Delivery fee

New items

1 - 9
3 4 5 6 7 8 9 10 11 12 13
Sort by Price: Low to High
63 Per Page
Temperature Sensor - Waterproof (DS18B20) w/Interface Board
$12.90  
7 pc(s)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a...
− +
Basic 20x4 Character LCD - Black on Green 5V
$12.95  
2 pc(s)
This is a basic 20 character by 4 line display. Utilizes the extremely common HD44780 parallel interface chipset ( datasheet ). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes LED backlight. Dimensions: 3.86 x 2.36 x...
− +
WS2812B RGB Matrix - 8x8 (64 LED)
$12.99  
6 pc(s)
This is the RGB LED matrix panel with 64 WS2812B LEDs arranged in an 8x8 matrix. Each LED is capable of drawing as much as 60mA (at peak brightness the matrix can draw just over 3.5 Amps at 5 Volts), this adds up so it is suggested to use a 5V 2A power supply. For most uses, you'll see about...
− +
Electret Microphone Amplifier - MAX4466 with Adjustable Gain
$13.00  
5 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier...
− +
-15%
PIR Motion Sensor
$13.20 $15.50  
5 pc(s)
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low. Red wire is power (5 to 12V). White wire is GND. Black wire is open collector Alarm....
− +
-50%
Transceiver nRF2401A with Chip Antenna
$13.25 $26.50  
3 pc(s)
This nRF2401A module has the same minimum interface of 7 pins (all in a .1" spaced connector) as the original nRF2401A module, but the size is reduce by over 60%! These are the nRF2401A 2.4GHz transceiver modules with built in chip antenna designed around the Nordic Semiconductor nRF2401A...
− +
MakerBeam Right Angle Bracket (12 pcs)
$13.50  
2 pc(s)
The stainless steel right angle bracket is a great addition to MakerBeam product range. The right angle brackets give you the possibilty to place one beam on top of the other. Includes 12x Stainless steel right angle bracket
− +
MakerBeam L-Bracket 90 Degree (12 pcs)
$13.50  
6 pc(s)
The stainless steel corner bracket is a great addition to MakerBeam product range.Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 90 degree L-bracket
− +
-50%
micro:Gamepad
$13.50 $27.00  
10 pc(s)
Micro:bit gamepad is an expansion gamepad based on micro:bit. You only need to plug in the micro:bit, it will turn into a wireless remote controller a wireless game console. This product packaged with acrylic plate, that giving it a good feel and no longer feels like a bare circuit...
− +
MakerBeam Straight Bracket (12 pcs)
$13.50  
4 pc(s)
The stainless steel straight bracket is a great addition to MakerBeam product range. We are sure you love it too since customers regularly asked for it! Includes 12x Stainless steel Straight Bracket
− +
Assembled Pi T-Expansion Kit for Raspberry Pi (w/Color-Coded Ribbon Cable)
$13.50  
11 pc(s)
This Pi T-Expansion Kit comes with a small board that connects to the 40-pin GPIO connector on the Raspberry Pi B+ and Pi2 /3 /3+, and breaks the pins out to breadboard-friendly arrangement and spacing. The Kit comes with a 40 pin ribbon cable, and an already soldered T-Expansion as shown....
− +
MakerBeam T-Bracket (12 pcs)
$13.50  
4 pc(s)
The stainless steel T-bracket is a great addition to MakerBeam product range. It is compatible with both threaded and non-threaded MakerBeam. Includes 12x Stainless steel T-Bracket
− +
-20%
LilyPad Simple Power
$13.55 $16.95  
Out-of-stock
The LilyPad Simple Power is a simple e-textile board that lets you connect and charge a lipo battery and switch it on or off, that’s it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no...
Out-of-stock
RGB color Sensor With IR Filter & LED - TCS34725
$13.70  
Out-of-stock
The TCS34725 is probably the best color sensor on the market. It has a high sensitivity, wide dynamic range RGB and Clear light sensing elements. An integrated IR blocking filter minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. The...
Out-of-stock
Adafruit Triple-axis Magnetometer - MMC5603 - STEMMA QT / Qwiic
$13.80  
1 pc(s)
Sense the magnetic fields surrounding us with this handy triple-axis magnetometer (compass) module. Magnetometers can sense where the strongest magnetic force is coming from, generally used to detect magnetic north, but can also be used for measuring magnetic fields. This sensor tends to be...
− +
SGBotic Ultimate SR04 RGB Ultrasonic Sensor - I2C
$13.95  
Out-of-stock
Based on the design of the popular HC-SR04, SGBotic Ultimate SR04 RGB Ultrasonic Sensor offers some interesting features in addition to the solid performance of the classic HC-SR04. This sensor improves on the classic by adding a microcontroller to process the information gathered by the...
Out-of-stock
Electret Microphone Amplifier - MAX9814 with Auto Gain Control
$14.00  
2 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret...
− +
-30%
microSD Card - 64GB (Class 10, UHS-I )
$14.00 $20.00  
9 pc(s)
This is a class 10 64GB microSD memory card, perfect for housing operating systems for single board computers and a multitude of other information. Since this is a class 10 UHS-I microSD it is capable of transferring data at speeds up to 100MB/s allowing it to have a noticeable increase in...
− +
Load Cell Amplifier - HX711
$14.20  
3 pc(s)
This Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the amplifier to your microcontroller you will be able to read the changes in the resistance of the load cell and with some calibration you'll be able...
− +
M5Stack Stackable Module - Servo
$14.50  
4 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Stackable Servo module is designed for quick prototyping of servo motor project. It can supports up to 12 servo motors. The on-board MEGA328...
− +
Sunflower Solar Power Manager 5V
$14.50  
3 pc(s)
Solar Power Manager 5V is a small power and high-efficiency solar power management module designed for 5V solar panel. It features as MPPT (Maximum Power Point Tracking) function, maximizing the efficiency of the solar panel. Apart from serving as a solar charger, the module can provide up to...
− +
3.3V, 1A Step-Down Voltage Regulator D24V10F3
$14.50  
5 pc(s)
This D24V10F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.3V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 80% and 90% and has a very low dropout, so it can be used with input...
− +
12V, 1A Step-Down Voltage Regulator D24V10F12
$14.50  
4 pc(s)
This D24V10F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 85% and 90% and has a very low dropout, so it can be used with input...
− +
-25%
SparkFun Motor Driver - Dual TB6612FNG (with Headers)
$14.65 $19.55  
8 pc(s)
The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled,...
− +
Serial Wifi Module (Support MQTT) - 3V
$14.90  
1 pc(s)
The Serial To WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The onboard ESP-12F ESP8266 module is capable of either hosting an application or offloading all Wi-Fi networking functions from another...
− +
MakerBeam 45 Degree Bracket (12 pcs)
$14.90  
6 pc(s)
The stainless steel 45 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 45 degree bracket
− +
MakerBeam 60 Degree Bracket (12 pcs)
$14.90  
7 pc(s)
The stainless steel 60 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 60 degree bracket
− +
Analog Capacitive Soil Moisture Sensor- Corrosion Resistant
$14.90  
2 pc(s)
This product measures soil mositure levels by capacitive sensing, rather than resistive sensing like other types of moisture sensor. It is made of a corrosion resistant materal giving it a long service life. Insert it into soil and impress your friends with the real-time soil moisture data!...
− +
USB WiFi Module with Antenna (RTL-8192CU)
$14.95  
14 pc(s)
This wifi module is a miniature USB wireless adapter with massive antenna that supports greater range and speed. It is fully complies with wireless 802.11b/g/n standards with data rate up to 300 Mbps when connecting with wireless 802.11n device. This Wifi module works well with the...
− +
Hand Crank Generator
$14.95  
Out-of-stock
This hand-held crank generator produces up to 15 volts of DC electricity. The integrated PCB includes a full bridge rectifier to provide the same output polarity for either direction the hand crank is turning. In addition, other devices can be easily connected to the screw terminal.
Out-of-stock
SGBotic Paper Circuits Kit w/Sound Card
$14.95  
Out-of-stock
SGBotic Paper Circuits kit let you learn the basics and fundamentals of an electric circuit in a fun way! Using circuit template cards, LEDs, sound card, speaker, copper tape and coin cell batteries, you will create four circuits: simple, series, parallel and sound circuits. No prior electronics...
Out-of-stock
Sharp Digital Distance Sensor - 5cm
$14.95  
8 pc(s)
The  GP2Y0D805  and  GP2Y0D810  are Sharp’s smallest and fastest distance sensors. With a sample rate of almost 400 Hz and a sensing distance to 5 cm or 10 cm, respectively, these sensors provides attractive alternatives to shorter-range ...
− +
434Mhz Wireless Transceiver Module
$14.95  
2 pc(s)
This 434Mhz Wireless Transceiver Module is a new-generation multi-channel RF transceiver operating at the sub-GHz ISM bands from 433.4-473.0MHz,. The module supports up to 100 channels, with selectable RF power transmitter and highly sensitive RF receiver. Its output power level ranges from...
− +
32x8 SPI Dot Matrix Display Module - MAX7219 - Red
$14.99  
1 pc(s)
This 32 x 8 SPI Dot Matrix Module allows you to experiment with dot matrix LED's without all the complicated wiring. The module makes use of the MAX7219 LED driver which handles all the complicated stuff such as multiplexing the LEDs and driving them at the correct currents. What's more, the...
− +
Biomedical Sensor Pad (Pack of 10)
$15.00  
Out-of-stock
Note : This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. This is a 10-pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are...
Out-of-stock
-50%
Transceiver nRF24L01+ Module with Chip Antenna
$15.00 $30.00  
1 pc(s)
This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature - very nice!...
− +
MakerBeam M3 Wing Type Bolts - 6mm
$15.00  
1 pc(s)
The wing type MakerBeam bolts make it easy to add a bracket midway between brackets already fastened. The rectangular screw head of the wing type bolt gives the possibility to add screws midway. You can insert the screw midway of a beam and turn it to ensure tightening. This way it is easy to...
− +
-9%
LiPo Charger Plus - USB Type-C
$15.00 $16.50  
1 pc(s)
The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and provided charge rate selection as well as optional thermal protection. Charge,...
− +
QTR-8A Reflectance Sensor Array
$15.00  
1 pc(s)
The QTR-8A reflectance sensor array is intended as a line sensor, but it can be used as a general-purpose proximity or reflectance sensor. The module is a convenient carrier for eight IR emitter and receiver (phototransistor) pairs evenly spaced at intervals of 0.375" (9.525 mm). Each...
− +
micro:bit EduFun Mini Project Kit - Temperature and Humidity Sensor (I2C)
$15.00  
13 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...
− +
MakerBeam Square Headed Bolts w/ Hex Hole - M3x12
$15.00  
8 pc(s)
1 bag of approximately 100 M3 bolts, 12mm - especially made for MakerBeam. The 12 mm bolts have a square head for extra tight fixing, and a hex hole in the head. Length: 12mm.
− +
Force Sensitive Resistor - Square (FSR406) - Male Pin Header
$15.50  
4 pc(s)
This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be...
− +
-11%
Non-Invasive Current Sensor - 30A
$15.50 $17.50  
1 pc(s)
This non-invasive current sensor (also known as a “split core current transformer”) can be clamped around the supply line of an electrical load to tell you how much current is passing through it. It does this by acting as an inductor and responding to the magnetic field around a...
− +
2.4GHz Duck Antenna RP-SMA - Large
$15.50  
3 pc(s)
Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized SMA Connector. Documents: Datasheet Dimensions: 0.5x7.7"
− +
MakerBeamXL - 1000mm Black Anodised (Threaded)
$15.50  
22 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
-50%
SparkFun gator:bit
$15.50 $31.00  
4 pc(s)
The SparkFun gator:bit is an all-in-one "carrier" board for your micro:bit that provides you with a fully functional development and prototyping platform. Almost every pin on the micro:bit is broken out to pads that alligator (or crocodile, if you prefer) clips so you can get the most out of...
− +
MakerBeamXL - 1000mm Clear Anodised (Threaded)
$15.50  
27 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
Mecanum Wheels For TT Gear Motor - 80mm Diameter (PAIR)
$15.50  
1 pc(s)
Mecanum wheels allow your robot to not only travel forward and backward, but also sideways! Nine rollers set on a 45° rotational axis parallel to the main rotational axis of the wheel enable a broad a range of movement. Rotating all four wheels in the same direction causes forward or backward...
− +
Right Angle Bracket For MakerBeamXL (12 pcs)
$15.50  
7 pc(s)
The stainless steel right angle bracket is a great addition to MakerBeamXL product range. The right angle brackets give you the possibilty to place one beam on top of the other. Includes 12x Stainless steel right angle bracket for MakerBeamXL
− +
10A Relay Module For 3.3V And 5V Controller
$15.50  
2 pc(s)
This 10A Relay Module is a little different to the other relays in our store - not only is it compatible with 5V Arduino boards, but also with Raspberry Pi, BBB (BeagleBoard Black), mbed, Intel Joule, Arduino 101 and other 3.3V devices. It is specially designed for low-voltage devices and...
− +
T-Bracket For MakerBeamXL (12 pcs)
$15.50  
10 pc(s)
The stainless steel T-bracket is a great addition to MakerBeamXL product range. It is compatible with both threaded and non-threaded MakerBeam. Includes 12x Stainless steel T-Bracket for MakerBeamXL
− +
-7%
RS232 Shifter SMD Without DB9
$15.75 $17.00  
5 pc(s)
The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at...
− +
LiPo Charger Basic - Micro-USB
$15.95  
Out-of-stock
If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer...
Out-of-stock
I2C 16x2 Character LCD (White on Blue) - 3.3V
$15.95  
1 pc(s)
This is another great 16x2 character LCD display with I2C interface designed for 3.3V supply. As the pin resources of the Arduino or Raspberry Pi is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with...
− +
I2C 16x2 Character LCD (Black on Grey) - 3.3V
$15.95  
6 pc(s)
This is another great 16x2 character LCD display with I2C interface designed for 3.3V supply. As the pin resources of the Arduino or Raspberry Pi is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with...
− +
I2C 20x4 Character LCD Module - 3.3V
$15.95  
3 pc(s)
This is another great 20x4 character LCD display with I2C interface that runs at 3.3V. As the pin resources of Arduino or Raspberry Pi controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with...
− +
ESP32 Development Board Lite
$15.95  
4 pc(s)
The ESP32 Development Board Lite is a compact version of standard ESP32 development board. Like other ESP32 boards, it has a 32-bit dual core microcontroller that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...
− +
I2C 16x2 Character LCD Module - 5V
$15.95  
10 pc(s)
This is another great 16x2 character LCD display with I2C interface. As the pin resources of Arduino controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you...
− +
Micro HDMI to HDMI Cable - 3 meter
$15.99  
12 pc(s)
Connect an HDMI device with a micro HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 3 meter long. Dimensions: 3 meter Long
− +
micro:bit EduFun Mini Project Kit - DS18B20 Waterproof Temperature Sensor
$16.00  
2 pc(s)
SGBotic has created a series of micro:bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakCode blocks package to remove the complexity of using these devices, making it easier for inventors to...
− +
M5Stack Module - Mini GPS
$16.50  
1 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Mini GPS Module is built around the AT6558 GNSS module. The 56-channel 6 positioning engine boasts a Time-To-First-Fix (TTFF) of...
− +
Polymer Lithium Ion Battery - 1000mAh 3.7V With JST PH Connector
$16.70  
9 pc(s)
**This battery is not available to ship outside Singapore** This is a very small, extremely lightweight battery based on Lithium Ion chemistry, with the highest energy density currently in production. Each cell outputs a nominal 3.7V at 400mAh! Comes terminated with a standard 2-pin...
− +
-50%
ubit:connect Interfacing Board for BBC micro:bit - Assembled
$16.75 $33.50  
116 pc(s)
This ubit:connect Interfacing Board is specially designed for BBC micro:bit developer. It offers an easy way to connect sensors, actuators and other circuits to the micro:bit. The board comes with an 0.91" OLED display. Together with SGBotic's customised makecode package, this OLED display...
− +
1 - 9
3 4 5 6 7 8 9 10 11 12 13

Recently Viewed