Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11
5 - 13
Sort Alphabetically: A to Z
63 Per Page
-10%
Break Away Headers - 40-pin Male (Long Centered, PTH, 0.1")
$1.80 $2.00  
171 pc(s)
This is a row of 40 break away headers spaced 0.1" (2.54mm) apart with long pins on both sides. This header is especially useful when you need to connect a PCB to a solderless breadboard. Each header can be broken apart to your preference to fit custom PCBs or general custom headers.
− +
-50%
Break Away Headers - Right Angle
$1.00 $2.00  
1218 pc(s)
A row of right angle headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers.
− +
-50%
Breakout Board for BBC Micro:bit
$4.45 $8.90  
201 pc(s)
Unlock the potential of BBC Micro:bit with this assembled Breakout Board! This breakout board offers an easy way to connect additional circuits and hardware to the pins on the edge of the BBC micro:bit. It provides access to all of the BBC Micro:bit processor pins allowing a lot more extra...
− +
Breakout Board for Electret Microphone
$10.95  
2 pc(s)
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller's analog-to-digital converter. Each breakout comes fully assembled and works...
− +
Breakout Board for microSD w/Level Shifter
$11.90  
4 pc(s)
This Level Shifting microSD Breakout from Sparkfun is quite similar to the microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino's SD library's top speed on a 5V system. With this small breakout board, that is...
− +
Breakout Board for USB miniB
$3.95  
2 pc(s)
This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a miniUSB/USB miniB connector to your breadboard - here it is. Also good for an un-regulated, non-limited 5V supply up to 100mA.
− +
-15%
CAN-BUS Shield
$38.25 $45.00  
1 pc(s)
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output...
− +
Cap Nuts M3 (50 pcs)
$9.50  
1 pc(s)
Cap nuts come in packages of 50 pieces. They will give your MakerBeam project an extra finish.
− +
Capacitive Touch Breakout - AT42QT1011
$9.50  
2 pc(s)
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1011 SparkFun Capacitive Touch Breakout offers a single, momentary capacitive touch button with easy-to-use digital I/O pins. The AT42QT1011 is a dedicated,...
− +
Capacitor Ceramic 22pF
$0.20  
500 pc(s)
This is a very common 22pF capacitor. Used with crystals for loading purposes. 0.2" spaced leads make this a perfect candidate for breadboarding and perf boarding. Rated at 50V.
− +
-50%
Capacitor Kit (300 Total)
$3.95 $7.90  
18 pc(s)
Our new capacitor kit comes with 10 each of 30 different capacitance values. All of these capacitors are packed into the zip-lock bags. This kit provides an easy way to build up a catalog of commonly used capacitors in a way that keeps them organised. Includes : Ceramic...
− +
Circuit Explorer for BBC Micro:bit
$10.95  
6 pc(s)
Introducing the new Circuit Explorer for BBC Micro:bit from SGBotic. This breakout board offers an easy way to connect additonal circuit and sensors to the micro:bit using the crocodile clips and copper tape. The back of the Circuit Explorer is made flat so that it can stick to any clean...
− +
Coin Acceptor - Programmable 4 Coin Type
$59.95  
2 pc(s)
Your project may be free-as-in-speech, but that doesn't mean it has to be free-as-in-beer. This handy coin validator/acceptor module is just like the ones you've seen in arcades. This model has the cool ability to accept up to 4 different coins! For example, you can program it for 4...
− +
Cool White LED Flexi-Strip - 5V (Bare, 5 meters)
$36.00  
3 pc(s)
These single color LED strip feature 60 ultra bright cool white LEDs on one meter. As these are bare LED strips that have no protective coating, your project won't be water proof but there is access to each LED and each strip length can be easily modified. Each of these strips need a 3V to 5V...
− +
Copper Tape - 10mm (20 Meters)
$5.99  
9 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is...
− +
Copper Tape - 50mm (20 Meters)
$26.95  
5 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is...
− +
Copper Tape - 5mm (20 Meters)
$3.95  
6 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is...
− +
Copper Tape - Conductive Adhesive, 10mm (20 Meters)
$6.90  
Out-of-stock
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
Out-of-stock
Copper Tape - Conductive Adhesive, 50mm (20 Meters)
$29.95  
5 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
Copper Tape - Conductive Adhesive, 5mm (20 Meters)
$4.95  
10 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
Corner Cube Kit For MakerBeamXL - Black
$25.70  
3 pc(s)
This Corner Cubes can join up to three MakerBeamXL in right angle. Corner Cubes are joined with a beam by the threaded beam ends. Each set contains 12 15mmx15mmx15mm cubes Note : Not compatible with 10mmx10mm MakerBeam.
− +
Corner Cube Kit For MakerBeamXL - Clear
$25.70  
2 pc(s)
This Corner Cubes can join up to three MakerBeamXL in right angle. Corner Cubes are joined with a beam by the threaded beam ends. Each set contains 12 15mmx15mmx15mm cubes Note : Not compatible with 10mmx10mm MakerBeam.
− +
DC & Stepper Motor HAT for Raspberry Pi
$38.00  
Out-of-stock
Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, this HAT uses...
Out-of-stock
DC Barrel Jack Adapter - Female
$2.50  
4 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might be the simple solution.
− +
DC Barrel Jack Adapter - Male
$2.50  
36 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution.
− +
DC Barrel Jack Plug - Female
$0.50  
39 pc(s)
This female barrel jack plug is great for adding a common connector to the end of wires. This jack is compatible with 5.5x2.1mm barrel connectors. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.
− +
DC Barrel Jack Plug - Male
$0.50  
52 pc(s)
This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.
− +
DC Barrel Power Jack/Connector
$0.50  
6 pc(s)
DC power jack / connector. This is a common barrel-type power jack for DC wall supplies. These are compatible with our DC wall supplies and have a 5.5mm jack, with a 2.1mm center pole diameter.
− +
DC Motor Driver HAT(V1.0) for Raspberry Pi
$24.95  
Out-of-stock
This is a Raspberry Pi DC motor driver board with on-board encoder interface, which can drive 2-way DC motor and DC motor with encoder. It communicates with Raspberry Pi via I2C, easy to configure and drive motors. The DC Motor Driver HAT adopts STM32 micro processor to analyze the command...
Out-of-stock
DE-SWADJ Step Down Adjustable Switching Regulator - 10W
$24.50  
2 pc(s)
The DE-SWADJ is the adjustable version of our SW0XX step down voltage regulators. It is designed to be the easiest possible way to add an adjustable voltage source to a new or existing project with all the efficiency benefits of switch-mode power. The DE-SWADJ is pin-compatible with the...
− +
DE-SWADJ3 Step Down Adjustable Switching Regulator 25W
$42.00  
6 pc(s)
The DE-SWADJ 3 is a larger version of our DE-SWADJ adjustable step down voltage regulator. Previously it was necessary to put multiple DE-SWADJ units in parallel to achieve ratings over 1A, which was bulky, expensive and carried with it a considerable increase in dropout voltage. The...
− +
DELink 2 USB Link For Kangaroo PID Motion Controller
$35.00  
4 pc(s)
The DELink 2 USB Link is the perfect compliment to our Kangaroo x2 self-tuning PID motion controller. Coupled with the DEScribe software, you can upload / download settings or reset the Kangaroo to factory defaults. Utilizing the easy-to-use USB bus, changing the settings on your Kangaroo...
− +
Diagonal Cutters
$5.80  
3 pc(s)
Mini Diagonal Cutters. These are great little cutters! A must have for clipping leads and extra solder tails. 4" long.
− +
Diaphragm Liquid Pump (6V to 12VDC)
$4.50  
10 pc(s)
Looking for a battery powered liquid pump? This non-submersible diaphragm liquid pump will operates between DC 6V to 12V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. Each diaphragm liquid pump comes with a pair of...
− +
Diffused Blue LED - 5mm (10 pcs)
$1.00  
118 pc(s)
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a blue lens. It has a typical forward voltage of 3.1V and a rated forward current of 20mA. Pack of 10 diffused blue LEDs....
− +
Diffused Green LED - 10mm (5 pcs)
$1.00  
1 pc(s)
Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Pack of 5 diffused green LEDs. Features : 520-525nm Green 3.0-3.4VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 150-180...
− +
Diffused Green LED - 5mm (10 pcs)
$1.00  
85 pc(s)
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a green lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA. Pack of 10 diffused green LEDs....
− +
Diffused Red LED - 5mm (10 pcs)
$1.00  
9 pc(s)
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a green lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA. Pack of 10 diffused red LEDs....
− +
Diffused Yellow LED - 10mm (5 pcs)
$1.00  
13 pc(s)
Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Pack of 5 diffused Yellow LEDs. Features : 620-625nm Red 1.8-2.2VDC Forward Voltage 20mA Forward Current 40 degree viewing angle 100-150...
− +
Diffused Yellow LED - 5mm (10 pcs)
$1.00  
26 pc(s)
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a yellow lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA. Pack of 10 diffused yellow LEDs....
− +
Digital PWM Motor Speed Controller - 5A
$7.90  
2 pc(s)
This DC motor controller allows you to control both the speed and direction of a DC motor without sacrificing torque. It can provides up to a maximum continuous current of 5A to your DC motor or other DC load using a Pulse Width Modulated (PWM) with a Duty cycle fully adjustable from 10%-100%....
− +
Diode Rectifier - 1A 50V
$0.20  
772 pc(s)
This is a simple, very common rectifier diode. Often used for reverse voltage protection, the 1N4001 is a staple for many power, DC to DC step up, and breadboard projects. 1N4001 is rated for up to 1A/400V. Documents: Datasheet
− +
DIP Switch - 1 Position
$0.50  
2 pc(s)
A simple 1-position DIP switch - fits great into a breadboard! Works great as general control switches.
− +
DIP Switch - 2 Position
$0.35  
42 pc(s)
DIP switch with 2 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
− +
DIP Switch - 3 Position
$0.40  
17 pc(s)
DIP switch with 3 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
− +
DIP Switch - 4 Position
$0.45  
Out-of-stock
DIP switch with 4 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
Out-of-stock
DIP Switch - 5 Position
$0.60  
22 pc(s)
DIP switch with 5 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
− +
DIP Switch - 6 Position
$0.60  
36 pc(s)
DIP switch with 6 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
− +
DIP Switch - 8 Position
$0.65  
26 pc(s)
DIP switch with 8 individual switch positions. The pins have 2.54mm spacing - fits great into a breadboard! Works great as general control switches.
− +
DRV8825 Stepper Motor Driver Carrier, High Current
$26.95  
7 pc(s)
The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section...
− +
DRV8833 Dual Motor Driver Carrier
$18.00  
3 pc(s)
This tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair of DC motors. With an operating voltage range from 2.7 to 10.8 V and built-in protection against reverse-voltage, under-voltage, over-current, and...
− +
Dual MAX14870 Motor Driver for Raspberry Pi
$42.00  
4 pc(s)
This motor driver expansion board and its corresponding Python library make it easy to control a pair of bidirectional, brushed DC motors with a compatible Raspberry Pi (Model B+ or newer), including the Pi 3 Model B+ and Model A+. The expansion board features two MAX14870 H-bridge motor...
− +
Dynamic Shunt Regulator (SR5K100V25R)
Contact us for details

 
 
The SR5K Shunt Regulator is a protection subsystem for dissipating the regenerative energy when braking or drastically reducing the speed of electric motors. During braking, the regenerative voltage can equal to or even exceed the supply voltage in some cases depending on the rotational inertia...
-11%
Educational Traffic Light Module
$1.20 $1.35  
3 pc(s)
The Educational Traffic Light Module is a low cost hardware module designed to allow users to take their first steps into interfacing microcontroller with the real world. It is designed to remove many of the common hurdles people are faced with when getting started using hardware with the...
− +
EE Component Pack #1
$29.50  
1 pc(s)
This is a custom made component kit for the following NUS Executive Education program: Architecting IoT Solutions Design Intelligent Edge Computing The kit includes: 1x Breadboard Medium Self-Adhesive, 830 tie-in points 1x 40-Pin Rainbow Wire, 20cm - M/F...
− +
Electret Microphone Amplifier - MAX4466 with Adjustable Gain
$13.00  
5 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier...
− +
Electret Microphone Amplifier - MAX9814 with Auto Gain Control
$14.00  
2 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret...
− +
-20%
Electric Paint Lamp Kit
$48.00 $60.00  
6 pc(s)
Make three paper lamps with no tools, no programming, no special skills required. A great gift for anyone that needs more light in their life! Transform a piece of paper into a beautiful lamp in three easy steps. Paint, plug, and play! Use this Electric Paint to create custom...
− +
ESP32 Development Board
$19.95  
2 pc(s)
The ESP32 Development Board is a low-footprint, minimal system development board powered by ESP-WROOM-32 module. The ESP-WROOM-32 is a powerful and compact module that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...
− +
ESP32 Development Board Lite
$15.95  
4 pc(s)
The ESP32 Development Board Lite is a compact version of standard ESP32 development board. Like other ESP32 boards, it has a 32-bit dual core microcontroller that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...
− +
ESP32 Development Board U.FL w/Antenna
$23.50  
14 pc(s)
The ESP32 Development Board is a low-footprint, minimal system development board powered by ESP-WROOM-32 module. The ESP-WROOM-32 is a powerful and compact module that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...
− +
ESP8266 WiFi Module Adaptor w/Logic Level Converter
$4.30  
8 pc(s)
This ESP8266 WiFi Module Adapter allows easy interfacing of ESP8266 WiFi Module to Arduino Uno / Mega or any development board running on 5V logic. It features onboard LDO regulator to supply 3V to ESP8266 WiFi Module and logic level converter for both Tx and Rx pins. Note :...
− +
ESP8266 WiFi Module Breakout Board
$2.40  
30 pc(s)
This ESP8266 WiFi Module Breakout Board allows you to take the dual row header of the ESP-01 and make it breadboard friendly. This board comes with the header and decoupling capacitor presoldered, but requires you to solder on the male pins. NOTE : ESP8266 WiFi Module not included.
− +
1 2 3 4 5 6 7 8 9 10 11
5 - 13