Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11
5 - 13
Newest Items First
63 Per Page
10-Pin Alligator Clip to Female Rainbow Wire
$5.00  
10 pc(s)
For bread-boarding with unusual non-header-friendly surfaces, these rainbow wire will be your best friends! No longer will you have long strands of alligator clips that are grabbing little wires. These wires have a premium female header on one end, and a grippy mini alligator clip on the...
− +
M5StackC HAT - PIR Motion Sensor
$4.80  
10 pc(s)
PIR HAT is a M5StackC compatible PIR Motion Sensor. This is a pyroelectric sensor that detects motion by measuring changes in the infrared levels emitted by surrounding objects. When the motion is detected, the sensor will output HIGH and last for two seconds until the next detecting...
− +
M5Stack Stackable Module - GPS (72 Channels UBlox NEO-M8N)
$50.20  
1 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack GPS Module is built around the NEO-M8N GNSS module from ublox. The NEO-M8 modules utilize concurrent reception of up to three GNSS...
− +
M5Stack Stackable Module - STEPMOTOR
$25.50  
8 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Stackable STEPMOTOR module is built around three units of DRV8825 stepper motor controllers. It is perfect for any motion project as it can...
− +
M5Stack Stackable Module - Servo
$14.50  
4 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Stackable Servo module is designed for quick prototyping of servo motor project. It can supports up to 12 servo motors. The on-board MEGA328...
− +
M5StackC HAT - Speaker
$6.20  
7 pc(s)
SPK HAT is a M5StackC compatible speaker. This HAT module features a PAM8303 mono audio amplifier. PAM8303 is a class D amplifier, able to deliver up to 3 Watts into 4 ohm impedance speakers. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over...
− +
DC Barrel Jack Plug - Female
$0.50  
39 pc(s)
This female barrel jack plug is great for adding a common connector to the end of wires. This jack is compatible with 5.5x2.1mm barrel connectors. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.
− +
Wide Angle Ambient Light Sensor - BH1750
$26.70  
6 pc(s)
This Wide Angle Ambient Light Sensor is based on BH1750 - a digital ambient light sensor with a 16 bit AD converter built-in which can directly output a digital value in lux (Lx) over a range of 1 - 65535 lx. This sensor is far more accurate and easier to use as compare to photocell which...
− +
-50%
micro:Gamepad
$13.50 $27.00  
10 pc(s)
Micro:bit gamepad is an expansion gamepad based on micro:bit. You only need to plug in the micro:bit, it will turn into a wireless remote controller a wireless game console. This product packaged with acrylic plate, that giving it a good feel and no longer feels like a bare circuit...
− +
Analog pH Meter Kit V2
$69.95  
Out-of-stock
DFRobot Gravity: Analog pH meter V2 is specifically designed to measure the pH of the solution and reflect the acidity or alkalinity. It is commonly used in various applications such as aquaponics, aquaculture, and environmental water testing. As an upgraded version of pH meter V1,...
Out-of-stock
ESP32 Development Board U.FL w/Antenna
$23.50  
14 pc(s)
The ESP32 Development Board is a low-footprint, minimal system development board powered by ESP-WROOM-32 module. The ESP-WROOM-32 is a powerful and compact module that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...
− +
Alligator Test Leads (Pack of 10) - Small
$4.80  
18 pc(s)
Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them,...
− +
-7%
Type-K Thermocouple probe - 50mm
$6.99 $7.50  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 50mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-22%
Type-K Thermocouple probe - 100mm
$6.99 $9.00  
7 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 100mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-30%
Type-K Thermocouple probe - 150mm
$6.99 $10.00  
10 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 150mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-36%
Type-K Thermocouple probe - 200mm
$6.99 $11.00  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 200mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
NPN Transistors - 45V 800mA (BC337)
$0.50  
677 pc(s)
This BC337 is a drop-in replacement for the 2N2222 Transistor This is the BC337, an NPN silicon BJT (Bipolar Junction Transistor). This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The BC337 is specifically rated...
− +
Breadboard Power Supply 5V/3.3V
$2.95  
5 pc(s)
This Breadboard Power Supply Module plugs directly into a solderless breadboard and provides both 3.3V and 5V power directly to the breadboard power rails. The board accepts 7 to 12V DC input via the barrel jack or 5V via the mini-B USB port. It provides two regulated, fuse protected outputs...
− +
Temperature Sensor - Waterproof (DS18B20) w/Interface Board
$12.90  
8 pc(s)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a...
− +
I2C Adapter
$3.95  
3 pc(s)
This I2C Adapter provides a convenient way to connect the OLED display module and other I2C devices to Jetson Nano or Raspberry Pi. The 3.3V, Ground, SCL and SDA pins are breakout to multiple connectors. A XH2.54 cable is included in the package. NOTE : You can still access the 5V pin on...
− +
-9%
LiPo Charger Plus - USB Type-C
$15.00 $16.50  
1 pc(s)
The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and provided charge rate selection as well as optional thermal protection. Charge,...
− +
USB Cable A to Pigtail - 30cm
$2.95  
25 pc(s)
The USB Cable A to Pigtail provides a convenient method for hard wire a USB Type A connecting to a device or terminal block. One end of the cable is fitted with a strain relief USB Type A connector. The other end of the cable has stripped and tinned leads. This cable is commonly used to power...
− +
VL53L0X Time of Flight Distance Sensor - ~30 to 1000mm
$9.90  
5 pc(s)
The VL53L0X from ST Microelectronics is a time-of-flight ranging system integrated into a compact module. The sensor contains a very tiny invisible IR source, and a matching detector. It measures how long it takes for emitted pulses of infrared laser light to reach the nearest object and be...
− +
NVIDIA JetBot Mounting Kit
$3.50  
8 pc(s)
This mounting kit is intended for use with the NVIDIA JetBot robot. It includes the necessary screws and nuts to secure the Jetson Nano, motors, camera, etc., to the 3D printed chassis. Kit includes: 4x M3*25 Phillips pan head machine screw (stainless steel) 4x M3 nuts...
− +
Line Follower Sensor (Adjustable)
$1.99  
4 pc(s)
The Line Follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. It can detect transitions from light to dark (lines) or even objects directly in front of it. The sensor has an...
− +
Thin White Wheel for TT DC Gearbox Motors - 65mm Diameter
$1.95  
12 pc(s)
This Thin White Wheel For TT Gear Motor is equipped with a rubber tread with excellent traction, and a press-fit design to make connecting super quick and easy. Note : This wheel is only for use with TT gearbox motors . Wheel body: 65 x 18mm
− +
Orange and Clear Wheel for Bi-axial Gearbox Motor - 70mm Diameter
$2.50  
10 pc(s)
Need a wheel for your Bi-axial Gear Motor ? This Orange & Clear TT Motor Wheel is equipped with a nice, thick silicone tread and a press-fit design to make connecting super quick and easy. Make cute robots today with a couple of these orange wheels! Note : This wheel is only...
− +
Adafruit DC Motor + Stepper FeatherWing Add-on
$36.75  
7 pc(s)
This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). It features a fully-dedicated PWM driver chip that handles all the motor and speed controls over I2C. Since the FeatherWing only...
− +
Monochrome 0.91" 128x32 OLED Graphic Display - I2C
$9.50  
19 pc(s)
This miniature OLED display is perfect for adding graphics or texts to your next microcontroller project. It is small, measuring 0.91" across, but very readable due to the high contrast of an OLED display. This display is made of 128x32 individual blue OLED pixels, each one is turned on or...
− +
8 MegaPixels Camera Module for Jetson Nano (160° View Angle)
$49.50  
5 pc(s)
This 8 Mega Pixels Camera Module is a custom designed add-on for Jetson Nano. The camera features a Sony IMX-219 image sensor and uses the dedicated CSI interface for connecting to the Jetson Nano. This camera module is capable of 1080p video and still images. The board itself is tiny,...
− +
-20%
IMX219 Camera Module For Pi Cam V2 - 8 MegaPixels, 160° View Angle
$27.60 $34.50  
7 pc(s)
This IMX219 camera module is supplementary for Raspberry Pi official camera to fulfil the demands for wide view angle. It features 8-megapixel 160 degree view angle. If you got a Raspberry Pi Camera Board V2 and require wide view angle, here it is. Note : Follow the instruction in this...
− +
2.4GHz / 5GHz Duck Antenna RP-SMA w/ IPEX Interface Cable
$4.50  
11 pc(s)
2.4GHz/5GHz Duck Antenna with regular RP-SMA RF connector and IPEX interface cable for connecting to our dual mode wireless module . Includes: 1x Antenna 1x IPEX Interface cable Features: Type: Omni-Directional Frequency: 2400~2500MHz/5150~5850MHz Gain: 3dBi...
− +
25mm Delrin Plastic Ball Bearings For Jetbot
$2.45  
35 pc(s)
Delrin ball bearings are made of a composite material well-suited for low- to moderate-load applications. This 25mm ball bearings is specially sourced for the Nvidia Jetbot. Dimensions: 25mm diameter
− +
Slip Ring - 6 Wire (2A)
$18.95  
5 pc(s)
This is a 6 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an...
− +
RGB color Sensor With IR Filter & LED - TCS34725
$13.70  
Out-of-stock
The TCS34725 is probably the best color sensor on the market. It has a high sensitivity, wide dynamic range RGB and Clear light sensing elements. An integrated IR blocking filter minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. The...
Out-of-stock
-50%
Shaft - Solid 2mm Diameter x 90mm
$0.10 $0.20  
33 pc(s)
These 90mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 110mm
$0.10 $0.20  
5 pc(s)
These 110mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-46%
1 x AA Battery Holder with Cover and Switch
$1.00 $1.85  
19 pc(s)
This 1xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable sliding cover and an ON/OFF switch which can be used to control power to your project. The leads are about 150mm, and the last 5mm of them are tinned. Dimensions: 69 x 26...
− +
4 x AA Battery Holder with Switch & Barrel Jack
$3.50  
8 pc(s)
This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable sliding cover and an ON/OFF switch which can be used to control power to your project. The cable is terminated with a standard 5.5x2.1mm, center positive barrel jack...
− +
Round Shape 2 x CR2032 Coin Cell Battery Holder - 6V output with On/Off switch
$0.65  
7 pc(s)
This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm CR2032 coin cells in series to generate 6V nominal. CR2032 tends to have about 220mAh capacity so this holder would give you 6V @ 220mAh with two cells.
− +
Infrared Remote Control (21 Buttons)
$1.50  
10 pc(s)
Have you ever needed a cheap way to activate something from across the room? Infrared remotes are still the cheapest way to wirelessly control a device. This 21 buttons remote controller works with TSOP38238 infrared receiver which have an operating voltage from 2.5V - 5.5V. Includes :...
− +
Transparent Base Kit For Raspberry Pi
$3.90  
16 pc(s)
This is an acrylic base plate that can hold your Raspberry Pi and self-adhesive breadboard. The kit includes screws, washers and other accessories. Dimensions : 150mm x 100mm x 3mm
− +
SRF05 Low Cost Ultrasonic Range Finder w/Header
$28.90  
2 pc(s)
The SRF05 is an evolutionary step from the SRF04, and has been designed to increase flexibility, increase range, and to reduce costs still further. As such, the SRF05 is fully compatible with the SRF04. Range is increased from 3 meters to 4 meters. A new operating mode (tying the mode...
− +
-50%
ubit:connect Interfacing Board for BBC micro:bit - Assembled
$16.75 $33.50  
116 pc(s)
This ubit:connect Interfacing Board is specially designed for BBC micro:bit developer. It offers an easy way to connect sensors, actuators and other circuits to the micro:bit. The board comes with an 0.91" OLED display. Together with SGBotic's customised makecode package, this OLED display...
− +
micro:bit Flex Sensor
$32.50  
4 pc(s)
This micro:bit Flex Sensor is specifically designed for micro:bit to detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. This sensors are easy to use. It will vary its resistance depending on how much it...
− +
-23%
Air Quality Breakout - CCS811
$29.90 $38.90  
2 pc(s)
The CCS811 Air Quality Breakout is a digital gas sensor solution that senses a wide range of Total Volatile Organic Compounds (TVOCs), including equivalent carbon dioxide (eCO2) and metal oxide (MOX) levels. VOCs are often categorized as pollutants and/or sensory irritants and can come...
− +
3.3V, 1A Step-Down Voltage Regulator D24V10F3
$14.50  
5 pc(s)
This D24V10F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.3V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 80% and 90% and has a very low dropout, so it can be used with input...
− +
Protoboard, Strip, 10x24cm
$4.50  
2 pc(s)
Ideal for development and prototyping work, this protoboard is designed primarily for hard wiring of discrete components, typically in analogue circuits, but is equally useful where a number of common bus or signal lines are required. Size: 10 x 24cm, 1.5mm thick
− +
3-Blade Nylon Boat Propeller Set - 36mm Diameter
$2.00  
4 pc(s)
Small nylon propeller for port and starboard thruster. Featuring both left- and right-handed rotation. 3 blades and 36mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø36 x 18.5mm Center bore：1.9 mm
− +
Non-Isolated Single Relay Module For 3V Controller
$6.50  
1 pc(s)
This single channel Relay Module is specially designed for low-voltage devices and works well with 3.3V power supply. It can be used to control the lighting, electrical and other equipments through the digital IO port. The module comes with on-board back EMF protection to eliminate the...
− +
Non-contact Liquid Level Sensor (PNP Output)
$19.95  
2 pc(s)
This non-contact liquid level sensor can be triggered when the liquid level fall below the sensor attached to the outside surface of a non-metal container. Unlike traditional liquid level sensors, it does not need to be immersed into liquid. So, in this way, liquid will not be contaminated...
− +
Passive Piezo Buzzer w/Leads -13mm
$2.90  
3 pc(s)
This is a small 13mm round passive buzzer that operates around the audible 4kHz range. We drove it directly from a 3v to 5V Arduino or micro:bit to generate simple melody. The buzzer leads are terminated with male pin. Note : This passive buzzer requires a square wave (PWM) signal to...
− +
-50%
Single Row Break Away Pin Header - Straight (Blue)
$0.75 $1.50  
135 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Pin Header - Straight (Red)
$0.75 $1.50  
25 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Pin Header - Straight (White)
$0.75 $1.50  
15 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Pin Header - Straight (Yellow)
$0.75 $1.50  
240 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
Beefcake Relay Control Kit (Ver. 2.0)
$12.50  
1 pc(s)
Your 5V system can wield great power with this big, beefy relay board. How does 10A on the NC contacts and 20A on the NO contacts at 220VAC sound? The SparkFun Beefcake Relay Control Kit contains all the parts you need to get your high-power load under control. Only minimal assembly is...
− +
Outdoor Type 2 NFC Tag - NTAG213 (Diameter 40mm)
$6.50  
1 pc(s)
This disc-shaped, waterproof tag contains a small NTAG213 RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple centimeter away.. The housing will withstand rugged conditions and is designed for outdoor use. It can be secured with screws. You can...
− +
Outdoor Type 2 NFC Tag - NTAG213 (Diameter 52mm)
$6.95  
5 pc(s)
This disc-shaped, waterproof tag contains a small NTAG213 RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple centimeter away.. The housing will withstand rugged conditions and is designed for outdoor use. It can be secured with screws. You can use...
− +
-40%
USB microB Cable - 1.5 meter
$3.00 $5.00  
1158 pc(s)
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
− +
Cool White LED Flexi-Strip - 5V (Bare, 5 meters)
$36.00  
3 pc(s)
These single color LED strip feature 60 ultra bright cool white LEDs on one meter. As these are bare LED strips that have no protective coating, your project won't be water proof but there is access to each LED and each strip length can be easily modified. Each of these strips need a 3V to 5V...
− +
WS2812B RGB Matrix - 8x8 (64 LED)
$12.99  
6 pc(s)
This is the RGB LED matrix panel with 64 WS2812B LEDs arranged in an 8x8 matrix. Each LED is capable of drawing as much as 60mA (at peak brightness the matrix can draw just over 3.5 Amps at 5 Volts), this adds up so it is suggested to use a 5V 2A power supply. For most uses, you'll see about...
− +
2.8" TFT Resistive Touch Shield for Arduino w/microSD Socket
$25.00  
1 pc(s)
The 2.8" resistive touch LCD shield is specifically designed for the Arduino Uno and Mega. It features 2.8" screen with 240x320 pixels, and has a resistive touchscreen attached for direct user interaction. The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply...
− +
1 2 3 4 5 6 7 8 9 10 11
5 - 13

Recently Viewed