Delivery fee

New items

1 2 3 4 5 6 7 8 9
Oldest Items First
96 Per Page
433MHz Spring Coil Antenna
$0.75  
9 pc(s)
This spring coil antenna is designed for the 433MHz devices. Each antenna is constructed of phosphor copper. Features: Frequency Range(MHz)：433MHz +/-5MHz Gain(dBi)：2.15 V.S.W.R：≤1.5@433M Input Impedance( OHM)：50 Spring outer diameter: Wire diameter is 0.6mm,...
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Red)
$0.60 $0.75  
5 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including...
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Green)
$0.60 $0.75  
38 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1.5A@250VAC. Overall length (including...
− +
-33%
Panel Mount Pushbutton - Latching (10mm, Red)
$0.50 $0.75  
28 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
Panel Mount Pushbutton - Latching (10mm, Green)
$0.50  
35 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
2 x 75A 60V Brushless DC Motor Controller (HBL2360A)
Contact us for details

 
 
Roboteq 's HBL2360A is a high-current, dual channel controller for hall-sensor equipped Brushless DC motors. The controller uses the position information from the sensors to sequence power on the motors' 3 windings in order to generate smooth continuous rotation. The controller also uses...
-29%
7mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 7mm Documents : Datasheet
− +
2 Way Spring Clamp Terminal Block (Pack of 3)
$0.95  
16 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
-30%
3 Way Spring Clamp Terminal Block (Pack of 3)
$0.95 $1.35  
126 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
-10%
Big Easy Stepper Motor Driver
$31.50 $35.00  
1 pc(s)
The Big Easy Driver, designed by Brian Schmalz , is a stepper motor driver board for bi-polar stepper motors up to 2A/phase. It is based on the Allegro A4983 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685
$33.85  
1 pc(s)
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you...
− +
HDMI to VGA Video Adapter w/Audio and USB Power Out (Metal Case)
$9.95  
1 pc(s)
This nifty adapter cable with durable metal casing converts the digital HDMI video signals which are outputted from Raspberry Pi, into an analog signal required by the widely used VGA monitor. This adapter has an audio jack that provides stereo headphone/line out (HDMI 1.3 cables carry both...
− +
-8%
LilyPad Arduino 328 Main Board
$22.95 $24.95  
1 pc(s)
The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package designed to minimize snagging and profile,...
− +
MakerBeam NEMA 17 Bracket For Stepper Motor
$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.
− +
-20%
LilyPad LED White (5pcs)
$4.75 $5.95  
Out-of-stock
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
Out-of-stock
-20%
3.5" Resistive Touchscreen LCD + Pre-configured 16GB microSD Card For RaspberryPi
$37.60 $47.00  
7 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 3.5 inches 480x320 high resolution LCD display with resistive touchscreen, engineered specifically to let you quickly attached the...
− +
-20%
Resistor Kit - 1/4W 1% (600 total)
$6.40 $8.00  
9 pc(s)
Don't you hate it when you're in the middle of a build and you don't have a certain value of resistor? Don't let it happen again with this resistor kit. This kit contains a resistor color code chart and 20 each of 30 standard value 1/4 Watts resistors with 1% tolerance. It's perfect for starting...
− +
USB mini-B Cable - 30cm
$2.50  
4 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 30cm
− +
USB mini-B Cable - 50cm
$3.00  
3 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 50cm
− +
USB microB Cable - 25cm
$2.50  
1 pc(s)
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
− +
USB microB Cable - 50cm
$3.00  
Out-of-stock
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
Out-of-stock
USB Cable A to B - 50cm
$3.00  
Out-of-stock
This is the classic. It's an A to B Male/Male type peripheral cable for printers and other large peripheral devices. Compatible with Arduino Uno and Arduino Mega. Dimensions: 50cm
Out-of-stock
-50%
Thermally Conductive Adhesive
$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...
− +
ESP8266 Wifi Module SMD
$8.90  
4 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...
− +
Flex Cable for Raspberry Pi Camera - 30cm
$3.50  
11 pc(s)
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 30cm long. Each order comes with one cable, Pi Camera...
− +
Flex Cable for Raspberry Pi Camera - 50cm
$3.95  
1 pc(s)
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 50cm long. Each order comes with one cable, Pi Camera...
− +
-20%
MP3 Trigger
$60.00 $75.00  
1 pc(s)
Make some noise with your next project! The MP3 Trigger board is built to make it MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control,...
− +
Mini Real Time Clock Module (DS3231) for Raspberry Pi
$11.95  
5 pc(s)
Unlike most computers, the Pi lacks a Real-Time Clock (RTC). This means the Pi doesn't know what time it is when powered on. While your Pi is connected to a network it will be able to set it's clock correctly using NTP ( Network Time Protocol ) server. Without a network connection your Pi...
− +
Toy DC Motor Bracket - Metal
$0.20  
9 pc(s)
This compact metal bracket enables convenient mounting of our popular Toy DC Motors . ‎Ø2mm mounting holes. Note: Toy DC motor not included.
− +
Toy DC Motor Bracket - Plastic
$1.50  
13 pc(s)
This compact plastic bracket enables convenient mounting of our popular Toy DC Motors . Note: Toy DC motor not included. Documents : Dimension drawing
− +
9V Battery Snap - Heavy Duty
$0.80  
50 pc(s)
9V snap connector wth hard shell that is built stronger to last longer. Comes with color-coded wire leads. Great for replacements or projects. Length: ~ 15cm
− +
Type 2 NFC Silicone Adjustable Wristband (NTAG213) - Yellow
$3.50  
1 pc(s)
This is a blank NFC Type 2 silicone wristbands with adjustable fitting - often used for parties/events or identification but also found in other systems where a small proximity card is desired. This wristbands contains a NTAG213 RFID chip with 144 bytes of memory and an antenna, and is...
− +
3-Blade Nylon Boat Propeller - 40mm Diameter
$2.50  
11 pc(s)
Small fiber reinforced nylon propeller for boat, 3 blades and 40mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø40 x 18.5mm Center bore：1.9 mm
− +
3-Blade Boat Propeller - 27mm Diameter (5 pcs)
$0.50  
7 pc(s)
Small propeller for boat, 3 blades and 27mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø27 x 6.9mm Center bore：1.9 mm
− +
Micro HDMI to HDMI Cable - 3 meter
$15.99  
12 pc(s)
Connect an HDMI device with a micro HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 3 meter long. Dimensions: 3 meter Long
− +
Mini HDMI to HDMI Cable - 1.5 meter
$7.99  
3 pc(s)
Connect an HDMI device with a mini HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1.5 meter long This cable works with Raspberry Pi Zero W. Dimensions: 1.5 meter Long
− +
Ultrasonic Range Finder - HRXL-MaxSonar-WR
$195.00  
2 pc(s)
This outdoor sensor provides very short to long distance detection and ranging in a compact, robust PVC housing. The ultrasonic sensor meets the IP67 water intrusion standard and matches standard electrical ¾-inch PVC pipe fittings. High output acoustic power combined with continuously...
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +
Copper Tape - Conductive Adhesive, 5mm (20 Meters)
$4.95  
10 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
Translucent Silicone Tubing 7mm ID x 9mm OD - 1 meter
$4.50  
39 pc(s)
This soft, flexible tubing is specially sourced for our Diaphragm Liquid Pump and mini liquid pump . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. No tubing clamp is...
− +
Copper Tape - Conductive Adhesive, 50mm (20 Meters)
$29.95  
5 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
DELink 2 USB Link For Kangaroo PID Motion Controller
$35.00  
4 pc(s)
The DELink 2 USB Link is the perfect compliment to our Kangaroo x2 self-tuning PID motion controller. Coupled with the DEScribe software, you can upload / download settings or reset the Kangaroo to factory defaults. Utilizing the easy-to-use USB bus, changing the settings on your Kangaroo...
− +
-50%
3DR Buzzer for PX4 / Pixhawk
$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm
− +
-55%
3DR Safety Switch for PX4 / Pixhawk
$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - Green
$1.95  
1 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - White
$1.95  
3 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - Blue
$1.95  
2 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
Protoboard, Double-Sided Pad-per-Hole, 3x7cm
$1.50  
4 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 3 x 7cm, 1.6mm thick
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - Red
$1.95  
4 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
Magician Rover Chassis Kit v2
$29.90  
4 pc(s)
The Magician Rover Chassis v2 is our latest robot platform from Dagu. It features two gearmotors with 65mm wheels and a rear caster. The chassis plates are injection molded with a wide variety of mounting holes for sensors, controllers, power, etc. Simply bolt the two plastic platforms...
− +
-15%
CAN-BUS Shield
$38.25 $45.00  
1 pc(s)
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output...
− +
Mega Enclosure - Clear
$3.50  
1 pc(s)
The Arduino Mega 2560 R3 is a very big and powerful microcontroller,needless to say, you want to keep it protected. Why not protect it with one of these snazzy plastic enclosures? These cases protect the Arduino Mega 2560 from things like rogue wires that might short it out while still allowing...
− +
-20%
Servo - Generic Metal Gear (Micro Size)
$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...
− +
DC & Stepper Motor HAT for Raspberry Pi
$38.00  
Out-of-stock
Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, this HAT uses...
Out-of-stock
Nylon Ball Caster Wheel
$1.20  
39 pc(s)
The Nylon Ball Caster has the capbility to support maximum 10kg payload. The Caster is strong and lightweight. It has 20mm high round body, with a total weight of only 25g. Documents : Dimension drawing
− +
-50%
Solar Panel - 18V 2.5W
$18.75 $37.50  
2 pc(s)
Need a clean energy source to power you project? Check out this high quality, high output solar panel. Each panel features high efficient polycrystalline cells mounted onto a fibreglass PCB and covered with epoxy resin which protect the cells without reducing efficiency. A weatherproof plastic...
− +
Soil Moisture /Temperature Sensor - SHT10
$29.95  
1 pc(s)
Take your gardening project to the next level with a SHT-10 based soil sensor. The sensor includes a temperature/humidity sensor module from Sensiron in a sinter metal mesh encasing. The casing is weatherproof and will keep water from seeping into the body of the sensor and damaging it, but...
− +
Type 2 NFC White Tag - NTAG213
$1.70  
155 pc(s)
This blank NFC type 2 tag contains a small NTAG213 RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple inches away. You can use PN532 NFC/RFID breakout board , Adafruit NFC/RFID Shield for Arduino and almost any NFC enabled mobile device to...
− +
Analog Capacitive Soil Moisture Sensor- Corrosion Resistant
$14.90  
2 pc(s)
This product measures soil mositure levels by capacitive sensing, rather than resistive sensing like other types of moisture sensor. It is made of a corrosion resistant materal giving it a long service life. Insert it into soil and impress your friends with the real-time soil moisture data!...
− +
Breakout Board for Electret Microphone
$10.95  
2 pc(s)
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller's analog-to-digital converter. Each breakout comes fully assembled and works...
− +
MakerBeam Servo Bracket
$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. Documents: Mechanical drawing
− +
MakerBeam Hinge Bearing
$32.50  
3 pc(s)
Hinge bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. The 3mm inner diameter makes is easy to mount on a M3 bolt. Trebuchet movement is possible with the added copper saddle band clips,...
− +
600mm MakerBeam Clear Anodised (Threaded)
$9.50  
30 pc(s)
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
− +
Feather M0 Adalogger
$34.95  
2 pc(s)
Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 Adalogger - an 'all-in-one' Cortex M0 datalogger (or data-reader)...
− +
Peristaltic Liquid Pump
$28.99  
Out-of-stock
Move fluid safely from here to there with this very nice little pump. Unlike most liquid pumps, this is a peristaltic type - the pump squishes the silicone tubing that contains the liquid instead of impelling it directly . The upshot? The pump never touches the fluid which makes this an...
Out-of-stock
MakerBeam Bearing
$29.00  
8 pc(s)
Stainless steel bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. If you fit it to a MakerBeam it will extend about 1.5mm from the edge of the beam. The 3mm inner diameter makes is easy to...
− +
-5%
Type 2 NFC Card - NTAG216
$2.85 $3.00  
53 pc(s)
A white plastic PVC card that has an NTAG216 chip embedded inside. About the size of a credit card, this is a blank white NFC card that you can use with a card printer to customize. It houses an NTAG216 chip which holds up to 888 bytes of memory. Documents : Datasheet (NTAG216)...
− +
I2C 16x2 Character LCD Module - 5V
$15.95  
10 pc(s)
This is another great 16x2 character LCD display with I2C interface. As the pin resources of Arduino controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you...
− +
-15%
MOSFET Power Controller
$12.50 $14.75  
2 pc(s)
MOSFETs are awesome. They're like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also has sewable pads so you can use it in e-textile projects that need more juice....
− +
-21%
Analog 2-axis Thumb Joystick with Select Button
$1.55 $1.95  
3 pc(s)
This kit makes it easy to mount a PS2-like thumb joystick to your project. The 2-axis joystick contains two independent potentiometers (~10k ohm, one per axis, ) for reporting the joystick's position and a 'press in to select' button. Since it's analog, you'll need two analog reading pins on...
− +
Micro Servo - 9g
$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....
− +
USB mini-B Cable - 1 meter
$3.95  
7 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 1 meter
− +
-50%
USB mini-B Cable - 1.5 meters w/Ferrite Bead
$2.25 $4.50  
53 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. The Ferrite Bead helps to eleminate EMI. Dimensions: 1.5 meter
− +
3-Pin Cable for Sharp Distance Sensors / SRF01 (w/Male Pin Header)
$2.90  
13 pc(s)
This 30cm cable has 26 AWG wires and a 3-pin female JST PH-style connector that works with Sharp Infra-red distance sensors: GP2Y0A02YK , GP2Y0A21YK and GP2Y0A41SK0F . The other ends of the wires are terminated with male pin header. The wire color scheme matches the Sharp distance sensor...
− +
RGB LED Weatherproof Strip 60 LED/m - 5 meter
$45.00  
Out-of-stock
These are sealed non-addressable 5 meter long RGB LED strips that come packed with 60 5050 LEDs per meter. Each of these strips need a 9V to 12V power supply and you can control the entire strip at once with any micro-controller and three transistors. These strips are coated with silicon but...
Out-of-stock
-20%
Solder Leaded - 15-gram Tube
$2.55 $3.20  
1 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
-20%
SOIC to DIP Adapter 8-Pin
$3.95 $4.95  
1 pc(s)
The SparkFun 8-Pin SOIC to DIP Adapter is a small PCB that lets you adapt SOIC packages into a DIP footprint. These tiny boards are useful for modding and upgrading devices that use 8-pin DIP ICs, when the upgraded IC is only available in a SOIC footprint. You can also use these adapters for...
− +
MCP3008 - 8-Channel 10-Bit ADC With SPI Interface
$4.50  
5 pc(s)
The MCP3008 has a 8-Channel 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply...
− +
Mini RGB LED Controller with IR Remote
$3.90  
29 pc(s)
This mini 5-24VDC RGB LED Controller with 24 Button Infrared Remote is a unique RGB LED controller for use with all our 12VDC RGB LED strip. It can be used to control color effects for common anode style 5-24VDC RGB LED Lights strip. Maximum load is 2 amps per channel, 6 amps total. The...
− +
MakerBeam Corner Cube Kit - Black
$21.50  
2 pc(s)
The corner cubes are designed especially for makerbeams with threaded beam ends. The bag contains: 12x Aluminum corner cubes 50x Stainless steel countersunk bolts with flat head (M3 x 6) 1x Allen key Note : Not compatible with non-threaded MakerBeam.
− +
MakerBeam Hinge Kit
$29.50  
11 pc(s)
1 bag of MakerBeam hinges kit contains 8 hinges and 4 axes (ISO7380, M3, 14mm, A2) and 4 self locking nuts (DIN985).The hinges were specially designed to make a hinge or to mount a beam at any angle you would like.
− +
Mini RGB LED Controller with RF Remote
$3.50  
2 pc(s)
This mini 5-24VDC RGB LED Controller is loaded with functionality and has an RF remote range of up to 30 meters. It can be used to control color effects for common anode style 5-24VDC RGB LED Lights strip. The maximum load is 4 amps per channel, 12 amps total. Functions include 20 static...
− +
-20%
Load Cell - 2kg, Straight Bar
$7.90 $9.90  
20 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 2kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-25%
Raspberry Pi GPIO Tall Header - 2x20
$2.90 $3.85  
22 pc(s)
This 2x20 "tall" header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can encapsulate your Pi. This through-hole header has 40 0.1"-spaced pins and can...
− +
GPIO Reference Card For Raspberry Pi Model B+/PI 2/PI 3
$0.50  
53 pc(s)
This board makes connecting wires to the Raspberry Pi GPIO incredibly easy. It's a reference board that makes it really easy to see if you're connecting your wires correctly. We've designed the board such that it fits into our Pi enclosure . The board is only 0.8mm thick. Simply slide...
− +
Active Buzzer -12mm Continuous Tone
$0.50  
16 pc(s)
This is a small 12mm round active buzzer. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer will switched on by a 3-5V DC voltage. No other...
− +
I2C 16x2 Character LCD (White on Blue) - 3.3V
$15.95  
1 pc(s)
This is another great 16x2 character LCD display with I2C interface designed for 3.3V supply. As the pin resources of the Arduino or Raspberry Pi is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with...
− +
MakerBeamXL - 1000mm Black Anodised (Threaded)
$15.50  
22 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
MakerBeamXL - 500mm Black Anodised (Threaded)
$9.90  
13 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
Right Angle Bracket For MakerBeamXL (12 pcs)
$15.50  
7 pc(s)
The stainless steel right angle bracket is a great addition to MakerBeamXL product range. The right angle brackets give you the possibilty to place one beam on top of the other. Includes 12x Stainless steel right angle bracket for MakerBeamXL
− +
T-Bracket For MakerBeamXL (12 pcs)
$15.50  
10 pc(s)
The stainless steel T-bracket is a great addition to MakerBeamXL product range. It is compatible with both threaded and non-threaded MakerBeam. Includes 12x Stainless steel T-Bracket for MakerBeamXL
− +
T-Slot Nuts For MakerBeamXL (50pcs)
$17.50  
8 pc(s)
The MakerBeamXL T-slot nut is made of stainless steel and was specially designed to slide into the T-slot grooves of the MakerBeamXL profile. The T-slot nut is great to fasten brackets or corner cubes.
− +
Corner Cube Kit For MakerBeamXL - Black
$25.70  
3 pc(s)
This Corner Cubes can join up to three MakerBeamXL in right angle. Corner Cubes are joined with a beam by the threaded beam ends. Each set contains 12 15mmx15mmx15mm cubes Note : Not compatible with 10mmx10mm MakerBeam.
− +
Brass Sponge Solder Tip Cleaner
$7.95  
2 pc(s)
This is a brass sponge that will help clean your soldering iron tip. Use it to remove residue from your iron tip before soldering. It cleans better than conventional sponges and will not damage your iron tip. Made of low abrasive brass shavings, requires no water and won't cool down the tip.
− +
MAX6675 Temperature Sensor Kit with K-Type Thermocouple
$9.99  
3 pc(s)
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. This MAX6675 breakout board does everything for you, and can be easily interfaced with Arduino, micro:bit, Raspberry Pi and any other microcontroller via 12-bit resolution SPI bus. A...
− +
1 2 3 4 5 6 7 8 9