Delivery fee

New items

1 2 3 4 5 6 7 8 9
Sort Alphabetically: A to Z
96 Per Page
Heating Pad - 5x10cm
$7.90  
12 pc(s)
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro...
− +
Heating Pad - 5x15cm
$8.20  
1 pc(s)
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro...
− +
HerkuleX Interface Cable - 75mm
$1.60  
2 pc(s)
Interface cable for Hovis humanoid robot and HerkuleX Smart Servo. Length: 75mm
− +
HerkuleX Smart Servo DRS-0101 - 12kgf.cm
$55.00  
1 pc(s)
Download the Arduino library here ! This Dongbu's HerkuleX DRS-0101 servo is state of the art modular smart servos that support multi-drop TTL Full Duplex UART serial communications protocol with a maxium speed of 0.667Mbps. A single command can set the speed, position, LED lighting...
− +
High Torque Metal Gear Servo (270° Rotation)
$19.90  
3 pc(s)
This high-torque servo now comes with metal-gear for extra-high torque (10.5 kg/cm!) and reliability! It can rotate at approximately 270 degrees with a classic 500µS to 2500µS pulse. You can use any servo code, hardware or library to control these servos. Good for applications that require...
− +
Hook-up Stranded Wire - Red (22 AWG)
$5.30  
2 pc(s)
Standard 22 AWG stranded red wire. Use this for soldering wire or any project in which you need flexible wire. Comes in small spools of 25'.
− +
Hook-up Stranded Wire - White (22 AWG)
$5.30  
2 pc(s)
Standard 22 AWG stranded White wire. Use this for soldering wire or any project in which you need flexible wire. Stranded wire is recommended for projects where the wire has a bend or stress point. Comes in small spools of 25'
− +
Hook-up Wire - Red (22 AWG)
$4.95  
5 pc(s)
Standard 22 AWG solid Red hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes in small spools of 25'.
− +
Hook-up Wire - White (22 AWG)
$4.95  
3 pc(s)
Standard 22 AWG solid White hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes in small spools of 25'.
− +
Humidity and Temperature Sensor - DHT11
$4.95  
1 pc(s)
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires...
− +
Humidity Sensor - HIH-4030 Breakout
$26.60  
3 pc(s)
This is a breakout board for Honeywell's HIH-4030 humidity sensor. The HIH-4030 measures relative humidity (%RH) and delivers it as an analog output voltage. You can connect the output of the sensor directly to an ADC on a microcontroller; and, thanks to the sensor's near linear voltage...
− +
I2C 16x2 Character LCD (Black on Grey) - 3.3V
$15.95  
6 pc(s)
This is another great 16x2 character LCD display with I2C interface designed for 3.3V supply. As the pin resources of the Arduino or Raspberry Pi is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with...
− +
I2C 16x2 Character LCD (White on Blue) - 3.3V
$15.95  
1 pc(s)
This is another great 16x2 character LCD display with I2C interface designed for 3.3V supply. As the pin resources of the Arduino or Raspberry Pi is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with...
− +
I2C 16x2 Character LCD Module - 5V
$15.95  
10 pc(s)
This is another great 16x2 character LCD display with I2C interface. As the pin resources of Arduino controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you...
− +
I2C 16x2 Character LCD w/RGB Backlight
$18.95  
1 pc(s)
This is another great 16x2 character LCD display with I2C interface designed for 3.3V and 5V supply. The LCD features full colour RGB background, allowing you to change the background colour to meet your project requirement. The LCD uses I2C communication interface - only four wires...
− +
I2C 16x2 Character LCD w/RGB Text
$18.95  
4 pc(s)
This is another great 16x2 character LCD display with I2C interface designed for 3.3V and 5V supply. The LCD features full colour RGB text, allowing you to change the text colour to meet your project requirement. The LCD uses I2C communication interface - only four wires (power,...
− +
I2C 20x4 Character LCD Module - 3.3V
$15.95  
3 pc(s)
This is another great 20x4 character LCD display with I2C interface that runs at 3.3V. As the pin resources of Arduino or Raspberry Pi controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with...
− +
I2C 20x4 Character LCD Module - Black on Green 5V
$17.95  
8 pc(s)
This is another great 20x4 character LCD display with I2C interface. As the pin resources of Arduino controller is limited, your project may be not able to use standard LCD module after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you...
− +
I2C Adapter
$3.95  
3 pc(s)
This I2C Adapter provides a convenient way to connect the OLED display module and other I2C devices to Jetson Nano or Raspberry Pi. The 3.3V, Ground, SCL and SDA pins are breakout to multiple connectors. A XH2.54 cable is included in the package. NOTE : You can still access the 5V pin on...
− +
-31%
Illuminated Capacitive Switch Module - Blue
$2.50 $3.60  
2 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-31%
Illuminated Capacitive Switch Module - Green
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-31%
Illuminated Capacitive Switch Module - Red
$2.50 $3.60  
1 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-31%
Illuminated Capacitive Switch Module - Yellow
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-20%
IMX219 Camera Module For Pi Cam V2 - 8 MegaPixels, 160° View Angle
$27.60 $34.50  
7 pc(s)
This IMX219 camera module is supplementary for Raspberry Pi official camera to fulfil the demands for wide view angle. It features 8-megapixel 160 degree view angle. If you got a Raspberry Pi Camera Board V2 and require wide view angle, here it is. Note : Follow the instruction in this...
− +
-40%
In-Line Power Switch - White
$0.60 $1.00  
3 pc(s)
This inline switch is great when you just want a simple on/off toggle switch that's already enclosed. Inside is a double pole rocker switch with screw terminals. Features : SPDT 6A, 250VAC Clicky Sound Dimensions : 60.9(L) x 26.5(W) x 15.5(H)mm
− +
-31%
In-line power switch for 2.1mm barrel jack
$2.50 $3.60  
10 pc(s)
Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an...
− +
Infra-red LED 950nm - 5mm (10 pcs)
$1.20  
89 pc(s)
This is a very simple, clear infrared LED. These devices operate between 940-950nm and work well for generic IR systems including remote control and touch-less object sensing. Pair them with any of our IR receivers (see Related Items below). 1.5VDC forward voltage and 50mA max forward...
− +
Infra-red Phototransistor 940nm
$0.99  
28 pc(s)
This is a very simple, clear infrared phototransistor. These devices operate between 940-950nm and work well with our infrared LED . Phototransistors are similar to photoresistors (or LDR) but produce both current and voltage, while photoresistors only produce current....
− +
Infrared Obstacle Avoidance Sensor
$1.95  
10 pc(s)
The Infrared Obstacle Avoidance Sensor has a pair of infrared transmitting and receiving sensors. The infrared LED emits Infrared signals at certain frequency and when an obstacle appears on the line of infrared light, it is reflected back by the obstacle which is sensed by the receiver....
− +
Infrared Receiver Diode (TSOP38238)
$3.00  
33 pc(s)
Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes. The TSOP38238 is a miniaturized receiver for infrared remote control...
− +
Infrared Remote Control (21 Buttons)
$1.50  
10 pc(s)
Have you ever needed a cheap way to activate something from across the room? Infrared remotes are still the cheapest way to wirelessly control a device. This 21 buttons remote controller works with TSOP38238 infrared receiver which have an operating voltage from 2.5V - 5.5V. Includes :...
− +
Infrared Remote Control Kit
$1.90  
6 pc(s)
Have you ever needed a cheap way to activate something from across the room? Infrared remotes are still the cheapest way to wirelessly control a device. The IR remote in this kit offers buttons for four directions, select and basic number keys. It is ideal for implementing an IR remote control...
− +
-50%
Interface Cable RP-SMA to U.FL
$3.45 $6.95  
4 pc(s)
This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the DPAC 802.11 modules. Dimensions: 4" Length
− +
-50%
IOIO and Breadboard Holder
$2.60 $5.20  
1 pc(s)
This holder allows you to safely secure a IOIO development board and a self-adhesive breadboard in place to easily run jumper wires in between the two to form simple or complex prototyping circuits. Unlike it’s cousin, for the Arduino, this IOIO and breadboard holder has been made specifically...
− +
-7%
ISL29125 RGB Light Sensor
$12.50 $13.50  
2 pc(s)
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity...
− +
J1962 ODBII To Open End - Male 1.5M
$5.50  
7 pc(s)
OBDII is an on board diagnostics standard that is used on a large variety of cars. OBD-II provides access to numerous data from the engine control unit (ECU) and offers a valuable source of information when troubleshooting problems inside a vehicle. If you're not sure if your car works with...
− +
-33%
Jumper Cap - 2 Pin (Pack of 5)
$0.30 $0.45  
249 pc(s)
These are two pin jumper caps (also called shunts) that will create an electrical connection between two pin headers. Commonly used to modify settings on a board or device.
− +
-37%
Jumper Wire Kit
$2.50 $3.95  
1 pc(s)
This is a time saving kit of jumper wires - cut, stripped, and pre-bent for your prototyping pleasure. Included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each.
− +
-20%
Jumper Wires Premium 12" F/F Pack (Approx. 100pcs)
$25.60 $32.00  
13 pc(s)
These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Approx. 100 pcs per pack
− +
Jumper Wires Premium 12" F/F Pack of 10
$3.50  
6 pc(s)
These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one package of ten jumpers (colors shown). We use these wires for everything! They work great...
− +
Jumper Wires Premium 12" M/F Pack of 10
$3.50  
17 pc(s)
These are 12" long jumper wires terminated as male to female. Use these to jumper from any male or female header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of ten jumpers (colors shown). We use these wires for everything! They work...
− +
Jumper Wires Premium 12" M/M Pack of 10
$3.50  
2 pc(s)
These are 12" long jumper wires terminated as male to male. Use these to jumper from any female header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of ten jumpers (colors shown). We use these wires for everything! They work great with...
− +
-20%
Jumper Wires Premium 6" F/F Pack (Approx. 100pcs)
$22.40 $28.00  
13 pc(s)
These are 6" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Approx. 100 pcs per pack
− +
Jumper Wires Premium 6" M/M Pack of 10
$2.95  
1 pc(s)
These are 155mm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Combine these with our female to female jumpers to create a male to female jumper. Multiple jumpers can be installed next to one another on a 0.1"...
− +
-20%
Keypad - 16 Button (Alphanumeric)
$4.95 $6.20  
2 pc(s)
This is a basic 16 button keypad that has been designed for easy user input and functionality. The buttons are set up in a matrix format which allows a microcontroller to 'scan' the 8 output pins to see which of the 16 buttons is being pressed. Each of the keypad's 16 buttons has been...
− +
Kitronik Edge Connector Breakout Board for BBC micro:bit
$8.90  
9 pc(s)
Looking to do more with your BBC micro:bit? Unlock its potential with this pre-built version of our Edge Connector Breakout Board! This breakout board has been designed to offer an easy way to connect additional circuits and hardware to the pins on the edge of the BBC micro:bit. It provides...
− +
KittenBot IO:bit for micro:bit - Version 2.0
$12.00  
11 pc(s)
This KittenBot's IO:bit is a feature packed expansion board for the micro:bit. It breaks out all the IO pins (inputs, outputs) and adds extra hardware to make your next micro:bit project shine. The small form factor and two LEGO-compatible pin holes make it easy to fit into the project you might...
− +
L298 Dual Motor Driver Module 2A
$5.50  
3 pc(s)
This dual motor driver is based on the L298N heavy-duty dual H-bridge controller, which can be used to drive two DC motors at up to 2A each, with a voltage between 5 and 35V DC - or one stepper motor or 2 solenoids with ease. The driver has a nice heatsink to keep the L298N cool and all...
− +
Large Breadboard Self-Adhesive, 830 Tie-In Points
$3.50  
7 pc(s)
This is a medium sized breadboard with 830 tie-points, self-adhesive backing and two power rails on both sides. Dimensions: 165(L) x 54 (W) x 9(H) mm
− +
Large Fan Blade - 170mm Diameter
$4.50  
6 pc(s)
Large fan blade for wind energy project. 170mm in diameter and has 1.9mm center bore for 2mm motor shaft. NOTE: Toy DC motor not included. Dimensions : Ø170 x 10mm Center bore：1.9 mm
− +
LCD Keypad Shield for Arduino
$9.90  
1 pc(s)
The LCD Keypad Shield for Arduino includes a 2x16 LCD display and 6 momentary push buttons. Pins 4, 5, 6, 7, 8, 9 and 10 are used to interface with the LCD. Analog Pin 0 is used to read the push buttons. The shield operates at 5V. Features: Contrast adjustment (turns...
− +
LED - RGB Clear Common Anode - 5mm
$0.95  
63 pc(s)
Ever hear of a thing called RGB? Red, Green, Blue? How about an RGB LED? These 5mm units have four pins: one for each color and a common anode. Use this one LED for three status indicators or pulse width modulate all three and get mixed colors! Note: The datasheet below is for the...
− +
LED - RGB Clear Common Cathode - 5mm
$0.95  
205 pc(s)
Ever hear of a thing called RGB? Red, Green, Blue? How about an RGB LED? These 5mm units have four pins - Cathode is the longest pin. One for each color and a common cathode. Use this one LED for three status indicators or pulse width modulate all three and get mixed colors!...
− +
-8%
LilyPad Arduino 328 Main Board
$22.95 $24.95  
1 pc(s)
The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package designed to minimize snagging and profile,...
− +
-27%
LilyPad Buzzer
$6.50 $8.85  
2 pc(s)
This is a small buzzer for the LilyPad system. Use 2 I/O pins on the LilyPad main board and create different noises based on the different frequency of I/O toggling. Loud enough to hear inside a pocket but not obtrusively loud. Please note: This is an inductive buzzer meaning that is will act...
− +
-20%
LilyPad LED Blue (5pcs)
$4.75 $5.95  
3 pc(s)
This is a simple pack of five Blue LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-20%
LilyPad LED Pink (5pcs)
$4.75 $5.95  
7 pc(s)
Here is a simple 5 pack of pink LEDs for LilyPad, or whatever else you can dream up. Light up the night! LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting...
− +
-20%
LilyPad LED Red (5pcs)
$4.75 $5.95  
4 pc(s)
This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-20%
LilyPad LED White (5pcs)
$4.75 $5.95  
Out-of-stock
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
Out-of-stock
-20%
LilyPad LED Yellow (5pcs)
$4.75 $5.95  
7 pc(s)
This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-50%
LilyPad Protoboard Large
$4.75 $9.50  
1 pc(s)
This is a large board for prototyping through hole components with the LilyPad system. There are an array of pins all shorted together with 10mil traces. This allows for quick and easy prototyping - all you have to do is cut the traces between holes you don't want connected! Standard 0.1"...
− +
-31%
LilyPad Reed Switch
$5.50 $7.95  
1 pc(s)
The LilyPad Reed Switch is a simple breakout for a reed switch that will make it easy to use in e-textiles circuits in exactly the same manner that you can currently use the LilyPad Button and Switch. In order to make it more durable for wearable use, we've used a different style of reed switch,...
− +
-31%
LilyPad RGB LED
$5.50 $7.95  
3 pc(s)
Blink any color you need! Use the LilyPad RGB LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can produce a broad variety of colors. Each of the colors in the RGB LED are connected to one of the sew tabs on the board labeled R, G, and B. The color...
− +
-20%
LilyPad Simple Power
$13.55 $16.95  
Out-of-stock
The LilyPad Simple Power is a simple e-textile board that lets you connect and charge a lipo battery and switch it on or off, that’s it! We provide you with a JST connector and a slide switch, you supply the battery and sewing skills! With this LilyPad Simple Power, you should find no...
Out-of-stock
-50%
LilyPad SimpleSnap Protoboard
$6.00 $12.00  
3 pc(s)
The LilyPad SimpleSnap Protoboard is a new, easy way to create e-textiles projects with LilyPad that are modular and can be disassembled or broken down, it's also a great way to prototype! The SimpleSnap Protoboard is made to connect to the SimpleSnap main board so that the board is...
− +
-25%
LilyPad Slide Switch
$2.95 $3.95  
2 pc(s)
This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to...
− +
Line Follower Array
$9.95  
31 pc(s)
This SGBotic Line Follower Array gives your robot the ability to follow a dark line on a white background or vice-versa. It has four IR sensors that have been configured to output digital signal. The array features visible LEDs which turn on when the sensors detect reflected IR light. You...
− +
Line Follower Sensor
$1.99  
6 pc(s)
The Line Follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. It can detect transitions from light to dark (lines) or even objects directly in front of it. The sensor has an...
− +
Line Follower Sensor (Adjustable)
$1.99  
Out-of-stock
The Line Follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. It can detect transitions from light to dark (lines) or even objects directly in front of it. The sensor has an...
Out-of-stock
LiPo Charger Basic - Micro-USB
$15.95  
Out-of-stock
If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer...
Out-of-stock
-9%
LiPo Charger Plus - USB Type-C
$15.00 $16.50  
1 pc(s)
The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and provided charge rate selection as well as optional thermal protection. Charge,...
− +
-25%
LiPower Shield
$36.00 $48.00  
2 pc(s)
Is there anything an Arduino can't do? Well, for one, most of them can't be powered directly from a 3.7V LiPo battery; much less charge and monitor that battery. The SparkFun LiPower Shield takes care of this by combining the functionality of two of our favorite battery power boards: the...
− +
-20%
Load Cell - 10kg, Straight Bar
$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 1kg, Straight Bar
$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Cell - 20kg, Straight Bar
$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 2kg, Straight Bar
$7.90 $9.90  
20 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 2kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Cell - 5kg, Straight Bar
$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock
Load Cell Amplifier - HX711
$14.20  
3 pc(s)
This Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the amplifier to your microcontroller you will be able to read the changes in the resistance of the load cell and with some calibration you'll be able...
− +
-20%
Load Sensor - 50kg
$7.90 $9.90  
12 pc(s)
This load cell / sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. Each straight bar load cell is made from an aluminum-alloy and is capable of measure up to about 50kg. Documents : Specifications Load Sensor Tutorial (NerdKits)
− +
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Low Current DC Toy Motor w/ Male Lead Wire
$2.20  
10 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...
− +
Low Profile Aluminum Case For Raspberry Pi 4
$19.99  
7 pc(s)
Raspberry Pi is everybody's favorite little computer; the last thing you want is something bad happens to it. Why not protect it with an aluminum case? This elegantly crafted Raspberry Pi 4 case is designed for the perfect combination of durability, affordability, and strength. The case...
− +
Low Speed Gearmotor - 3V 20rpm
$4.99  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...
− +
Low Speed Gearmotor - 5V 10rpm
$4.99  
4 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...
− +
Low Speed Gearmotor - 5V 5rpm
$4.99  
3 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
− +
-21%
LPG Gas Sensor - MQ-6
$5.95 $7.50  
1 pc(s)
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing  LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has a high sensitivity and fast response...
− +
LV-MaxSonar-EZ0 - High-Performance Ultrasonic Range Finder
$48.00  
5 pc(s)
The LV-MaxSonar-EZ0 from Maxbotix offers very short to long-range detection and ranging, in an incredibly small package with ultra low power consumption. The LV-MaxSonar-EZ0 detects objects from 0-inches to 254-inches (645 cm) and provides sonar range information from 6-inches(15.24cm)...
− +
LV-MaxSonar-EZ4 - High-Performance Ultrasonic Range Finder
$48.00  
1 pc(s)
The LV-MaxSonar-EZ4 from Maxbotix offers very short to long-range detection and ranging, in an incredibly small package with ultra low power consumption. The LV-MaxSonar-EZ4 detects objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from...
− +
M12 (S-Mount) lens - 12mm
$6.45  
3 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 12mm fixed lens with IR Cut Filter...
− +
M12 (S-Mount) lens - 16mm (5 MegaPixels)
$9.95  
3 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 16mm fixed lens with IR Cut Filter...
− +
M12 (S-Mount) lens - 3.6mm
$4.45  
11 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 3.6mm fixed lens with IR Cut Filter...
− +
M12 (S-Mount) lens - 6mm
$4.45  
10 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 6mm fixed lens with IR Cut Filter provides...
− +
M12 (S-Mount) lens - 8mm
$6.45  
12 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 8mm fixed lens with IR Cut Filter provides...
− +
M12 (S-Mount) Plastic Lock Ring
$0.10  
117 pc(s)
M12x0.5mm Plastic Lock Ring for securing M12 Lenses on lens holders.
− +
M3 Hex Brass Standoff Mounting Kit #1
$0.95  
2 pc(s)
This Mounting Kit is used to secure HC-SR05 Ultrasonic Sensor Adaptor and Line Follower Array to our 2WD Robot Chassis Kit . Kit includes: M3 Standoff (2 pcs each) 10mm 20mm M3 Screw (4 pcs) M3 Nuts (4 pcs)
− +
M3 Nuts
$11.90  
1 pc(s)
1 bag of approximately 250 pcs M3 nuts. Compatible with all MakerBeam bolts
− +
1 2 3 4 5 6 7 8 9