Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11 12 13
Sort by Popularity
63 Per Page
I2C 20x4 Character LCD Module - Black on Green 5V
$17.95  
8 pc(s)
This is another great 20x4 character LCD display with I2C interface. As the pin resources of Arduino controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you...
− +
Mini Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
Out-of-stock
Looking for a battery powered liquid pump for your Micro:Bit project? This submersible Mini Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with...
Out-of-stock
-20%
Raspberry Pi Zero Mini Camera - 72 Degree 60mm
$32.00 $40.00  
5 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
-30%
3 Way Spring Clamp Terminal Block (Pack of 3)
$0.95 $1.35  
126 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
Passive Piezo Buzzer w/Leads -13mm
$2.90  
3 pc(s)
This is a small 13mm round passive buzzer that operates around the audible 4kHz range. We drove it directly from a 3v to 5V Arduino or micro:bit to generate simple melody. The buzzer leads are terminated with male pin. Note : This passive buzzer requires a square wave (PWM) signal to...
− +
I2C Adapter
$3.95  
3 pc(s)
This I2C Adapter provides a convenient way to connect the OLED display module and other I2C devices to Jetson Nano or Raspberry Pi. The 3.3V, Ground, SCL and SDA pins are breakout to multiple connectors. A XH2.54 cable is included in the package. NOTE : You can still access the 5V pin on...
− +
-31%
Illuminated Capacitive Switch Module - Red
$2.50 $3.60  
1 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
MakerBeamXL - 1000mm Black Anodised (Threaded)
$15.50  
22 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
Voltage Regulator - 3.3V
$2.75  
20 pc(s)
This is the basic LD1117V33 voltage regulator, a low drop positive regulator with a 3.3V fixed output voltage. This fixed regulator provides a great amount of stability and protection for your project and with its on chip trimming this regulator is able to reach an output voltage tolerance...
− +
Miniature PIR Motion Sensor
$4.50  
6 pc(s)
This miniature PIR sensor is designed for motion detection. It uses pyroelectric sensor to detect motion by measuring changes in the infrared levels emitted by surrounding objects. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that...
− +
Temperature Sensor - Waterproof (DS18B20) w/Interface Board
$12.90  
7 pc(s)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a...
− +
RGB color Sensor With IR Filter & LED - TCS34725
$13.70  
Out-of-stock
The TCS34725 is probably the best color sensor on the market. It has a high sensitivity, wide dynamic range RGB and Clear light sensing elements. An integrated IR blocking filter minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. The...
Out-of-stock
Opto-Isolated Relay Module - 16 Channels (5V)
$22.99  
1 pc(s)
This 16 channels Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. The digital input circuit is optically isolated from the relay, so your controller is protected from voltage spikes and surges. The module is controlled with 5V...
− +
-20%
RFID Tag - 125kHz
$2.35 $2.95  
19 pc(s)
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic RFID tag works in the 125kHz RF range and comes with a unique 40-bit ID. It is not re-programmable. This blank, smooth, and mildly...
− +
-33%
Panel Mount Pushbutton - Latching (10mm, Red)
$0.50 $0.75  
28 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
MakerBeam Hinge Kit
$29.50  
11 pc(s)
1 bag of MakerBeam hinges kit contains 8 hinges and 4 axes (ISO7380, M3, 14mm, A2) and 4 self locking nuts (DIN985).The hinges were specially designed to make a hinge or to mount a beam at any angle you would like.
− +
Line Follower Sensor
$1.99  
6 pc(s)
The Line Follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. It can detect transitions from light to dark (lines) or even objects directly in front of it. The sensor has an...
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Red)
$0.60 $0.75  
5 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including...
− +
-20%
4 x AAA Battery Holder with Cover and Switch
$2.00 $2.50  
13 pc(s)
Enclosed battery holder for four AAA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
DIP Switch - 3 Position
$0.40  
17 pc(s)
DIP switch with 3 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
− +
-9%
LiPo Charger Plus - USB Type-C
$15.00 $16.50  
1 pc(s)
The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and provided charge rate selection as well as optional thermal protection. Charge,...
− +
Rotary Potentiometer Breakout - 10k Ohm
$1.95  
7 pc(s)
An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC, GND, and the OUT pin will have a voltage that varies from 0 to VCC depending on the rotation of the pot. Hook the OUT pin to an ADC on a microcontroller and get a...
− +
-20%
LilyPad LED Red (5pcs)
$4.75 $5.95  
4 pc(s)
This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
Sunflower Solar Power Manager 5V
$14.50  
3 pc(s)
Solar Power Manager 5V is a small power and high-efficiency solar power management module designed for 5V solar panel. It features as MPPT (Maximum Power Point Tracking) function, maximizing the efficiency of the solar panel. Apart from serving as a solar charger, the module can provide up to...
− +
Copper Tape - 10mm (20 Meters)
$5.99  
9 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is...
− +
Thin White Wheel for TT DC Gearbox Motors - 65mm Diameter
$1.95  
12 pc(s)
This Thin White Wheel For TT Gear Motor is equipped with a rubber tread with excellent traction, and a press-fit design to make connecting super quick and easy. Note : This wheel is only for use with TT gearbox motors . Wheel body: 65 x 18mm
− +
MicroSD Card Adapter
$0.20  
33 pc(s)
The micro SD card adapter looks like a regular-sized SD card with a slot in it for the microSD card. It allows you to transfer data between your device and a computer.
− +
Non-contact Liquid Level Sensor (Open Collector Output)
$19.95  
4 pc(s)
This non-contact liquid level sensor can be triggered when the liquid level fall below the sensor attached to the outside surface of a non-metal container. Unlike traditional liquid level sensors, it does not need to be immersed into liquid. So, in this way, liquid will not be contaminated...
− +
T5577 RFID Tag - Read/Write 125kHz
$2.95  
8 pc(s)
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic T5577 RFID tag works in the 125kHz RF range and supports read/write operation. Note : This is a blank tag - its ID must be chosen and...
− +
Rotary Encoder Breakout
$2.50  
Out-of-stock
The rotary encoder is a rotary input device that provides an indication of how much and in which direction the encoder has been turned. This 20-pulse Rotary Encoder Breakout has a nice 'clicking' feel and also has a push-button built into it so you can press onto the knob to close a separate...
Out-of-stock
Line Follower Sensor (Adjustable)
$1.99  
Out-of-stock
The Line Follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. It can detect transitions from light to dark (lines) or even objects directly in front of it. The sensor has an...
Out-of-stock
USB Cable A to Pigtail - 30cm
$2.95  
25 pc(s)
The USB Cable A to Pigtail provides a convenient method for hard wire a USB Type A connecting to a device or terminal block. One end of the cable is fitted with a strain relief USB Type A connector. The other end of the cable has stripped and tinned leads. This cable is commonly used to power...
− +
Adafruit DC Motor + Stepper FeatherWing Add-on
$36.75  
7 pc(s)
This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). It features a fully-dedicated PWM driver chip that handles all the motor and speed controls over I2C. Since the FeatherWing only...
− +
M12 (S-Mount) Plastic Lock Ring
$0.10  
117 pc(s)
M12x0.5mm Plastic Lock Ring for securing M12 Lenses on lens holders.
− +
8x8 SPI Dot Matrix Display Module - MAX7219 - Red
$3.90  
7 pc(s)
This 8x8 SPI Dot Matrix Module allows you to experiment with dot matrix LED's without all the complicated wiring. The module makes use of the MAX7219 LED driver which handles all the complicated stuff such as multiplexing the LEDs and driving them at the correct currents. What's more, the...
− +
UV 400nm Purple LED Clear Lens - 5mm (10 pcs)
$2.95  
45 pc(s)
These LEDs emit UV 'blacklight' in the UV spectrum so they are great for projects with fluorescent materials referred to as UV/blacklight-reactive or 'glow-in-the dark'. They are bright (350mcd) and have about a 20-degree LED beam. They go easily into a breadboard and come in a pack of ten so...
− +
Copper Tape - Conductive Adhesive, 10mm (20 Meters)
$6.90  
Out-of-stock
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
Out-of-stock
MQ-7 Gas Sensor (Carbon Monoxide)
$4.50  
2 pc(s)
This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to Carbon...
− +
Photocell Light Sensor Module (Analog Output)
$1.20  
8 pc(s)
The LDR Sensor Module is used to detect the presence of light / measuring the intensity of light. The output of the module goes LOW in the presence of light and it becomes HIGH in the absence of light. Features: Voltage: 3.3V~5V Analog output Dimensions: 21 x...
− +
-20%
MP3 Trigger
$60.00 $75.00  
1 pc(s)
Make some noise with your next project! The MP3 Trigger board is built to make it MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control,...
− +
-31%
Illuminated Capacitive Switch Module - Green
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
Bi-axial Gear Motor (1:143)
$3.50  
4 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 660mA while possessing a gearbox ratio of 1:134 and a wheel...
− +
-50%
Pulley For Toy Motorr - 17mm Diameter
$0.15 $0.30  
8 pc(s)
This plastic pulley can be used to drive wheels or other pulleys with 2mm diameter belt. They have an outer diameter of 17mm and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø17 x 4mm
− +
433MHz Spring Coil Antenna
$0.75  
9 pc(s)
This spring coil antenna is designed for the 433MHz devices. Each antenna is constructed of phosphor copper. Features: Frequency Range(MHz)：433MHz +/-5MHz Gain(dBi)：2.15 V.S.W.R：≤1.5@433M Input Impedance( OHM)：50 Spring outer diameter: Wire diameter is 0.6mm,...
− +
3.5mm Stereo Audio Jack Terminal Block
$1.95  
9 pc(s)
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is...
− +
-50%
SparkFun moto:bit
$22.50 $45.00  
4 pc(s)
The SparkFun moto:bit is a fully loaded "carrier" board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional robotics platform. The moto:bit offers a simple, beginner-friendly robotics controller capable of operating a basic robotics chassis. Onboard...
− +
WS2812 RGB LED Stick (w/Male Pin Header)
$2.80  
12 pc(s)
This is the WS2812 Addressable RGB LED Stick with eight LEDs. The WS2812 is a addressable smart RGB LED that uses a single data line to control brightness and colour. The embedded constant-current driver keeps the LED brightness consistent even if the input voltage varies. There are...
− +
DIP Switch - 5 Position
$0.60  
22 pc(s)
DIP switch with 5 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
− +
Panel Mount Pushbutton - Latching (10mm, Green)
$0.50  
35 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
Mini HDMI to HDMI Cable - 1.5 meter
$7.99  
3 pc(s)
Connect an HDMI device with a mini HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1.5 meter long This cable works with Raspberry Pi Zero W. Dimensions: 1.5 meter Long
− +
-30%
WS2812 RGB Ring - 24 LED
$5.25 $7.50  
130 pc(s)
Round and round and round they go! 24 ultra bright smart RGB LED are arranged in a circle with 86mm outer diameter. The rings are 'chainable' - connect the output pin (DO) of one to the input pin (DI) of another. Use only one microcontroller pin to control as many as you can chain together!...
− +
-31%
Illuminated Capacitive Switch Module - Yellow
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
M12 (S-Mount) lens - 16mm (5 MegaPixels)
$9.95  
3 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 16mm fixed lens with IR Cut Filter...
− +
-20%
Arduino Sensor Kit (34 Sensor Modules)
$55.60 $69.50  
1 pc(s)
Note: For safety reasons and to comply with local government regulation, this kit does not contain any Laser Emitter and sensors containing Mercury. The sensor kit for the Arduino system consists of 34 individual sensor modules which can be used to carry out many interesting...
− +
Vibration Motor Module
$3.25  
16 pc(s)
This small vibratory motor module is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. The on-board MOSFET driver allows the module to interface directly to microcontroller. Features : Operating voltage:...
− +
Mini Lock-style Solenoid - 6VDC
$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
-20%
5" Resistive Touchscreen LCD For Pi 4
$60.40 $75.50  
12 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 5 inches 800x480 high resolution LCD display with resistive touchscreen and a HDMI adapter, engineered specifically to let you...
− +
NPN Transistors - 2N2222A
$0.50  
30 pc(s)
2N2222A is designed for high speed switching application at collector current up to 600mA, and feature useful current gain over a wide range of collector current, low leakage currents and low saturation voltage.
− +
-50%
Single Row Break Away Pin Header - Straight (Red)
$0.75 $1.50  
25 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
NPN Transistors - 45V 800mA (BC337)
$0.50  
677 pc(s)
This BC337 is a drop-in replacement for the 2N2222 Transistor This is the BC337, an NPN silicon BJT (Bipolar Junction Transistor). This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The BC337 is specifically rated...
− +
MQ-3 Gas Sensor (Alcohol)
$4.50  
3 pc(s)
This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to alcohol gas...
− +
Photo Interrupter Module (T-Shape)
$2.50  
5 pc(s)
This Photo Interrupter Module is widely used in motor speed detection, pulse count, the position limit, etc. It will trigger a signal when light between the sensor's gap is blocked. It works with 3.3V to 5VDC, and gives a HIGH on DO pin when the beam is blocked, and a LOW output when...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
1 2 3 4 5 6 7 8 9 10 11 12 13