Delivery fee

New items

1 - 8
2 3 4 5 6 7 8 9 10 11 12 13
Sort by Price: Low to High
63 Per Page
-7%
RF Link Receiver - 4800bps (434MHz)
$8.50 $9.10  
2 pc(s)
These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
Timing Belt - 2GT (Length 852mm)
$8.50  
1 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 852mm,...
− +
ESP8266 Wifi Module SMD
$8.90  
4 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...
− +
Kitronik Edge Connector Breakout Board for BBC micro:bit
$8.90  
9 pc(s)
Looking to do more with your BBC micro:bit? Unlock its potential with this pre-built version of our Edge Connector Breakout Board! This breakout board has been designed to offer an easy way to connect additional circuits and hardware to the pins on the edge of the BBC micro:bit. It provides...
− +
MI:power board for the BBC micro:bit
$9.50  
3 pc(s)
When assembled, the MI:power board is connected directly to the 3V, GND and P0 connections on the micro:bit. The 3V and GND connections provide power to the micro:bit and the built in buzzer is connected to P0, which is the default output pin when using the audio functions in the Block Editor...
− +
2-CH IR Remote Relay Controller (Soldering Kit)
$9.50  
5 pc(s)
This fun little soldering kit enables you to make a 2-channel infra-red remote relay controller. The kit features a microcontroller that takes command from an infra-red receiver and controls 2 relays individually. Using an infra-red keypad, you will be able to turn on/off the relays....
− +
Monochrome 0.91" 128x32 OLED Graphic Display - I2C
$9.50  
19 pc(s)
This miniature OLED display is perfect for adding graphics or texts to your next microcontroller project. It is small, measuring 0.91" across, but very readable due to the high contrast of an OLED display. This display is made of 128x32 individual blue OLED pixels, each one is turned on or...
− +
Cap Nuts M3 (50 pcs)
$9.50  
1 pc(s)
Cap nuts come in packages of 50 pieces. They will give your MakerBeam project an extra finish.
− +
Pan/Tilt Bracket
$9.50  
1 pc(s)
This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. This pan/tilt bracket works with our small servo motor . Documents: Dimensional Drawing Assembly Guide
− +
Capacitive Touch Breakout - AT42QT1011
$9.50  
2 pc(s)
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1011 SparkFun Capacitive Touch Breakout offers a single, momentary capacitive touch button with easy-to-use digital I/O pins. The AT42QT1011 is a dedicated,...
− +
2-CH IR Remote Motor Controller (Soldering Kit)
$9.50  
2 pc(s)
This fun little soldering kit contains all the parts required to make a 2-channel infra-red remote motor controller. The kit features a microcontroller that takes command from an infra-red receiver and controls the speed of two motors individually. Using an infra-red keypad and four AA size...
− +
600mm MakerBeam Clear Anodised (Threaded)
$9.50  
30 pc(s)
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
− +
VL53L0X Time of Flight Distance Sensor - ~30 to 1000mm
$9.90  
5 pc(s)
The VL53L0X from ST Microelectronics is a time-of-flight ranging system integrated into a compact module. The sensor contains a very tiny invisible IR source, and a matching detector. It measures how long it takes for emitted pulses of infrared laser light to reach the nearest object and be...
− +
LCD Keypad Shield for Arduino
$9.90  
1 pc(s)
The LCD Keypad Shield for Arduino includes a 2x16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD. Analog Pin 0 is used to read the push buttons. The shield operates at 5V. Features: Contrast adjustment (turns...
− +
Soldering Iron Stand
$9.90  
3 pc(s)
This is a simple soldering iron stand with heavy base for excellent stability. A cleaning sponge is included. Note: Not compatible with TOL-01027
− +
Soil Moisture Sensor - Long Probe
$9.90  
Out-of-stock
This Soil Moisture Sensor is used to measure the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two long exposed metal rods function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil...
Out-of-stock
Force Sensitive Resistor 0.5" (FSR402) - Male Pin Header
$9.90  
1 pc(s)
This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will...
− +
Temperature Sensor - Waterproof (DS18B20) w/Male Pin Header
$9.90  
5 pc(s)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a...
− +
Wire Strippers 30AWG
$9.90  
10 pc(s)
These are good quality 6" wire strippers with 6 gauge settings. We really wanted to stock these because they strip 30AWG wire wrap wire nicely as well as the standard 22AWG hook up wire. Features: 30, 28, 26, 24, 22, 20 AWG settings 0.25, 0.32, 0.4, 0.5, 0.6, 0.8 mm...
− +
MakerBeamXL - 500mm Clear Anodised (Threaded)
$9.90  
28 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
VL6180X Time of Flight Distance Sensor - 60cm Max
$9.90  
2 pc(s)
This sensor is a breakout board for ST's VL6180X proximity and ambient light sensor, which measures the range to a target object up to 20 cm away (or 60 cm with reduced resolution). The VL6180X uses time-of-flight measurements of infrared pulses for ranging, allowing it to give accurate results...
− +
Timing Belt - 2GT (Length 1220mm)
$9.90  
4 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 1220mm,...
− +
MakerBeamXL - 500mm Black Anodised (Threaded)
$9.90  
13 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
M12 (S-Mount) lens - 16mm (5 MegaPixels)
$9.95  
3 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 16mm fixed lens with IR Cut Filter...
− +
Line Follower Array
$9.95  
31 pc(s)
This SGBotic Line Follower Array gives your robot the ability to follow a dark line on a white background or vice-versa. It has four IR sensors that have been configured to output digital signal. The array features visible LEDs which turn on when the sensors detect reflected IR light. You...
− +
M5StackC HAT - ENV Environmental Sensor
$9.95  
4 pc(s)
ENV HAT is a M5StackC compatible environmental sensor for sensing temperature, humidity, barometric pressure and geomagnetic. It consists of three sensors - BMM150 for geomagnetic sensing, BMP280 for barometric pressure sensing and DHT11 to measure temperature and humidity. Because...
− +
ACHS-7124 Current Sensor Carrier -40A to +40A
$9.95  
1 pc(s)
This board is a simple carrier of Broadcom's bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. This version accepts a bidirectional current input with a magnitude up to 40A and...
− +
HDMI Cable - 1.5 Meters
$9.95  
2 pc(s)
This is an inexpensive HDMI cable that you can use to hook up your Raspberry Pi 3B to a suitable monitor or TV. Heck, you can hook up anything you want with it, HDMI is becoming more and more common as a digital audio/video standard. Dimensions: 1.5 meters Long
− +
ACHS-7123 Current Sensor Carrier -30A to +30A
$9.95  
2 pc(s)
This board is a simple carrier of Broadcom's bidirectional ± 30A ACHS-7123 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. This version accepts a bidirectional current input with a magnitude up to 20 A...
− +
Analog/Digital MUX Breakout
$9.95  
3 pc(s)
This is a breakout board for the very handy 16-Channel Analog/Digital Mulitplexer/Demultiplexer CD74HC4067. This chip can be used to connect 16 analog sources (like sensors) to 5 pins on a microcontroller. 4 of the pins must be digital pins, 1 pin must be an analog to digital conversion pin....
− +
-50%
Wheel Encoder Kit
$9.95 $19.95  
10 pc(s)
The simple encoder kit from consists of two neodymium 8-pole magnets with rubber hubs and two hall-effect sensors terminated with 150mm (6inch) cable and 3 pin female servo headers. The magnets have 4 north poles and 4 south poles and are strong enough that the sensor can detect the poles from...
− +
Access Barrier Kit
$9.95  
Out-of-stock
When entering a carpark, a barrier bar will lift up for a car to pass through. When a train passes by, a barrier bar will come down to stop the cars from driving past. This Access Barrier Kit simulates such a barrier bar. The kit uses a servo motor to lift up/down the barrier bar and...
Out-of-stock
Solder Leaded - 100-gram Spool
$9.95  
3 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 100 grams. Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
-30%
Basic 20x4 Character LCD - Black on Green 3V
$9.95 $14.20  
35 pc(s)
This is a basic 20 character by 4 line display. Utilizes the extremely common HD44780 parallel interface chipset ( datasheet ). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes LED backlight. This LCD works on 3V supply....
− +
Bluetooth 4.0 USB Module (v2.1 Back-Compatible)
$9.95  
17 pc(s)
This is a handy little USB Bluetooth 4.0 dongle. Utilising the CSR8510 chipset, this dongle is backwards compatible with v2.1 and earlier, but also supports the latest v4.0 low energy bluetooth transmission. It has a maximum distance of up to 50m and includes an indicator LED. Use this Dongle...
− +
HDMI to VGA Video Adapter w/Audio and USB Power Out (Metal Case)
$9.95  
1 pc(s)
This nifty adapter cable with durable metal casing converts the digital HDMI video signals which are outputted from Raspberry Pi, into an analog signal required by the widely used VGA monitor. This adapter has an audio jack that provides stereo headphone/line out (HDMI 1.3 cables carry both...
− +
-20%
Hakko Soldering Iron - 40W 230V EU Plug
$9.95 $12.50  
37 pc(s)
This is a simple fixed temperature, quick heating soldering iron from Hakko. It is not as powerful as soldering station such as Hakko FX-888, but if you really need a low cost iron for your tool box, this lovely iron is a good choice. At 40W, this iron is perfect for kit building or minor...
− +
MAX6675 Temperature Sensor Kit with K-Type Thermocouple
$9.99  
3 pc(s)
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. This MAX6675 breakout board does everything for you, and can be easily interfaced with Arduino, micro:bit, Raspberry Pi and any other microcontroller via 12-bit resolution SPI bus. A...
− +
STM8 & STM32 Emulator and Programmer (Assorted Colors)
$9.99  
2 pc(s)
This low cost, easy to use USB Emulator and Programmer supports ST's range of STM8 and STM32 microcontrollers .The programmer will work with software that is compatible with the ST-Link V2 programmer, including Arduino IDE and ST's STM32CubeProg . This programmer is also ideal for use...
− +
Mini Vacuum Pump - 6V
$9.99  
5 pc(s)
This mini vacuum pump operates at 6V and has enough suction for most small projects such as blood pressure monitors and automatic machine assembly. Features: Rated Voltage: 6VDC Rated Current: <420mA Inflation Time: <10 S (From 0 to 300 mmHg in a 500CC...
− +
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Sensor Cable - Electrode Pads (3 connector)
$10.50  
1 pc(s)
Note : This product is  NOT  a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm...
− +
Breakout Board for Electret Microphone
$10.95  
2 pc(s)
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller's analog-to-digital converter. Each breakout comes fully assembled and works...
− +
Circuit Explorer for BBC Micro:bit
$10.95  
6 pc(s)
Introducing the new Circuit Explorer for BBC Micro:bit from SGBotic. This breakout board offers an easy way to connect additonal circuit and sensors to the micro:bit using the crocodile clips and copper tape. The back of the Circuit Explorer is made flat so that it can stick to any clean...
− +
25D mm Metal Gearmotor Bracket Pair
$11.00  
1 pc(s)
These aluminum gearmotor brackets let you securely mount Pololu's 25D mm metal gearmotors to your project. The brackets are sold in pairs , and each bracket includes four M3 screws for securing the motor to the bracket. Each bracket also features seven mounting holes and fourteen mounting...
− +
Grove - Alcohol Sensor
$11.50  
2 pc(s)
Alcohol sensor is semiconductor sensor for alcohol detection. It has good sensitivity and fast response to alcohol, suitable for portable alcohol detector. Features : Power requirements: 5 VDC @ ~120 mA (heater on) Detection Gas: Alcohol Concentration: 20-1000ppm Alcohol Interface: 1 TTL...
− +
-20%
Small Stepper Motor
$11.60 $14.50  
1 pc(s)
These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. Features : Stride Angle (degrees) : 7.5 2-Phase Rated Voltage : 12V Rated Current : 400mA 3mm Diameter Drive Shaft...
− +
M3 Nuts
$11.90  
1 pc(s)
1 bag of approximately 250 pcs M3 nuts. Compatible with all MakerBeam bolts
− +
Breakout Board for microSD w/Level Shifter
$11.90  
4 pc(s)
This Level Shifting microSD Breakout from Sparkfun is quite similar to the microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino's SD library's top speed on a 5V system. With this small breakout board, that is...
− +
Mini Real Time Clock Module (DS3231) for Raspberry Pi
$11.95  
5 pc(s)
Unlike most computers, the Pi lacks a Real-Time Clock (RTC). This means the Pi doesn't know what time it is when powered on. While your Pi is connected to a network it will be able to set it's clock correctly using NTP ( Network Time Protocol ) server. Without a network connection your Pi...
− +
Sharp Infrared Distance Sensor GP2Y0A41SK0F - 4 to 30cm
$12.00  
23 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 3.1V at 4cm to 0.3V at 30cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor. See 3-pin Cable for Sharp Sensors...
− +
KittenBot IO:bit for micro:bit - Version 2.0
$12.00  
11 pc(s)
This KittenBot's IO:bit is a feature packed expansion board for the micro:bit. It breaks out all the IO pins (inputs, outputs) and adds extra hardware to make your next micro:bit project shine. The small form factor and two LEGO-compatible pin holes make it easy to fit into the project you might...
− +
-50%
Teensy SmartMatrix Shield Kit for RGB LED Panel
$12.45 $24.90  
12 pc(s)
The SmartMatrix Shield is the best way to connect the Teensy 3.2 to Large RGB LED matrix display panels . The shield makes it easy to connect the 13 signals required to drive the display, connects an external 5V supply to power the display and Teensy, and brings out the Teensy's free...
− +
Beefcake Relay Control Kit (Ver. 2.0)
$12.50  
1 pc(s)
Your 5V system can wield great power with this big, beefy relay board. How does 10A on the NC contacts and 20A on the NO contacts at 220VAC sound? The SparkFun Beefcake Relay Control Kit contains all the parts you need to get your high-power load under control. Only minimal assembly is...
− +
-10%
Solder Lead Free - 100-gram Spool
$12.50 $13.95  
1 pc(s)
This is your basic spool of lead free solder with a water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced users that should last 6-12 months depending on how often you solder. If you are just beginning to solder, we recommend you order the...
− +
Adjustable Infrared Reflection Sensor (3- 80cm)
$12.50  
14 pc(s)
This is a simple to use infra-read sensor switch. Power it up with 5V and it can detects object within 3 to 80cm. It is widely used in mobile robot for obstacle detection, interactive media, industrial assembly line and many other applications. The detection distance can be adjusted...
− +
900mm MakerBeam Clear Anodised (Threaded)
$12.50  
1 pc(s)
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
− +
-7%
ISL29125 RGB Light Sensor
$12.50 $13.50  
2 pc(s)
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity...
− +
-15%
MOSFET Power Controller
$12.50 $14.75  
2 pc(s)
MOSFETs are awesome. They're like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also has sewable pads so you can use it in e-textile projects that need more juice....
− +
Adjustable Infrared Reflection Sensor (3- 50cm)
$12.50  
4 pc(s)
This is a simple to use infra-read sensor switch. Power it up with 5V and it can detects object within 3 to 50cm. It is widely used in mobile robot for obstacle detection, interactive media, industrial assembly line and many other applications. The detection distance can be adjusted from 3-...
− +
2.4GHz Duck Antenna RP-SMA
$12.60  
7 pc(s)
2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long. The FCC is moving towards Part 15 compliance. All this means is that all the SMA RF connectors are changing gender. Really annoying for those of...
− +
Sharp Infrared Distance Sensor GP2Y0A21YK - 10 to 80cm
$12.70  
2 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 3.1V at 10cm to 0.3V at 80cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor - see 3-pin cable for Sharp Sensors...
− +
-20%
MEMS Microphone Breakout - INMP401 (ADMP401)
$12.80 $16.00  
1 pc(s)
This tiny breakout board features the ADMP401 MEMs microphone. One of the key advantages to this breakout and microphone is the bottom ported input. This means the microphone's input can fit flush against the enclosure of your project. Plus you will not have to deal with trying to solder the...
− +
1 - 8
2 3 4 5 6 7 8 9 10 11 12 13

Recently Viewed