Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11 12
6 - 13
Sort by Popularity
63 Per Page
-20%
Solder Leaded - 15-gram Tube
$2.55 $3.20  
1 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
Mini USB Microphone
$7.95  
2 pc(s)
This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with any computer, laptop, SBC, etc! Works great with a Raspberry Pi computer, but you can also use it with any other computer you want to record audio on. Simply plug it right in and...
− +
Magician Rover Chassis Kit v2
$29.90  
4 pc(s)
The Magician Rover Chassis v2 is our latest robot platform from Dagu. It features two gearmotors with 65mm wheels and a rear caster. The chassis plates are injection molded with a wide variety of mounting holes for sensors, controllers, power, etc. Simply bolt the two plastic platforms...
− +
M3 Nuts
$11.90  
1 pc(s)
1 bag of approximately 250 pcs M3 nuts. Compatible with all MakerBeam bolts
− +
MakerBeam 60 Degree Bracket (12 pcs)
$14.90  
7 pc(s)
The stainless steel 60 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 60 degree bracket
− +
-20%
3.5" Resistive Touchscreen LCD + Pre-configured 16GB microSD Card For RaspberryPi
$37.60 $47.00  
7 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 3.5 inches 480x320 high resolution LCD display with resistive touchscreen, engineered specifically to let you quickly attached the...
− +
3.3V Step-Up/Step-Down Voltage Regulator S7V8F3
$18.50  
6 pc(s)
The Pololu step-up/step-down voltage regulator S7V8F3 is a switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC converter) that uses a buck-boost topology. It takes an input voltage from 2.7 V to 11.8 V and increases or decreases the voltage to a fixed 3.3 V output...
− +
-20%
Servo - Generic Metal Gear (Micro Size)
$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...
− +
HC-06 Bluetooth Module
$16.80  
3 pc(s)
The HC-06 is a class 2 slave Bluetooth module designed for transparent wireless serial communication. Once it is paired to a master Bluetooth device such as PC, smart phones and tablet, its operation becomes transparent to the user. All data received through the serial input is immediately...
− +
Transceiver nRF24L01+ Module with PCB Antenna
$3.95  
7 pc(s)
This module based on Nordic nRF24L01+, a highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesiser and baseband logic including the Enhanced...
− +
Active Piezo Buzzer 3-24VDC Continuous Tone
$1.70  
Out-of-stock
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...
Out-of-stock
Mini Breadboard - Black
$1.75  
14 pc(s)
This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! Perfect for tiny projects and for sticking onto the top of Arduino...
− +
Flex Cable for Raspberry Pi Camera - 50cm
$3.95  
1 pc(s)
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 50cm long. Each order comes with one cable, Pi Camera...
− +
9V Battery Holder
$0.80  
6 pc(s)
This 9V battery holder allows your battery to snap in tight and holds it in place, which is great in situations where you don't want the battery just hanging. It also has three mounting holes so you can attach it securely to your enclosure. It is terminated with a 150mm leads
− +
Kitronik Edge Connector Breakout Board for BBC micro:bit
$8.90  
9 pc(s)
Looking to do more with your BBC micro:bit? Unlock its potential with this pre-built version of our Edge Connector Breakout Board! This breakout board has been designed to offer an easy way to connect additional circuits and hardware to the pins on the edge of the BBC micro:bit. It provides...
− +
Copper Tape - Conductive Adhesive, 5mm (20 Meters)
$4.95  
10 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
Flex Cable for Raspberry Pi Camera - 30cm
$3.50  
11 pc(s)
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 30cm long. Each order comes with one cable, Pi Camera...
− +
QTR-8A Reflectance Sensor Array
$15.00  
1 pc(s)
The QTR-8A reflectance sensor array is intended as a line sensor, but it can be used as a general-purpose proximity or reflectance sensor. The module is a convenient carrier for eight IR emitter and receiver (phototransistor) pairs evenly spaced at intervals of 0.375" (9.525 mm). Each...
− +
2-Pin JST Connector Kit
$0.50  
21 pc(s)
2-Pin 2mm pitch JST connector for battery holder or Lithium Polymer battery. Work with Sparkfun's Lipo charger/booster and Lilypad/Fio boards. Includes 2x female crimp pins 1x housing (2mm pitch)
− +
Cap Nuts M3 (50 pcs)
$9.50  
1 pc(s)
Cap nuts come in packages of 50 pieces. They will give your MakerBeam project an extra finish.
− +
Brass Sponge Solder Tip Cleaner
$7.95  
2 pc(s)
This is a brass sponge that will help clean your soldering iron tip. Use it to remove residue from your iron tip before soldering. It cleans better than conventional sponges and will not damage your iron tip. Made of low abrasive brass shavings, requires no water and won't cool down the tip.
− +
ESP8266 Wifi Module SMD
$8.90  
4 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...
− +
-20%
Load Cell - 1kg, Straight Bar
$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-31%
Panel Mount Toggle Switch - SPDT
$0.55 $0.80  
5 pc(s)
This heavy duty single-pole, double-throw (SPDT) toggle switch makes a great power switch or state selector for user interface. Rated for 6A at 125VAC. Includes a two threaded nuts and washer for mounting.
− +
Pulse Oximeter & Heart-Rate Sensor - MAX30102
$6.99  
4 pc(s)
MAX30102 Sensor is an integrated pulse oximetry and heart-rate monitor module. It is equipped with a red and IR LEDs as well as a very sensitive photon detector. The idea is to pulse the different LEDs, then detect what shines back. Based on the reflected signature it's possible to measure...
− +
-11%
Educational Traffic Light Module
$1.20 $1.35  
3 pc(s)
The Educational Traffic Light Module is a low cost hardware module designed to allow users to take their first steps into interfacing microcontroller with the real world. It is designed to remove many of the common hurdles people are faced with when getting started using hardware with the...
− +
1 x AA Battery Holder
$0.80  
3 pc(s)
Battery holder for single AA batteries, terminated with ~150mm leads
− +
2 x AAA Battery Holder with JST Connector
$1.40  
1 pc(s)
This 2xAAA Battery Cage with JST connector is compatible with the BBC micro:bit. Supplied with colour coded power leads and a JST connector at the end, this battery cage is light and features a M3 mounting hole in the centre so it can be attached to the back of BBC micro:bit cases. The JST...
− +
Protoboard, Double-Sided Pad-per-Hole, 3x7cm
$1.50  
4 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 3 x 7cm, 1.6mm thick
− +
Electret Microphone Amplifier - MAX9814 with Auto Gain Control
$14.00  
2 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret...
− +
Solder Leaded - 100-gram Spool
$9.95  
3 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 100 grams. Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
-11%
Non-Invasive Current Sensor - 30A
$15.50 $17.50  
1 pc(s)
This non-invasive current sensor (also known as a “split core current transformer”) can be clamped around the supply line of an electrical load to tell you how much current is passing through it. It does this by acting as an inductor and responding to the magnetic field around a...
− +
-20%
LilyPad Simple Power
$13.55 $16.95  
Out-of-stock
The LilyPad Simple Power is a simple e-textile board that lets you connect and charge a lipo battery and switch it on or off, that’s it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no...
Out-of-stock
-21%
Analog 2-axis Thumb Joystick with Select Button
$1.55 $1.95  
3 pc(s)
This kit makes it easy to mount a PS2-like thumb joystick to your project. The 2-axis joystick contains two independent potentiometers (~10k ohm, one per axis, ) for reporting the joystick's position and a 'press in to select' button. Since it's analog, you'll need two analog reading pins on...
− +
I2C 16x2 Character LCD Module - 5V
$15.95  
10 pc(s)
This is another great 16x2 character LCD display with I2C interface. As the pin resources of Arduino controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you...
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - Blue
$1.95  
2 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
-29%
10mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
22 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 10mm Documents : Datasheet
− +
MI:power board for the BBC micro:bit
$9.50  
3 pc(s)
When assembled, the MI:power board is connected directly to the 3V, GND and P0 connections on the micro:bit. The 3V and GND connections provide power to the micro:bit and the built in buzzer is connected to P0, which is the default output pin when using the audio functions in the Block Editor...
− +
-50%
3 x AA Battery Holder with Switch and Cover
$1.00 $2.00  
1 pc(s)
Enclosed battery holder for three AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-33%
Rocker Switch - SPST Medium
$0.60 $0.90  
2 pc(s)
This switch is about the same size as our Rocker Switch -DPDT except that it's single-pole single-throw. It's rated for 6A@250V / 10A@125VAC and can be snap-in panel mounted. Documents : Dimensional Drawings
− +
-20%
Load Cell - 5kg, Straight Bar
$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock
-40%
USB microB Cable - 1.5 meter
$3.00 $5.00  
1158 pc(s)
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
− +
Rubber Wheel For TT Gear Motor - 65mm Diameter
$1.95  
5 pc(s)
This Rubber Wheel For TT Gear Motor is equipped with a nice, thick rubber tread with excellent traction, and a press-fit design to make connecting super quick and easy. Note : This wheel is only for use with TT gearbox motors . Wheel body: 65 x 28mm
− +
MCP3002 - 2-Channel 10-Bit ADC With SPI Interface
$3.50  
39 pc(s)
The MCP3002 has a 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply 2 Channels...
− +
DC Barrel Power Jack/Connector
$0.50  
6 pc(s)
DC power jack / connector. This is a common barrel-type power jack for DC wall supplies. These are compatible with our DC wall supplies and have a 5.5mm jack, with a 2.1mm center pole diameter.
− +
DC & Stepper Motor HAT for Raspberry Pi
$38.00  
Out-of-stock
Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, this HAT uses...
Out-of-stock
2 Way Spring Clamp Terminal Block (Pack of 3)
$0.95  
16 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
Water Sensor - Large
$2.50  
2 pc(s)
This water sensor is designed to detect water, which can be used to sense water level and leakage. It works by using exposed copper traces to detect the presence of water droplets. The sensor board has a sensing area of 47 x 36mm. The on-board potentiometer is used to set the threshold for...
− +
Motor Driver Board v2 for the BBC micro:bit
$23.90  
7 pc(s)
This board provides a simple way to add motor driving capability to a BBC micro:bit. It allows two motors to be driven with full forward, reverse & stop control. It has terminal blocks to connect four input devices and a regulated 3V supply is fed in to the 80 way connector to power the...
− +
3-Pin Cable for Sharp Distance Sensors / SRF01 (w/Male Pin Header)
$2.90  
13 pc(s)
This 30cm cable has 26 AWG wires and a 3-pin female JST PH-style connector that works with Sharp Infra-red distance sensors: GP2Y0A02YK , GP2Y0A21YK and GP2Y0A41SK0F . The other ends of the wires are terminated with male pin header. The wire color scheme matches the Sharp distance sensor...
− +
-20%
Load Cell - 20kg, Straight Bar
$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
8 x AA Battery Holder with On/Off Switch and Cover
$3.80  
2 pc(s)
Enclosed battery holder for eight AA batteries. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
Mini Submersible Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
4 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This Mini Submersible Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with tubing....
− +
-29%
12mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet
− +
Thermoelectric Cooler - 40x40mm
$3.90  
3 pc(s)
Thermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. The Thermal Tape listed below works very...
− +
-20%
microSD Shield
$19.60 $24.50  
1 pc(s)
Running out of memory space in your Arduino project? The SparkFun microSD Shield equips your Arduino with mass-storage capability, so you can use it for data-logging or other related projects. Communication with microSD cards is achieved over an SPI interface. The SCK, DI, and DO pins of the...
− +
-20%
Load Cell - 10kg, Straight Bar
$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
WS2812 RGB LED Stick
$2.50  
1 pc(s)
This is the WS2812 Addressable RGB LED Stick with eight LEDs. The WS2812 is a addressable smart RGB LED that uses a single data line to control brightness and color. The embedded constant-currnet driver keeps the LED brightness consistent even if the input voltage varies. There are...
− +
Active Piezo Buzzer 3-24VDC Pulse Tone
$1.70  
5 pc(s)
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...
− +
-50%
Thermally Conductive Adhesive
$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...
− +
-50%
3 x AA Battery Holder
$0.50 $1.00  
84 pc(s)
Battery holder for three AA batteries, terminated with ~150mm leads
− +
-29%
12mm Panel Mount Momentary Pushbutton - Green
$0.60 $0.85  
6 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Adjustable Focus Lens
$39.00 $48.75  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
1 2 3 4 5 6 7 8 9 10 11 12
6 - 13