.
− +
-37%
Jumper Wire Kit
$2.50 $3.95  
1 pc(s)
This is a time saving kit of jumper wires - cut, stripped, and pre-bent for your prototyping pleasure. Included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each.
− +
-20%
Jumper Wires Premium 12" F/F Pack (Approx. 100pcs)
$25.60 $32.00  
13 pc(s)
These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Approx. 100 pcs per pack
− +
-20%
Jumper Wires Premium 6" F/F Pack (Approx. 100pcs)
$22.40 $28.00  
13 pc(s)
These are 6" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Approx. 100 pcs per pack
− +
-20%
Keypad - 16 Button (Alphanumeric)
$4.95 $6.20  
2 pc(s)
This is a basic 16 button keypad that has been designed for easy user input and functionality. The buttons are set up in a matrix format which allows a microcontroller to 'scan' the 8 output pins to see which of the 16 buttons is being pressed. Each of the keypad's 16 buttons has been...
− +
-8%
LilyPad Arduino 328 Main Board
$22.95 $24.95  
1 pc(s)
The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package designed to minimize snagging and profile,...
− +
-27%
LilyPad Buzzer
$6.50 $8.85  
2 pc(s)
This is a small buzzer for the LilyPad system. Use 2 I/O pins on the LilyPad main board and create different noises based on the different frequency of I/O toggling. Loud enough to hear inside a pocket but not obtrusively loud. Please note: This is an inductive buzzer meaning that is will act...
− +
-20%
LilyPad LED Blue (5pcs)
$4.75 $5.95  
3 pc(s)
This is a simple pack of five Blue LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-20%
LilyPad LED Pink (5pcs)
$4.75 $5.95  
7 pc(s)
Here is a simple 5 pack of pink LEDs for LilyPad, or whatever else you can dream up. Light up the night! LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting...
− +
-20%
LilyPad LED Red (5pcs)
$4.75 $5.95  
4 pc(s)
This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-20%
LilyPad LED White (5pcs)
$4.75 $5.95  
Out-of-stock
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
Out-of-stock
-20%
LilyPad LED Yellow (5pcs)
$4.75 $5.95  
7 pc(s)
This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-50%
LilyPad Protoboard Large
$4.75 $9.50  
1 pc(s)
This is a large board for prototyping through hole components with the LilyPad system. There are an array of pins all shorted together with 10mil traces. This allows for quick and easy prototyping - all you have to do is cut the traces between holes you don't want connected! Standard 0.1"...
− +
-31%
LilyPad Reed Switch
$5.50 $7.95  
1 pc(s)
The LilyPad Reed Switch is a simple breakout for a reed switch that will make it easy to use in e-textiles circuits in exactly the same manner that you can currently use the LilyPad Button and Switch. In order to make it more durable for wearable use, we've used a different style of reed switch,...
− +
-31%
LilyPad RGB LED
$5.50 $7.95  
3 pc(s)
Blink any color you need! Use the LilyPad RGB LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can produce a broad variety of colors. Each of the colors in the RGB LED are connected to one of the sew tabs on the board labeled R, G, and B. The color...
− +
-20%
LilyPad Simple Power
$13.55 $16.95  
Out-of-stock
The LilyPad Simple Power is a simple e-textile board that lets you connect and charge a lipo battery and switch it on or off, that’s it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no...
Out-of-stock
-50%
LilyPad SimpleSnap Protoboard
$6.00 $12.00  
3 pc(s)
The LilyPad SimpleSnap Protoboard is a new, easy way to create e-textiles projects with LilyPad that are modular and can be disassembled or broken down, it's also a great way to prototype! The SimpleSnap Protoboard is made to connect to the SimpleSnap main board so that the board is...
− +
-25%
LilyPad Slide Switch
$2.95 $3.95  
2 pc(s)
This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to...
− +
-9%
LiPo Charger Plus - USB Type-C
$15.00 $16.50  
1 pc(s)
The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and provided charge rate selection as well as optional thermal protection. Charge,...
− +
-25%
LiPower Shield
$36.00 $48.00  
2 pc(s)
Is there anything an Arduino can't do? Well, for one, most of them can't be powered directly from a 3.7V LiPo battery; much less charge and monitor that battery. The SparkFun LiPower Shield takes care of this by combining the functionality of two of our favorite battery power boards: the...
− +
-20%
Load Cell - 10kg, Straight Bar
$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 1kg, Straight Bar
$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Cell - 20kg, Straight Bar
$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 2kg, Straight Bar
$7.90 $9.90  
20 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 2kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Cell - 5kg, Straight Bar
$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock
-20%
Load Sensor - 50kg
$7.90 $9.90  
12 pc(s)
This load cell / sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. Each straight bar load cell is made from an aluminum-alloy and is capable of measure up to about 50kg. Documents : Specifications Load Sensor Tutorial (NerdKits)
− +
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
-21%
LPG Gas Sensor - MQ-6
$5.95 $7.50  
1 pc(s)
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing  LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has a high sensitivity and fast response...
− +
-30%
Membrane 3x4 Matrix Keypad
$1.65 $2.35  
3 pc(s)
This 12-button keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 7 microcontroller pins...
− +
-30%
Membrane 4x4 Matrix Keypad
$1.65 $2.35  
5 pc(s)
This 16-button keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 8 microcontroller pins...
− +
-20%
MEMS Microphone Breakout - INMP401 (ADMP401)
$12.80 $16.00  
1 pc(s)
This tiny breakout board features the ADMP401 MEMs microphone. One of the key advantages to this breakout and microphone is the bottom ported input. This means the microphone's input can fit flush against the enclosure of your project. Plus you will not have to deal with trying to solder the...
− +
1 2 3 4 5