On sale

1 2 3 4 5 6 7 8 9 10
Newest Items First
24 Per Page
-31%
Illuminated Capacitive Switch Module - Red
$2.50 $3.60  
1 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-31%
Illuminated Capacitive Switch Module - Yellow
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-20%
ZX Distance and Gesture Sensor
$31.95 $39.90  
2 pc(s)
The ZX Distance and Gesture Sensor is a touchless sensor that is capable of looking for simple gestures. Developed in conjunction with XYZ Interactive , the sensor uses their GestureSense® technology to recognize the distance of an object away from the sensor up to about 12 inches (30cm,...
− +
-15%
Ardumoto - Motor Driver Shield
$31.00 $36.50  
1 pc(s)
The Ardumoto Shield is a dual-motor controller for Arduino. Based on the L298 H-bridge, the SparkFun Ardumoto can drive two DC motors up to 2A per channel. Combined with an Arduino, the Ardumoto makes a fantastic controller platform for RC vehicles or even small autonomous robots. It's now...
− +
-20%
Raspberry Pi Zero Mini Camera - 72 Degree 60mm
$32.00 $40.00  
5 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
-38%
28mm Crocodile Clips (10 pcs)
$0.50 $0.80  
43 pc(s)
Pack of 10, 28mm Crocodile Clips. Excellent for fast prototyping where removable connections are essential. Features two side notches at the back of the clip for securing to leads and wires. Available as a pack of 10 clips. These miniature crocodile clips are perfect to use with...
− +
-30%
Membrane 3x4 Matrix Keypad
$1.65 $2.35  
3 pc(s)
This 12-button keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 7 microcontroller pins...
− +
-33%
Panel Mount Toggle Switch - DPDT
$0.60 $0.90  
1 pc(s)
This heavy duty double-pole, double-throw (SPDT) toggle switch is great for any project where you need two switches each with two options to select between. Rated for 6A at 125VAC. Includes threaded nuts and washer for mounting. Features! DPDT 6 Terminal ON-OFF-ON 3 - Position...
− +
-30%
Membrane 4x4 Matrix Keypad
$1.65 $2.35  
5 pc(s)
This 16-button keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 8 microcontroller pins...
− +
-33%
Rocker Switch - SPDT Small
$0.60 $0.90  
29 pc(s)
The rocker switch is a classic and this one is a great size for an unobtrusive on/off switch. It can be panel mounted and has two tabs for connecting wire. You can either solder wire or use a quick-connect connector. Features : Maximum Voltage: 250VAC Maximum Current: 3A @...
− +
-25%
LiPower Shield
$36.00 $48.00  
2 pc(s)
Is there anything an Arduino can't do? Well, for one, most of them can't be powered directly from a 3.7V LiPo battery; much less charge and monitor that battery. The SparkFun LiPower Shield takes care of this by combining the functionality of two of our favorite battery power boards: the...
− +
-20%
LilyPad LED Red (5pcs)
$4.75 $5.95  
4 pc(s)
This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-30%
Breadboard-Friendly 3.5mm Stereo Headphone Jack
$1.05 $1.50  
84 pc(s)
Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 2.54mm spacing so it plugs very...
− +
-20%
Load Sensor - 50kg
$7.90 $9.90  
12 pc(s)
This load cell / sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. Each straight bar load cell is made from an aluminum-alloy and is capable of measure up to about 50kg. Documents : Specifications Load Sensor Tutorial (NerdKits)
− +
-50%
3 x AAA Battery Holder with Cover and Switch
$1.00 $2.00  
13 pc(s)
Enclosed battery holder for three AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-20%
LilyPad LED Blue (5pcs)
$4.75 $5.95  
3 pc(s)
This is a simple pack of five Blue LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-40%
In-Line Power Switch - White
$0.60 $1.00  
3 pc(s)
This inline switch is great when you just want a simple on/off toggle switch that's already enclosed. Inside is a double pole rocker switch with screw terminals. Features : SPDT 6A, 250VAC Clicky Sound Dimensions : 60.9(L) x 26.5(W) x 15.5(H)mm
− +
-31%
In-line power switch for 2.1mm barrel jack
$2.50 $3.60  
10 pc(s)
Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an...
− +
-25%
Raspberry Pi GPIO Tall Header - 2x20
$2.90 $3.85  
22 pc(s)
This 2x20 "tall" header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can encapsulate your Pi. This through-hole header has 40 0.1"-spaced pins and can...
− +
-20%
Load Cell - 2kg, Straight Bar
$7.90 $9.90  
20 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 2kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
SOIC to DIP Adapter 8-Pin
$3.95 $4.95  
1 pc(s)
The SparkFun 8-Pin SOIC to DIP Adapter is a small PCB that lets you adapt SOIC packages into a DIP footprint. These tiny boards are useful for modding and upgrading devices that use 8-pin DIP ICs, when the upgraded IC is only available in a SOIC footprint. You can also use these adapters for...
− +
-20%
Solder Leaded - 15-gram Tube
$2.55 $3.20  
1 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
-50%
USB mini-B Cable - 1.5 meters w/Ferrite Bead
$2.25 $4.50  
53 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. The Ferrite Bead helps to eleminate EMI. Dimensions: 1.5 meter
− +
-21%
Analog 2-axis Thumb Joystick with Select Button
$1.55 $1.95  
3 pc(s)
This kit makes it easy to mount a PS2-like thumb joystick to your project. The 2-axis joystick contains two independent potentiometers (~10k ohm, one per axis, ) for reporting the joystick's position and a 'press in to select' button. Since it's analog, you'll need two analog reading pins on...
− +
1 2 3 4 5 6 7 8 9 10