Delivery fee

New items

1 2 3 4 5 6 7 8
2 - 9
Sort by Price: High to Low
96 Per Page
RPLIDAR A2M8 360° Laser Scanner - 12 Meters
$499.95  
1 pc(s)
IMPORTANT: This version (A2M8R4), with maximum laser power of 5mW, is a class 3a laser apparatus and does not require license to possess or use. The laser power of newer version (A3) has increased to 10-12mW which make it a controlled class 3b apparatus. Licenses are required to legally...
− +
Ultrasonic Range Finder - HRXL-MaxSonar-WR
$195.00  
2 pc(s)
This outdoor sensor provides very short to long distance detection and ranging in a compact, robust PVC housing. The ultrasonic sensor meets the IP67 water intrusion standard and matches standard electrical ¾-inch PVC pipe fittings. High output acoustic power combined with continuously...
− +
Zumo Robot for Arduino v1.2 (Assembled with 75:1 HP Motors)
$189.95  
Out-of-stock
The Zumo robot is a low-profile tracked robot platform intended for use with an Arduino (or compatible device) as its main controller. It measures less than 10 cm on each side and weighs approximately 300 g with an Arduino Uno and batteries (165 g without, as shipped), so it is both small...
Out-of-stock
-20%
Sabertooth 2x25A 6V-24V Regenerative Motor Driver (v2)
$188.00 $235.00  
2 pc(s)
The Sabertooth 2X25 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered robots - up to 100lbs in combat or 300lbs for general purpose robotics. Out of the box, the Sabertooth can supply two DC brushed motors with up...
− +
1047_2B - PhidgetEncoder HighSpeed 4-Input
$178.00  
Out-of-stock
The PhidgetEncoder Highspeed 4-Input interfaces with any 5V quadrature encoder. A quadrature encoder is the most commonly used feedback device for a DC or stepper motor. With an encoder, you can keep track of how far your motor has turned, which then allows you to control the position and...
Out-of-stock
MakerBeam Starter Kit - Black Anodised Threaded
$169.00  
Out-of-stock
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
Out-of-stock
YDLIDAR X4 360° Laser Scanner - 10 Meters
$155.00  
Out-of-stock
IMPORTANT: This version (X4), with maximum laser power of 5mW, is a class 3a laser apparatus and does not require license to possess or use. The YDLIDAR X4 360° Laser Scanner is the low cost 360 degree two-dimensional LiDAR. This product can perform 360 degree scan within 10-meter...
Out-of-stock
Pololu Dual VNH5019 Motor Driver Shield for Arduino
$126.00  
3 pc(s)
This motor driver shield and its corresponding Arduino library make it easy to control two bidirectional, high-power, brushed DC motors with an Arduino or Arduino clone. The board features a pair of robust VNH5019 motor drivers from ST, which operate from 5.5 to 24 V and can deliver a...
− +
Pololu Dual G2 High-Power Motor Driver 24v14 for Raspberry Pi
$112.00  
1 pc(s)
These G2 dual high-power motor drivers are add-on boards for the Raspberry Pi, featuring pairs of discrete MOSFET H-bridges which operate from 5 to 36 V and can deliver a continuous 14A per channel without a heat sink. The drivers offer basic current limiting functionality, and they accept...
− +
Pixy2 CMUCam5
$105.00  
Out-of-stock
The Pixy2 CMUcam5 is smaller, faster and more capable than the original Pixy. Like its predecessor, the Pixy2 can learn to detect objects that you teach it, just by pressing a button. Additionally, the Pixy2 has new algorithms that detect and track lines for use with line-following robots....
Out-of-stock
Pololu Dual MC33926 Motor Driver for Raspberry Pi
$98.00  
3 pc(s)
This motor driver board is an add-on for a compatible Raspberry Pi (Model B+ or newer), including the Pi 3 Model B+ and Model A+, that lets it easily control a pair of bidirectional, brushed DC motors. The expansion board uses a pair of Freescale MC33926 motor drivers, which operate from 5 to 28...
− +
micro:bit EduFun Mini Project Kit - Mini Thermal Printer
$95.00  
1 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...
− +
-20%
7" Capacitive Touchscreen LCD - 1024x600 + 16GB microSD Card For Pi 4
$95.00 $118.75  
5 pc(s)
This 7" high resolution LCD display is designed to provide a quick and easy interface to Raspberry Pi 2 / Pi 3 / Pi 4 and other mini PC such as BeagleBone Black, Banana Pi and PC running on Windows 7/8/10. It features a fully assembled 7" 1024x600 IPS high resolution LCD screen with...
− +
-30%
SMC04 High-Power Motor Controller w/Feedback
$88.00 $125.00  
1 pc(s)
The SMC04 high-power motor controller with feedback has multiple interface and feedback options that simplify servo control of commonly available DC motors. T he module features three independent interfaces: a serial protocol for microcontroller-based applications, a pulse-width...
− +
Ultrasonic Range Finder - XL-Maxsonar EZL0 (MB1260)
$88.00  
2 pc(s)
The XL‑MaxSonar‑EZL0 offers the widest and most sensitive beam pattern of any indoor sensor we currently offer. This makes the XL-MaxSonar-EZL0 an excellent choice wherever wide beam detection, reliable people detection, or reliable small obstacle detection are required. In addition to...
− +
Pololu 9V, 15A Step-Down Voltage Regulator D24V150F9
$85.95  
3 pc(s)
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 9V with an available output current of around 15 A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for...
− +
Pololu 5V, 15A Step-Down Voltage Regulator D24V150F5
$83.95  
1 pc(s)
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 5 V with an available output current of around 15 A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for...
− +
Ultimate GPS Breakout - 66 channel w/10 Hz updates - Version 3
$75.00  
2 pc(s)
The Ultimate GPS Breakout is built around the MTK3339 chipset, a no-nonsense, high-quality GPS module that can track up to 22 satellites on 66 channels, has an excellent high-sensitivity receiver (-165 dB tracking!), and a built in antenna. It can do up to 10 location updates a second for...
− +
Arduino Mega 2560 R3 ( A000067 )
$69.95  
1 pc(s)
Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing / Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash,...
− +
Analog pH Meter Kit V2
$69.95  
Out-of-stock
DFRobot Gravity: Analog pH meter V2 is specifically designed to measure the pH of the solution and reflect the acidity or alkalinity. It is commonly used in various applications such as aquaponics, aquaculture, and environmental water testing. As an upgraded version of pH meter V1,...
Out-of-stock
-7%
RGB LED Matrix Panel - 32x32
$69.95 $75.00  
1 pc(s)
Are you looking to add a lot of color to your project? These massive 32x32 RGB LED panels are an awesome place to start. You can create animations, games, or all sorts of other fun displays with them. Yes, you read that right: a 32x32 LED matrix, that's 1024 LEDs on a 7.5" x 7.5" board. On...
− +
Ultrasonic Range Finder - XL-Maxsonar EZ4 (MB1240)
$65.00  
4 pc(s)
The XL series of MaxSonars are a super high-performance version of the easy-to-use sonar range finder from Maxbotix . The XL series of this sensor features higher resolution, longer range, higher power output and better calibration when compared to the LV version . We are...
− +
SGBotic EDUKIT2 For Arduino
$65.00  
Out-of-stock
Interested in learning to work with Arduino but not sure where to start? This EDUKIT2 is a great way for you to get started with programming and hardware interaction with the Arduino Uno board. The kit includes the latest Arduino Uno R3 (Italy), breadboard, jumper wires, sensors, and other...
Out-of-stock
-10%
SGBotic Micro:bit Starter Kit (w/BBC micro:bit v2.2)
$62.95 $69.95  
2 pc(s)
If you are a beginner looking to learn programming and electronics, look no further than this SGBotic Micro:bit Starter Kit. This kit is designed to introduce programming and basic electronic interfacing to a user with absolutely no experience in these areas. It contains everything you need...
− +
-20%
5" Resistive Touchscreen LCD For Pi 4
$60.40 $75.50  
12 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 5 inches 800x480 high resolution LCD display with resistive touchscreen and a HDMI adapter, engineered specifically to let you...
− +
-20%
MP3 Trigger
$60.00 $75.00  
1 pc(s)
Make some noise with your next project! The MP3 Trigger board is built to make it MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control,...
− +
SGBotic EduFun Buggy for Micro:bit (rev.B)
$59.95  
Out-of-stock
SGBotic EduFun Buggy for Micro:bit is designed for learning basic robotics using BBC Micro:bit and MakeCode graphical programming. Although this kit is targeted for beginners with no prior robotic experience, experienced users will find it useful and fun too. The kit includes all parts required...
Out-of-stock
Coin Acceptor - Programmable 4 Coin Type
$59.95  
2 pc(s)
Your project may be free-as-in-speech, but that doesn't mean it has to be free-as-in-beer. This handy coin validator/acceptor module is just like the ones you've seen in arcades. This model has the cool ability to accept up to 4 different coins! For example, you can program it for 4...
− +
Ultrasonic Range Finder - I2CXL-Maxsonar EZ4 (MB1242)
$58.50  
2 pc(s)
The I2CXL-MaxSonar-EZ sensors now feature an I2C bus. This allows for easy I2C integration and multisensor operation using a single bus. The I2CXL‑MaxSonar‑EZ4 has the highest noise tolerance and narrowest beam of any of our indoor sensors. The sensor is designed and calibrated to...
− +
Parallax PING))) Ultrasonic Sensor
$58.50  
2 pc(s)
Parallax's PING)))™ ultrasonic sensor provides a very low-cost and easy method of distance measurement. This sensor is perfect for any number of applications that require you to perform measurements between moving or stationary objects. Naturally, robotics applications are very popular but...
− +
Ultrasonic Range Finder - XL-Maxsonar EZ0 (MB1200)
$58.50  
4 pc(s)
The XL series of MaxSonars are a super high-performance version of the easy-to-use sonar range finder from Maxbotix . The XL series of this sensor features higher resolution, longer range, higher power output and better calibration when compared to the LV version . We are...
− +
-20%
Arduino Sensor Kit (34 Sensor Modules)
$55.60 $69.50  
1 pc(s)
Note: For safety reasons and to comply with local government regulation, this kit does not contain any Laser Emitter and sensors containing Mercury. The sensor kit for the Arduino system consists of 34 individual sensor modules which can be used to carry out many interesting...
− +
-20%
PicoBoard
$55.20 $69.00  
1 pc(s)
The PicoBoard allows you to create interactions with various sensors. Using the Scratch programming language, you can easily create simple interactive programs based on the input from sensors. The PicoBoard incorporates a light sensor, sound sensor, a button and a slider, as well as 4...
− +
HerkuleX Smart Servo DRS-0101 - 12kgf.cm
$55.00  
1 pc(s)
Download the Arduino library here ! This Dongbu's HerkuleX DRS-0101 servo is state of the art modular smart servos that support multi-drop TTL Full Duplex UART serial communications protocol with a maxium speed of 0.667Mbps. A single command can set the speed, position, LED lighting...
− +
SparkFun OpenScale
$50.50  
4 pc(s)
The SparkFun OpenScale is a simple-to-use, open source solution for measuring weight and temperature. It has the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision. Simply...
− +
M5Stack Stackable Module - GPS (72 Channels UBlox NEO-M8N)
$50.20  
1 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack GPS Module is built around the NEO-M8N GNSS module from ublox. The NEO-M8 modules utilize concurrent reception of up to three GNSS...
− +
-71%
USB Weather Board
$50.00 $175.00  
2 pc(s)
Got weather? This board can handle it. The USB Weather Board includes onboard sensors for barometric pressure, humidity, temperature, and light level. We've also added headers in the new version so you can connect the board to the weather meters (not included), adding sensors for wind...
− +
8 MegaPixels Camera Module for Jetson Nano (160° View Angle)
$49.50  
5 pc(s)
This 8 Mega Pixels Camera Module is a custom designed add-on for Jetson Nano. The camera features a Sony IMX-219 image sensor and uses the dedicated CSI interface for connecting to the Jetson Nano. This camera module is capable of 1080p video and still images. The board itself is tiny,...
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Fisheye Lens
$48.00 $60.00  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
-20%
Electric Paint Lamp Kit
$48.00 $60.00  
6 pc(s)
Make three paper lamps with no tools, no programming, no special skills required. A great gift for anyone that needs more light in their life! Transform a piece of paper into a beautiful lamp in three easy steps. Paint, plug, and play! Use this Electric Paint to create custom...
− +
Radiolink SE100 GPS Module for PixHawk
$48.00  
2 pc(s)
This is the SE100 GPS Module designed for the pixhawk 2.4. It is built around the M8N GNSS module from ublox. The M8N modules utilize concurrent reception of up to three GNSS systems (GPS/Galileo together with BeiDou or GLONASS), recognize multiple constellations simultaneously and provide...
− +
LV-MaxSonar-EZ0 - High-Performance Ultrasonic Range Finder
$48.00  
5 pc(s)
The LV-MaxSonar-EZ0 from Maxbotix offers very short to long-range detection and ranging, in an incredibly small package with ultra low power consumption. The LV-MaxSonar-EZ0 detects objects from 0-inches to 254-inches (645 cm) and provides sonar range information from 6-inches(15.24cm)...
− +
LV-MaxSonar-EZ4 - High-Performance Ultrasonic Range Finder
$48.00  
1 pc(s)
The LV-MaxSonar-EZ4 from Maxbotix offers very short to long-range detection and ranging, in an incredibly small package with ultra low power consumption. The LV-MaxSonar-EZ4 detects objects from 0-inches to 254-inches (6.45-meters) and provides sonar range information from...
− +
-40%
Mini Thermal Printer
$45.00 $75.00  
1 pc(s)
This is a thermal printer like you would find on a cash register or adding machine. It will print simple strings passed to it via TTL serial, bitmap images (poorly) and it even generates several different formats of barcodes! The thermal printer takes 57mm wide thermal paper with a...
− +
AltIMU-10 v6 Gyro, Accelerometer, Compass, and Altimeter (LSM6DSO, LIS3MDL, and LPS22DF Carrier)
$45.00  
2 pc(s)
The Pololu AltIMU-10 v6 is a compact (1.0″ × 0.5″) board that combines ST's LSM6DSO 3-axis gyroscope and 3-axis accelerometer, LIS3MDL 3-axis magnetometer, and LPS22DF digital barometer to form an inertial measurement unit (IMU) and altimeter. These sensors are great ICs, but their...
− +
USB-ISS - Enhanced USB-I2C Module
$45.00  
Out-of-stock
The USB-ISS Multifunction USB Communications Module provides a complete interface between your PC and the I2C bus, SPI bus, a Serial port and general purpose Analogue Input or Digital I/O. The module is powered from the USB. Operating voltage is selectable between 3.3V and 5V and...
Out-of-stock
RGB LED Weatherproof Strip 60 LED/m - 5 meter
$45.00  
Out-of-stock
These are sealed non-addressable 5 meter long RGB LED strips that come packed with 60 5050 LEDs per meter. Each of these strips need a 9V to 12V power supply and you can control the entire strip at once with any micro-controller and three transistors. These strips are coated with silicon but...
Out-of-stock
Teensy 4.0 - Headers (USA)
$42.90  
4 pc(s)
Teensy 4.0 is the latest Teensy, offering the fastest microcontroller and powerful peripherals in the Teensy 1.4 by 0.7 inch form factor. It features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest microcontroller available today. Teensy 4.0 is the same size and...
− +
SWADJHV High Voltage Step Down Adjustable Switching Regulator
$42.50  
4 pc(s)
The SWADJHV is the a high-voltage edition of our popular DE-SWADJ adjustable switching reulators. It is designed to accept an input voltage ranging from 5-60V, allowing you to power a variety of applications from extremely high-voltage sources. The SWADJHV is pin-compatible with the common 78XX...
− +
Dual MAX14870 Motor Driver for Raspberry Pi
$42.00  
4 pc(s)
This motor driver expansion board and its corresponding Python library make it easy to control a pair of bidirectional, brushed DC motors with a compatible Raspberry Pi (Model B+ or newer), including the Pi 3 Model B+ and Model A+. The expansion board features two MAX14870 H-bridge motor...
− +
DE-SWADJ3 Step Down Adjustable Switching Regulator 25W
$42.00  
6 pc(s)
The DE-SWADJ 3 is a larger version of our DE-SWADJ adjustable step down voltage regulator. Previously it was necessary to put multiple DE-SWADJ units in parallel to achieve ratings over 1A, which was bulky, expensive and carried with it a considerable increase in dropout voltage. The...
− +
-11%
Arduino Uno Rev 3 ( A000066 )
$39.95 $45.00  
Out-of-stock
This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf...
Out-of-stock
Miniature Capacitive Fingerprint Sensor
$39.95  
1 pc(s)
Secure your project with biometrics - this all-in-one Capacitive Fingerprint Sensor will make adding fingerprint detection and verification super simple. Similar to the capacitive touchscreen, this captive fingerprint sensor measures your finger by using human conductivity, creating an...
− +
-20%
RedBot - Robotic Development Platform
$39.95 $49.95  
6 pc(s)
The RedBot Mainboard is a robotic development platform that works with the Arduino IDE. The RedBot is a motor driver and Ardiuno combination with various headers and connections, eliminating the need to stack multiple shields. By using the RedBot accessory boards and your own chassis, you...
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Adjustable Focus Lens
$39.00 $48.75  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
-15%
CAN-BUS Shield
$38.25 $45.00  
1 pc(s)
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output...
− +
DC & Stepper Motor HAT for Raspberry Pi
$38.00  
Out-of-stock
Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, this HAT uses...
Out-of-stock
Flexiforce Pressure Sensor - 25lbs
$38.00  
4 pc(s)
This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but the resistance does not change while being flexed. Resistance changes only when...
− +
Flexiforce Pressure Sensor - 1lb
$38.00  
1 pc(s)
This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but the resistance does not change while being flexed. Resistance changes only when...
− +
-20%
3.5" Resistive Touchscreen LCD + Pre-configured 16GB microSD Card For RaspberryPi
$37.60 $47.00  
7 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 3.5 inches 480x320 high resolution LCD display with resistive touchscreen, engineered specifically to let you quickly attached the...
− +
vRTCam - Remote Controller w/Wifi Video - Wide Angle Lens
$37.50  
8 pc(s)
Looking for a device that allows you to control your robot and at the same time to see what the robot sees on your mobile phone? Look no further than this vRTCam from SGBotic. The vRTCam is designed for use with a mobile phone as remote controller with minimum setup. It is unique in a...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
Adafruit DC Motor + Stepper FeatherWing Add-on
$36.75  
7 pc(s)
This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). It features a fully-dedicated PWM driver chip that handles all the motor and speed controls over I2C. Since the FeatherWing only...
− +
Negatron DC-DC Converter
$36.50  
4 pc(s)
Negatron is a buck-boost converter that takes a positive voltage and turns it into a negative voltage that you can use with amplifier circuits and more. The output is adjustable from -1.3V to -12V. Negatron is also able to step up/step down the magnitude of the voltage. For example,...
− +
Cool White LED Flexi-Strip - 5V (Bare, 5 meters)
$36.00  
3 pc(s)
These single color LED strip feature 60 ultra bright cool white LEDs on one meter. As these are bare LED strips that have no protective coating, your project won't be water proof but there is access to each LED and each strip length can be easily modified. Each of these strips need a 3V to 5V...
− +
-25%
LiPower Shield
$36.00 $48.00  
2 pc(s)
Is there anything an Arduino can't do? Well, for one, most of them can't be powered directly from a 3.7V LiPo battery; much less charge and monitor that battery. The SparkFun LiPower Shield takes care of this by combining the functionality of two of our favorite battery power boards: the...
− +
-20%
Raspberry Pi Zero Mini Camera - 160 Degree 60mm
$36.00 $45.00  
5 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
-20%
Raspberry Pi Zero Mini Camera - 72 Degree 150mm
$36.00 $45.00  
5 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
3.3V, 2.5A Step-Down Voltage Regulator D24V25F3
$35.00  
10 pc(s)
This D24V25F3 synchronous buck voltage regulator takes an input voltage of up to 38 V and efficiently reduces it to 3.3 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.5 A and features reverse voltage protection. Typical efficiencies of 80%...
− +
DELink 2 USB Link For Kangaroo PID Motion Controller
$35.00  
4 pc(s)
The DELink 2 USB Link is the perfect compliment to our Kangaroo x2 self-tuning PID motion controller. Coupled with the DEScribe software, you can upload / download settings or reset the Kangaroo to factory defaults. Utilizing the easy-to-use USB bus, changing the settings on your Kangaroo...
− +
Feather M0 Adalogger
$34.95  
2 pc(s)
Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 Adalogger - an 'all-in-one' Cortex M0 datalogger (or data-reader)...
− +
Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685
$33.85  
1 pc(s)
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you...
− +
M5Stack Module - M5Camera (Fisheye Lens)
$33.00  
8 pc(s)
M5Camera is a development board for digital image processing. It can be programmed for facial recognition, webcam or other image processing applicaton. It features an ESP32 chip with 4M Flash and 520K RAM, and a 2-Megapixel image sensor (OV2640). It also comes with 4 Mbyte PSRAM for extra...
− +
MakerBeam Hinge Bearing
$32.50  
3 pc(s)
Hinge bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. The 3mm inner diameter makes is easy to mount on a M3 bolt. Trebuchet movement is possible with the added copper saddle band clips,...
− +
micro:bit Flex Sensor
$32.50  
4 pc(s)
This micro:bit Flex Sensor is specifically designed for micro:bit to detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. This sensors are easy to use. It will vary its resistance depending on how much it...
− +
-20%
Raspberry Pi Zero Mini Camera - 120 Degree 60mm
$32.00 $40.00  
2 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
-20%
Raspberry Pi Zero Mini Camera - 72 Degree 60mm
$32.00 $40.00  
5 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
-20%
ZX Distance and Gesture Sensor
$31.95 $39.90  
2 pc(s)
The ZX Distance and Gesture Sensor is a touchless sensor that is capable of looking for simple gestures. Developed in conjunction with XYZ Interactive , the sensor uses their GestureSense® technology to recognize the distance of an object away from the sensor up to about 12 inches (30cm,...
− +
-10%
Big Easy Stepper Motor Driver
$31.50 $35.00  
1 pc(s)
The Big Easy Driver, designed by Brian Schmalz , is a stepper motor driver board for bi-polar stepper motors up to 2A/phase. It is based on the Allegro A4983 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of...
− +
-15%
Ardumoto - Motor Driver Shield
$31.00 $36.50  
1 pc(s)
The Ardumoto Shield is a dual-motor controller for Arduino. Based on the L298 H-bridge, the SparkFun Ardumoto can drive two DC motors up to 2A per channel. Combined with an Arduino, the Ardumoto makes a fantastic controller platform for RC vehicles or even small autonomous robots. It's now...
− +
-10%
SparkFun Photodetector Breakout - MAX30101 (Qwiic)
$30.15 $33.50  
3 pc(s)
The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light...
− +
-10%
SparkFun Thing Plus - Artemis
$30.15 $33.50  
1 pc(s)
If you are looking for a board that (almost) does it all, look no further! The SparkFun Artemis Thing Plus takes the popular Thing Plus footprint and adds in the powerful Artemis module for ultimate functionality. Fully compatible with SparkFun's Arduino core, the modern USB-C connector makes...
− +
Copper Tape - Conductive Adhesive, 50mm (20 Meters)
$29.95  
5 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
Soil Moisture /Temperature Sensor - SHT10
$29.95  
1 pc(s)
Take your gardening project to the next level with a SHT-10 based soil sensor. The sensor includes a temperature/humidity sensor module from Sensiron in a sinter metal mesh encasing. The casing is weatherproof and will keep water from seeping into the body of the sensor and damaging it, but...
− +
-23%
Air Quality Breakout - CCS811
$29.90 $38.90  
2 pc(s)
The CCS811 Air Quality Breakout is a digital gas sensor solution that senses a wide range of Total Volatile Organic Compounds (TVOCs), including equivalent carbon dioxide (eCO2) and metal oxide (MOX) levels. VOCs are often categorized as pollutants and/or sensory irritants and can come...
− +
Magician Rover Chassis Kit v2
$29.90  
4 pc(s)
The Magician Rover Chassis v2 is our latest robot platform from Dagu. It features two gearmotors with 65mm wheels and a rear caster. The chassis plates are injection molded with a wide variety of mounting holes for sensors, controllers, power, etc. Simply bolt the two plastic platforms...
− +
Flex Sensor 4.5"
$29.50  
1 pc(s)
A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Glove . The resistance of the flex sensor changes when the metal pads...
− +
-42%
AutoDriver - Stepper Motor Driver
$29.50 $51.00  
1 pc(s)
This AutoDriver makes it easy to put the L6470 Stepper Driver (a.k.a "dSPIN") to work in your project. Simply connect your motors and your SPI-capable microcontroller and get steppin'! STMicro's L6470 is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent...
− +
EE Component Pack #1
$29.50  
1 pc(s)
This is a custom made component kit for the following NUS Executive Education program: Architecting IoT Solutions Design Intelligent Edge Computing The kit includes: 1x Breadboard Medium Self-Adhesive, 830 tie-in points 1x 40-Pin Rainbow Wire, 20cm - M/F...
− +
-48%
Fio v3 - ATmega32U4
$29.50 $56.90  
1 pc(s)
The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4. While the Fio v3 is not yet compatible with the Arduino v1.0 IDE, it's still a very capable XBee-ready development board. The JST-connector and 3.3v system voltage make this a great development tool for...
− +
MakerBeam Hinge Kit
$29.50  
11 pc(s)
1 bag of MakerBeam hinges kit contains 8 hinges and 4 axes (ISO7380, M3, 14mm, A2) and 4 self locking nuts (DIN985).The hinges were specially designed to make a hinge or to mount a beam at any angle you would like.
− +
MakerBeam Bearing
$29.00  
8 pc(s)
Stainless steel bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. If you fit it to a MakerBeam it will extend about 1.5mm from the edge of the beam. The 3mm inner diameter makes is easy to...
− +
Peristaltic Liquid Pump
$28.99  
Out-of-stock
Move fluid safely from here to there with this very nice little pump. Unlike most liquid pumps, this is a peristaltic type - the pump squishes the silicone tubing that contains the liquid instead of impelling it directly . The upshot? The pump never touches the fluid which makes this an...
Out-of-stock
SRF05 Low Cost Ultrasonic Range Finder w/Header
$28.90  
2 pc(s)
The SRF05 is an evolutionary step from the SRF04, and has been designed to increase flexibility, increase range, and to reduce costs still further. As such, the SRF05 is fully compatible with the SRF04. Range is increased from 3 meters to 4 meters. A new operating mode (tying the mode...
− +
STM32F411CEU6 Black Pill Development Board
$28.50  
5 pc(s)
STM32F411CEU6 Black Pill Development Board is an updated version of the popular STM32 Blue Pill. This newer version features a more powerful Core-M4 based ARM CPU running at 100 MHz. It has numerous enhanced features including a 512KB flash, 128KB SRAM memory, a Floating Point Unit, and more...
− +
1 2 3 4 5 6 7 8
2 - 9