On sale

1 2 3 4 5
Newest Items First
48 Per Page
-15%
MOSFET Power Controller
$12.50 $14.75  
2 pc(s)
MOSFETs are awesome. They're like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also has sewable pads so you can use it in e-textile projects that need more juice....
− +
-5%
Type 2 NFC Card - NTAG216
$2.85 $3.00  
53 pc(s)
A white plastic PVC card that has an NTAG216 chip embedded inside. About the size of a credit card, this is a blank white NFC card that you can use with a card printer to customize. It houses an NTAG216 chip which holds up to 888 bytes of memory. Documents : Datasheet (NTAG216)...
− +
-50%
Solar Panel - 18V 2.5W
$18.75 $37.50  
2 pc(s)
Need a clean energy source to power you project? Check out this high quality, high output solar panel. Each panel features high efficient polycrystalline cells mounted onto a fibreglass PCB and covered with epoxy resin which protect the cells without reducing efficiency. A weatherproof plastic...
− +
-20%
Servo - Generic Metal Gear (Micro Size)
$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...
− +
-15%
CAN-BUS Shield
$38.25 $45.00  
1 pc(s)
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output...
− +
-50%
3DR Buzzer for PX4 / Pixhawk
$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm
− +
-55%
3DR Safety Switch for PX4 / Pixhawk
$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +
-20%
MP3 Trigger
$60.00 $75.00  
1 pc(s)
Make some noise with your next project! The MP3 Trigger board is built to make it MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control,...
− +
-50%
Thermally Conductive Adhesive
$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...
− +
-20%
Resistor Kit - 1/4W 1% (600 total)
$6.40 $8.00  
9 pc(s)
Don't you hate it when you're in the middle of a build and you don't have a certain value of resistor? Don't let it happen again with this resistor kit. This kit contains a resistor color code chart and 20 each of 30 standard value 1/4 Watts resistors with 1% tolerance. It's perfect for starting...
− +
-20%
3.5" Resistive Touchscreen LCD + Pre-configured 16GB microSD Card For RaspberryPi
$37.60 $47.00  
7 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 3.5 inches 480x320 high resolution LCD display with resistive touchscreen, engineered specifically to let you quickly attached the...
− +
-20%
LilyPad LED White (5pcs)
$4.75 $5.95  
Out-of-stock
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
Out-of-stock
-8%
LilyPad Arduino 328 Main Board
$22.95 $24.95  
1 pc(s)
The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package designed to minimize snagging and profile,...
− +
-10%
Big Easy Stepper Motor Driver
$31.50 $35.00  
1 pc(s)
The Big Easy Driver, designed by Brian Schmalz , is a stepper motor driver board for bi-polar stepper motors up to 2A/phase. It is based on the Allegro A4983 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
-30%
3 Way Spring Clamp Terminal Block (Pack of 3)
$0.95 $1.35  
126 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
-29%
10mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
22 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 10mm Documents : Datasheet
− +
-29%
12mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet
− +
-29%
12mm Panel Mount Momentary Pushbutton - Green
$0.60 $0.85  
6 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Red)
$0.60 $0.75  
5 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including...
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Green)
$0.60 $0.75  
38 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1.5A@250VAC. Overall length (including...
− +
-33%
Panel Mount Pushbutton - Latching (10mm, Red)
$0.50 $0.75  
28 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
-29%
7mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 7mm Documents : Datasheet
− +
-20%
Load Cell - 1kg, Straight Bar
$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Cell - 5kg, Straight Bar
$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock
-20%
Load Cell - 10kg, Straight Bar
$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 20kg, Straight Bar
$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-50%
Capacitor Kit (300 Total)
$3.95 $7.90  
18 pc(s)
Our new capacitor kit comes with 10 each of 30 different capacitance values. All of these capacitors are packed into the zip-lock bags. This kit provides an easy way to build up a catalog of commonly used capacitors in a way that keeps them organised. Includes : Ceramic...
− +
-20%
Vibration Motor - 10x3.15mm
$2.00 $2.50  
46 pc(s)
This itty-bitty, shaftless vibratory motor is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. All moving parts are protected within the housing. With a 2.6-3.6V operating range, these units shake crazily at 3V. Once...
− +
-31%
LilyPad Reed Switch
$5.50 $7.95  
1 pc(s)
The LilyPad Reed Switch is a simple breakout for a reed switch that will make it easy to use in e-textiles circuits in exactly the same manner that you can currently use the LilyPad Button and Switch. In order to make it more durable for wearable use, we've used a different style of reed switch,...
− +
-37%
Jumper Wire Kit
$2.50 $3.95  
1 pc(s)
This is a time saving kit of jumper wires - cut, stripped, and pre-bent for your prototyping pleasure. Included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each.
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Adjustable Focus Lens
$39.00 $48.75  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Fisheye Lens
$48.00 $60.00  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
-10%
9V Battery Holder with On/Off Switch
$1.80 $2.00  
6 pc(s)
Enclosed battery holder for 9V battery. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-17%
4 x AA Battery Holder
$1.00 $1.20  
23 pc(s)
Battery holder for four AA batteries, terminated with ~150mm leads
− +
-50%
3 x AA Battery Holder with Switch and Cover
$1.00 $2.00  
1 pc(s)
Enclosed battery holder for three AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-20%
2 x AA Battery Holder
$0.80 $1.00  
Out-of-stock
Battery holder for two AA batteries, terminated with ~150mm leads
Out-of-stock
-20%
2 x AAA Battery Holder
$0.80 $1.00  
7 pc(s)
Battery holder for two AAA batteries, terminated with ~150mm leads
− +
-50%
3 x AA Battery Holder
$0.50 $1.00  
84 pc(s)
Battery holder for three AA batteries, terminated with ~150mm leads
− +
-33%
Rocker Switch - SPST Medium
$0.60 $0.90  
2 pc(s)
This switch is about the same size as our Rocker Switch -DPDT except that it's single-pole single-throw. It's rated for 6A@250V / 10A@125VAC and can be snap-in panel mounted. Documents : Dimensional Drawings
− +
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
-20%
microSD Shield
$19.60 $24.50  
1 pc(s)
Running out of memory space in your Arduino project? The SparkFun microSD Shield equips your Arduino with mass-storage capability, so you can use it for data-logging or other related projects. Communication with microSD cards is achieved over an SPI interface. The SCK, DI, and DO pins of the...
− +
-50%
Teensy SmartMatrix Shield Kit for RGB LED Panel
$12.45 $24.90  
12 pc(s)
The SmartMatrix Shield is the best way to connect the Teensy 3.2 to Large RGB LED matrix display panels . The shield makes it easy to connect the 13 signals required to drive the display, connects an external 5V supply to power the display and Teensy, and brings out the Teensy's free...
− +
-20%
PicoBoard
$55.20 $69.00  
1 pc(s)
The PicoBoard allows you to create interactions with various sensors. Using the Scratch programming language, you can easily create simple interactive programs based on the input from sensors. The PicoBoard incorporates a light sensor, sound sensor, a button and a slider, as well as 4...
− +
-31%
Panel Mount Toggle Switch - SPDT
$0.55 $0.80  
5 pc(s)
This heavy duty single-pole, double-throw (SPDT) toggle switch makes a great power switch or state selector for user interface. Rated for 6A at 125VAC. Includes a two threaded nuts and washer for mounting.
− +
-35%
Bare Conductive - Electric Paint (50ml)
$27.95 $43.00  
3 pc(s)
Bare Conductive's Electric Paint is just like any other water-based paint... except that it's electrically conductive! This means that you can actually paint wires onto things like models, clothes, furniture, walls, almost anything you can think of. Standard acrylic or water-based paints can...
− +
-29%
Tactile Button Assortment Pack of 12
$6.50 $9.10  
19 pc(s)
These tactile buttons are great for all sorts of projects. This assortment comes with 2 of each of 6 different colors for a total of 12 buttons. The colored caps are removable and the buttons fit into breadboards. See the drawing below for exact dimensions. Documents: Drawing
− +
1 2 3 4 5