Delivery fee

New items

1 - 8
2 3 4 5 6 7 8 9 10 11 12 13
$9.95  
1 pc(s)
This nifty adapter cable with durable metal casing converts the digital HDMI video signals which are outputted from Raspberry Pi, into an analog signal required by the widely used VGA monitor. This adapter has an audio jack that provides stereo headphone/line out (HDMI 1.3 cables carry both...

$31.50 $35.00  
1 pc(s)
The Big Easy Driver, designed by Brian Schmalz , is a stepper motor driver board for bi-polar stepper motors up to 2A/phase. It is based on the Allegro A4983 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of...

$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...

$33.85  
1 pc(s)
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you...

$0.95  
16 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...

$0.95 $1.35  
126 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...

$0.60 $0.75  
5 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including...

$0.60 $0.75  
38 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1.5A@250VAC. Overall length (including...

$0.50 $0.75  
28 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...

$0.50  
35 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...

Roboteq 's HBL2360A is a high-current, dual channel controller for hall-sensor equipped Brushless DC motors. The controller uses the position information from the sensors to sequence power on the motors' 3 windings in order to generate smooth continuous rotation. The controller also uses...

$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 7mm Documents : Datasheet

$0.60 $0.85  
22 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 10mm Documents : Datasheet

$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet

$0.75  
9 pc(s)
This spring coil antenna is designed for the 433MHz devices. Each antenna is constructed of phosphor copper. Features: Frequency Range(MHz):433MHz +/-5MHz Gain(dBi):2.15 V.S.W.R:≤1.5@433M Input Impedance( OHM):50 Spring outer diameter: Wire diameter is 0.6mm,...

$0.60 $0.85  
6 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet

$4.20  
9 pc(s)
PIR sensors are used to detect motion from pets/humanoids from about 20 feet (~6 meters) away. This one has an adjustable delay before firing (approx 2-4 seconds) and adjustable sensitivity. You can easily reposition the sensor or mount it using the two holes on either side Runs on...

$3.50  
39 pc(s)
The MCP3002 has a 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply 2 Channels...

$14.20  
Out-of-stock
This Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the amplifier to your microcontroller you will be able to read the changes in the resistance of the load cell and with some calibration you'll be able...
Out-of-stock

$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...

$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...

$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...

$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock

$3.95 $7.90  
18 pc(s)
Our new capacitor kit comes with 10 each of 30 different capacitance values. All of these capacitors are packed into the zip-lock bags. This kit provides an easy way to build up a catalog of commonly used capacitors in a way that keeps them organised. Includes : Ceramic...

$2.00 $2.50  
46 pc(s)
This itty-bitty, shaftless vibratory motor is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. All moving parts are protected within the housing. With a 2.6-3.6V operating range, these units shake crazily at 3V. Once...

$5.50 $7.95  
1 pc(s)
The LilyPad Reed Switch is a simple breakout for a reed switch that will make it easy to use in e-textiles circuits in exactly the same manner that you can currently use the LilyPad Button and Switch. In order to make it more durable for wearable use, we've used a different style of reed switch,...

$2.50 $3.95  
1 pc(s)
This is a time saving kit of jumper wires - cut, stripped, and pre-bent for your prototyping pleasure. Included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each.

$7.90  
2 pc(s)
This DC motor controller allows you to control both the speed and direction of a DC motor without sacrificing torque. It can provides up to a maximum continuous current of 5A to your DC motor or other DC load using a Pulse Width Modulated (PWM) with a Duty cycle fully adjustable from 10%-100%....

$3.50  
2 pc(s)
Use this solder wick along with the solder sucker to clean up soldering messes. Wick really comes in handy when soldering or desoldering surface-mount parts.

$11.50  
2 pc(s)
Alcohol sensor is semiconductor sensor for alcohol detection. It has good sensitivity and fast response to alcohol, suitable for portable alcohol detector. Features : Power requirements: 5 VDC @ ~120 mA (heater on) Detection Gas: Alcohol Concentration: 20-1000ppm Alcohol Interface: 1 TTL...

$14.95  
2 pc(s)
This 434Mhz Wireless Transceiver Module is a new-generation multi-channel RF transceiver operating at the sub-GHz ISM bands from 433.4-473.0MHz,. The module supports up to 100 channels, with selectable RF power transmitter and highly sensitive RF receiver. Its output power level ranges from...

$0.50  
52 pc(s)
This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.

$0.50  
6 pc(s)
DC power jack / connector. This is a common barrel-type power jack for DC wall supplies. These are compatible with our DC wall supplies and have a 5.5mm jack, with a 2.1mm center pole diameter.

$9.95  
17 pc(s)
This is a handy little USB Bluetooth 4.0 dongle. Utilising the CSR8510 chipset, this dongle is backwards compatible with v2.1 and earlier, but also supports the latest v4.0 low energy bluetooth transmission. It has a maximum distance of up to 50m and includes an indicator LED. Use this Dongle...

$3.90  
3 pc(s)
Thermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. The Thermal Tape listed below works very...

$1.80  
3 pc(s)
This easy-to-use split ferrite core provides a cost-effective means to reduce the electromagnetic interference from being induced in or radiated from data and power cables. The special designed plastic housing allows the ferrite sleeve to use with a variety of cable diameters from 3 to 5mm...

$3.95  
7 pc(s)
This module based on Nordic nRF24L01+, a highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesiser and baseband logic including the Enhanced...

$14.50  
4 pc(s)
This D24V10F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 85% and 90% and has a very low dropout, so it can be used with input...

$14.00  
2 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret...

$39.00 $48.75  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...

$48.00 $60.00  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...

$2.50  
1 pc(s)
This is the WS2812 Addressable RGB LED Stick with eight LEDs. The WS2812 is a addressable smart RGB LED that uses a single data line to control brightness and color. The embedded constant-currnet driver keeps the LED brightness consistent even if the input voltage varies. There are...

$4.90  
3 pc(s)
This small stepper is a great way to get things moving, especially when positioning and repeatability is a concern. The stepper motor has five color-coded wires allow it to be controlled by both unipolar and bipolar stepper motor drivers. All five wires are used when connect to a unipolar...

$4.95  
1 pc(s)
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires...

$0.80  
3 pc(s)
Battery holder for single AA batteries, terminated with ~150mm leads

$3.80  
2 pc(s)
Enclosed battery holder for eight AA batteries. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$1.70  
Out-of-stock
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...
Out-of-stock

$0.80 $1.00  
Out-of-stock
Battery holder for two AA batteries, terminated with ~150mm leads
Out-of-stock

$0.80 $1.00  
7 pc(s)
Battery holder for two AAA batteries, terminated with ~150mm leads

$0.50 $1.00  
84 pc(s)
Battery holder for three AA batteries, terminated with ~150mm leads

$1.40  
19 pc(s)
Battery holder for six AA batteries, terminated with ~150mm leads

$1.50  
2 pc(s)
This is a simple Battery holder for eight AA cells arranged as two back-to-back four-cell holders.

$1.30  
21 pc(s)
Battery holder for five AA batteries, terminated with ~150mm leads

$2.90  
15 pc(s)
Enclosed battery holder for six AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$1.99  
Out-of-stock
This Single Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. Applications include solenoid valves, lamps, motors and other high current or high voltage devices. The modules are controlled with 5V signal and they are pre-soldered. A...
Out-of-stock

$3.99  
3 pc(s)
This two channels Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. The digital input circuit is optically isolated from the relay, so your controller is protected from voltage spikes and surges. The module is controlled with 5V...

$3.50  
118 pc(s)
This Rainbow Wire provides a convenient way to connect the signals in your projects. You can always pull the rainbow wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses. The color-coding can be used to organize power, ground and other signal types...

$2.80  
Out-of-stock
This is a 9V battery pack with on/off switch and terminated with a standard 5.5x2.1mm, center-positive barrel jack. Use this to battery-power your Arduino or other electronic projects. Battery & screw not included. Dimensions : 68mm x 33mm x 21mm Lead length: 12cm...
Out-of-stock

$3.50  
140 pc(s)
This Rainbow Wire provides a convenient way to connect the signals in your projects. You can always pull the rainbow wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses. The color-coding can be used to organize power, ground and other signal types...

$1.80 $2.00  
6 pc(s)
Enclosed battery holder for 9V battery. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$3.50  
8 pc(s)
This Rainbow Wire provides a convenient way to connect the signals in your projects. You can always pull the rainbow wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses. The color-coding can be used to organize power, ground and other signal types...

$1.00 $1.20  
23 pc(s)
Battery holder for four AA batteries, terminated with ~150mm leads

$0.60 $0.90  
2 pc(s)
This switch is about the same size as our Rocker Switch -DPDT except that it's single-pole single-throw. It's rated for 6A@250V / 10A@125VAC and can be snap-in panel mounted. Documents : Dimensional Drawings
1 - 8
2 3 4 5 6 7 8 9 10 11 12 13