Delivery fee

New items

1 2 3 4 5 6 7 8 9 10
4 - 13
Sort Alphabetically: Z to A
63 Per Page
-50%
SSOP to DIP Adapter 20-Pin
$1.95 $3.90  
5 pc(s)
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm)....
− +
SRF05 Low Cost Ultrasonic Range Finder w/Header
$28.90  
2 pc(s)
The SRF05 is an evolutionary step from the SRF04, and has been designed to increase flexibility, increase range, and to reduce costs still further. As such, the SRF05 is fully compatible with the SRF04. Range is increased from 3 meters to 4 meters. A new operating mode (tying the mode...
− +
SRF02 Low Cost Single Transducer Ultrasonic Range Finder
$23.80  
Out-of-stock
The SRF02 is a single transducer ultrasonic rangefinder in a small footprint PCB. It features both I2C and a Serial interfaces. The serial interface is a standard TTL level UART format at 9600 baud,1 start, 2 stop and no parity bits, and may be connected directly to the serial ports on...
Out-of-stock
Split Ferrite Cable Core For RFI / EMI Noise Suppression
$1.80  
3 pc(s)
This easy-to-use split ferrite core provides a cost-effective means to reduce the electromagnetic interference from being induced in or radiated from data and power cables. The special designed plastic housing allows the ferrite sleeve to use with a variety of cable diameters from 3 to 5mm...
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +
-15%
SPDT Mini Power Switch
$1.95 $2.30  
19 pc(s)
Simple SPDT slide switch. Rated at 30V/200mA. The pins have .1" spacing - fits great into a breadboard! Use it as a power switch or general control switch. Documents : Dimensional Drawing
− +
-20%
Sparkfun XBee Wireless Shield
$19.95 $24.95  
1 pc(s)
Xbee radios are an awesome way to add wireless capability to your Arduino project and now it's even easier with the XBee Shield. The shield form-factor mates directly with any dev board that has an Arduino standard footprint and equips it with wireless communication capabilities using the...
− +
-10%
SparkFun Thing Plus - Artemis
$30.15 $33.50  
1 pc(s)
If you are looking for a board that (almost) does it all, look no further! The SparkFun Artemis Thing Plus takes the popular Thing Plus footprint and adds in the powerful Artemis module for ultimate functionality. Fully compatible with SparkFun's Arduino core, the modern USB-C connector makes...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
SparkFun RedBoard Artemis Nano
$26.50  
1 pc(s)
We like to joke the Artemis Nano is a party on the front and business on the back. And that's by design! All the important LEDs, connectors, labels, and buttons are presented on the front for the best user experience with all the supporting circuitry on the rear of the board. The RedBoard...
− +
-14%
SparkFun RedBoard Artemis
$28.00 $32.50  
1 pc(s)
Think of the SparkFun RedBoard Artemis as just another Arduino....that has BLE, one megabyte of flash, and runs at less than 1mA. And, it can run TensorFlow models too! The RedBoard Artemis takes the incredibly powerful Artemis module from SparkFun and wraps it up in an easy to use and...
− +
-10%
SparkFun Photodetector Breakout - MAX30101 (Qwiic)
$30.15 $33.50  
3 pc(s)
The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light...
− +
SparkFun OpenScale
$50.50  
4 pc(s)
The SparkFun OpenScale is a simple-to-use, open source solution for measuring weight and temperature. It has the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision. Simply...
− +
-25%
SparkFun Motor Driver - Dual TB6612FNG (with Headers)
$14.65 $19.55  
8 pc(s)
The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled,...
− +
-50%
SparkFun moto:bit
$22.50 $45.00  
4 pc(s)
The SparkFun moto:bit is a fully loaded "carrier" board for the micro:bit that, when combined with the micro:bit, provides you with a fully functional robotics platform. The moto:bit offers a simple, beginner-friendly robotics controller capable of operating a basic robotics chassis. Onboard...
− +
-50%
SparkFun gator:bit
$15.50 $31.00  
4 pc(s)
The SparkFun gator:bit is an all-in-one "carrier" board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pin on the micro:bit is broken out to pads that alligator (or crocodile, if you prefer) clips so you can get the most out of...
− +
Solderless Adapter For WS2812 Fexi-Strip
$2.95  
19 pc(s)
This solderless adapter provides a convenient way to connect the WS2812 LED strip to your microcontroller. Although soldering is the best way to maintain a lasting connection, the solderless adapter is a great way to get your project going quickly without the hassle of soldering work. When...
− +
Soldering Iron Stand
$9.90  
3 pc(s)
This is a simple soldering iron stand with heavy base for excellent stability. A cleaning sponge is included. Note: Not compatible with TOL-01027
− +
Solder Wick - 1.5m Spool
$3.50  
2 pc(s)
Use this solder wick along with the solder sucker to clean up soldering messes. Wick really comes in handy when soldering or desoldering surface-mount parts.
− +
-20%
Solder Leaded - 15-gram Tube
$2.55 $3.20  
1 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
Solder Leaded - 100-gram Spool
$9.95  
3 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 100 grams. Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
Solder Lead Free - 15-gram Tube
$5.90  
5 pc(s)
This is you basic tube of unleaded (Pb-free) solder with a 60/40 no clean, water soluble resin core. 0.031" gauge and 15 grams. Mix: 96.5% tin / 3.0% silver / 0.5% copper
− +
-10%
Solder Lead Free - 100-gram Spool
$12.50 $13.95  
1 pc(s)
This is your basic spool of lead free solder with a water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced users that should last 6-12 months depending on how often you solder. If you are just beginning to solder, we recommend you order the...
− +
-50%
Solar Panel - 18V 2.5W
$18.75 $37.50  
2 pc(s)
Need a clean energy source to power you project? Check out this high quality, high output solar panel. Each panel features high efficient polycrystalline cells mounted onto a fibreglass PCB and covered with epoxy resin which protect the cells without reducing efficiency. A weatherproof plastic...
− +
Soil Moisture Sensor - Long Probe
$9.90  
Out-of-stock
This Soil Moisture Sensor is used to measure the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two long exposed metal rods function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil...
Out-of-stock
Soil Moisture Sensor
$3.50  
10 pc(s)
This soil moisture sensor can read the amount of moisture present in the soil surrounding it. It's a low tech sensor, but ideal for monitoring an urban garden, or your pet plant's water level. This is a must have tool for a connected garden! This sensor uses the two probes to pass...
− +
Soil Moisture /Temperature Sensor - SHT10
$29.95  
1 pc(s)
Take your gardening project to the next level with a SHT-10 based soil sensor. The sensor includes a temperature/humidity sensor module from Sensiron in a sinter metal mesh encasing. The casing is weatherproof and will keep water from seeping into the body of the sensor and damaging it, but...
− +
-20%
SOIC to DIP Adapter 8-Pin
$3.95 $4.95  
1 pc(s)
The SparkFun 8-Pin SOIC to DIP Adapter is a small PCB that lets you adapt SOIC packages into a DIP footprint. These tiny boards are useful for modding and upgrading devices that use 8-pin DIP ICs, when the upgraded IC is only available in a SOIC footprint. You can also use these adapters for...
− +
-50%
SOIC to DIP Adapter 28-Pin
$3.15 $6.30  
22 pc(s)
Low-cost basic SOIC break out boards. These are custom PCB boards that interface standard SOIC devices to standard .1" (2.54mm) headers. 28-SOIC: Standard .6" spacing between pins. Will fit directly into a standard width (600 mil) DIP socket. For wide ICs (memories, drivers, 74s,...
− +
-30%
SMC04 High-Power Motor Controller w/Feedback
$88.00 $125.00  
1 pc(s)
The SMC04 high-power motor controller with feedback has multiple interface and feedback options that simplify servo control of commonly available DC motors. T he module features three independent interfaces: a serial protocol for microcontroller-based applications, a pulse-width...
− +
Smart Dust Sensor - SM-PWM-01C
$19.90  
5 pc(s)
This is a dust sensor that detects the dust particle concentration in air by using optical sensing method. An infrared light emitting diode (IR LED) and a photo-sensor are optically arranged in the device. The photo-sensor detects the reflected IR LED light by dust particles in air. The...
− +
Small Wheel For Toy Motor - 28mm Diameter
$0.50  
8 pc(s)
This custom-designed plastic wheel has a rubber ring measuring 28mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø28 x 3.8mm
− +
Small Wheel For Toy Motor - 17.5mm Diameter
$1.50  
14 pc(s)
This custom-designed plastic wheel has a rubber tire measuring 17.5mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø17.5 x 6.5mm
− +
-20%
Small Stepper Motor
$11.60 $14.50  
1 pc(s)
These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. Features : Stride Angle (degrees) : 7.5 2-Phase Rated Voltage : 12V Rated Current : 400mA 3mm Diameter Drive Shaft...
− +
Slip Ring - 6 Wire (2A)
$18.95  
5 pc(s)
This is a 6 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an...
− +
Slip Ring - 12 Wire (2A)
$18.95  
1 pc(s)
This is a 12 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an...
− +
-50%
Single Row Break Away Pin Header - Straight (Yellow)
$0.75 $1.50  
240 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Pin Header - Straight (White)
$0.75 $1.50  
15 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Pin Header - Straight (Red)
$0.75 $1.50  
25 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Pin Header - Straight (Blue)
$0.75 $1.50  
135 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Pin Header - Straight (Black)
$0.75 $1.50  
119 pc(s)
A row of headers - break to fit. 40 pins that can be cut to any size. Used with custom PCBs or general custom headers. Features: Pin Style: Square Number of Pins: 40 Pin Spacing: 0.1" (2.54 mm) Pin Length: 11.5 mm
− +
-50%
Single Row Break Away Female Header
$0.75 $1.50  
273 pc(s)
Single row of 40-holes, female header. Can be cut to size with a pair of wire-cutters. Standard .1" spacing. We use them extensively in the Olimex development boards. They mate very well with break away headers. Please note: You will probably lose one pin with each cut....
− +
Single Channel Relay Module (5V)
$1.99  
Out-of-stock
This Single Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. Applications include solenoid valves, lamps, motors and other high current or high voltage devices. The modules are controlled with 5V signal and they are pre-soldered. A...
Out-of-stock
Sharp Infrared Distance Sensor GP2Y0A41SK0F - 4 to 30cm
$12.00  
23 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 3.1V at 4cm to 0.3V at 30cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor. See 3-pin Cable for Sharp Sensors...
− +
Sharp Infrared Distance Sensor GP2Y0A21YK - 10 to 80cm
$12.70  
2 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 3.1V at 10cm to 0.3V at 80cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor - see 3-pin cable for Sharp Sensors...
− +
Sharp Infrared Distance Sensor GP2Y0A02YK - 20 to 150cm
$16.80  
5 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 2.5V at 20cm to 0.4V at 150cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor. See 3-pin Cable for Sharp Sensors...
− +
Sharp Digital Distance Sensor - 5cm
$14.95  
8 pc(s)
The  GP2Y0D805  and  GP2Y0D810  are Sharp’s smallest and fastest distance sensors. With a sample rate of almost 400 Hz and a sensing distance to 5 cm or 10 cm, respectively, these sensors provides attractive alternatives to shorter-range ...
− +
-50%
Shaft - Solid 2mm Diameter x 90mm
$0.10 $0.20  
33 pc(s)
These 90mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 80mm
$0.10 $0.20  
19 pc(s)
These 80mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 75mm
$0.10 $0.20  
2 pc(s)
These 75mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 60mm
$0.10 $0.20  
12 pc(s)
These 60mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 40mm
$0.10 $0.20  
30 pc(s)
These 40mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 30mm
$0.10 $0.20  
14 pc(s)
These 30mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 20mm
$0.10 $0.20  
33 pc(s)
These 20mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 110mm
$0.10 $0.20  
5 pc(s)
These 110mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
-50%
Shaft - Solid 2mm Diameter x 100mm
$0.10 $0.20  
12 pc(s)
These 100mm long steel shafts have a diameter of 2mm. These shafts are solid, which makes them an ideal choice for axles. They fit on the following wheel and pulley: Wheel: RBT-02709 RBT-02711 RBT-02713 Pulley: RBT-02714 RBT-02715...
− +
SGBotic Ultimate SR04 RGB Ultrasonic Sensor - I2C
$13.95  
Out-of-stock
Based on the design of the popular HC-SR04, SGBotic Ultimate SR04 RGB Ultrasonic Sensor offers some interesting features in addition to the solid performance of the classic HC-SR04. This sensor improves on the classic by adding a microcontroller to process the information gathered by the...
Out-of-stock
SGBotic Paper Circuits Kit w/Sound Card
$14.95  
Out-of-stock
SGBotic Paper Circuits kit let you learn the basics and fundamentals of an electric circuit in a fun way! Using circuit template cards, LEDs, sound card, speaker, copper tape and coin cell batteries, you will create four circuits: simple, series, parallel and sound circuits. No prior electronics...
Out-of-stock
-10%
SGBotic Micro:bit Starter Kit (w/BBC micro:bit v2.2)
$62.95 $69.95  
2 pc(s)
If you are a beginner looking to learn programming and electronics, look no further than this SGBotic Micro:bit Starter Kit. This kit is designed to introduce programming and basic electronic interfacing to a user with absolutely no experience in these areas. It contains everything you need...
− +
SGBotic Micro:bit Robot Board
$19.95  
7 pc(s)
SGBotic Micro:bit Robot Board is designed for development of an autonomous obstacle avoidance robot or line following robot using BBC micro:bit . This Robot Board is capable of driving two DC motors. It has a dedicated port for HC-SR04 Ultrasonic Sensor and Line Follower Array . The...
− +
SGBotic EDUKIT2 For Arduino
$65.00  
Out-of-stock
Interested in learning to work with Arduino but not sure where to start? This EDUKIT2 is a great way for you to get started with programming and hardware interaction with the Arduino Uno board. The kit includes the latest Arduino Uno R3 (Italy), breadboard, jumper wires, sensors, and other...
Out-of-stock
SGBotic EduFun Buggy for Micro:bit (rev.B)
$59.95  
Out-of-stock
SGBotic EduFun Buggy for Micro:bit is designed for learning basic robotics using BBC Micro:bit and MakeCode graphical programming. Although this kit is targeted for beginners with no prior robotic experience, experienced users will find it useful and fun too. The kit includes all parts required...
Out-of-stock
Servo Shield For OpenMV Cam
$25.95  
2 pc(s)
The Servo Shield gives your OpenMV Cam the ability to control up to 8 servos in parallel. It features the PCA9685 Servo Controller which can also do general-purpose PWM. We've got a PCA9685.py script for controlling the chip for general-purpose PWM and a Servo.py script for controlling...
− +
1 2 3 4 5 6 7 8 9 10
4 - 13