Delivery fee

New items

1 2 3 4 5 6 7 8 9
Sort by Price: Low to High
96 Per Page
TT Gear Motor - 200RPM
$4.50  
6 pc(s)
These inexpensive and reliable TT Gear Motors are an easy, low-cost way to get your projects moving. These gear motors require a voltage of 3-6VDC with a no load current of less than 150mA at 3V and possess a stall torque of 0.8kg.cm at 6V, a gearbox ratio of 48:1, and it comes with 2 x 200mm...
− +
-55%
3DR Safety Switch for PX4 / Pixhawk
$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...
− +
Mini Servo / ESC Tester
$4.50  
1 pc(s)
The Mini Servo / ESC Tester allow the user to test and exercise servos and set up a mode without requiring the use of a transmitter and receiver. It is easy to use and can test most servo technical parameters. It allows the user to control a servo directly to determine its neutral position...
− +
-50%
Flash Memory - microSD 1GB
$4.50 $9.00  
78 pc(s)
This is a 1 GB microSD media card. Perfect for massive datalogging in a minute amount of space. These microSD cards have a simple to use SPI interface allowing any micro to read and write data in a very large 1 gigabyte storage array. This product is guaranteed to work in products that use a...
− +
MQ-7 Gas Sensor (Carbon Monoxide)
$4.50  
2 pc(s)
This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to Carbon...
− +
Miniature PIR Motion Sensor
$4.50  
6 pc(s)
This miniature PIR sensor is designed for motion detection. It uses pyroelectric sensor to detect motion by measuring changes in the infrared levels emitted by surrounding objects. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that...
− +
Timing Pulley - Shaft Mount (30T, 5mm Bore)
$4.50  
4 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 30 teeth with a gear pitch of 2mm, an outer diameter of 21.6mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 30...
− +
2.4GHz / 5GHz Duck Antenna RP-SMA w/ IPEX Interface Cable
$4.50  
11 pc(s)
2.4GHz/5GHz Duck Antenna with regular RP-SMA RF connector and IPEX interface cable for connecting to our dual mode wireless module . Includes: 1x Antenna 1x IPEX Interface cable Features: Type: Omni-Directional Frequency: 2400~2500MHz/5150~5850MHz Gain: 3dBi...
− +
Security Alarm With LDR (Soldering Kit)
$4.50  
5 pc(s)
This fun little soldering kit allows you to make a light activating security alarm. Using an LDR (Light dependent resistor) and an NPN transistor, the LED and buzzer will activate if light shinning on the LDR is above the pre-set threshold. The kit comes with a hardcopy construction guide....
− +
MQ-8 Gas Sensor (Hydrogen)
$4.50  
2 pc(s)
This is a simple-to-use hydrogen gas sensor, suitable for sensing hydrogen concentrations in the air. The MQ-8 can detect hydrogen gas concentrations anywhere from 100-10000ppm. This sensor has a high sensitivity and fast response time. The sensitivity of the sensor can be adjusted by...
− +
Timing Belt - 2GT (per meter)
$4.70  
11 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm and 2mm pitch....
− +
Timing Belt - 2GT (Length 110mm)
$4.70  
5 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 110mm,...
− +
-50%
LilyPad Protoboard Large
$4.75 $9.50  
1 pc(s)
This is a large board for prototyping through hole components with the LilyPad system. There are an array of pins all shorted together with 10mil traces. This allows for quick and easy prototyping - all you have to do is cut the traces between holes you don't want connected! Standard 0.1"...
− +
-20%
LilyPad LED Red (5pcs)
$4.75 $5.95  
4 pc(s)
This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-20%
LilyPad LED Pink (5pcs)
$4.75 $5.95  
7 pc(s)
Here is a simple 5 pack of pink LEDs for LilyPad, or whatever else you can dream up. Light up the night! LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting...
− +
-20%
LilyPad LED Blue (5pcs)
$4.75 $5.95  
3 pc(s)
This is a simple pack of five Blue LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
-20%
LilyPad LED White (5pcs)
$4.75 $5.95  
Out-of-stock
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
Out-of-stock
-20%
LilyPad LED Yellow (5pcs)
$4.75 $5.95  
7 pc(s)
This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
− +
Timing Pulley - Shaft Mount (36T, 5mm Bore)
$4.80  
2 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 36 teeth with a gear pitch of 2mm, an outer diameter of 25.4mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 36...
− +
M5Stack Module - HUB
$4.80  
9 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack HUB Module is used for GROVE port expanding. It allows three I2C devices with unique address to connect to M5Stack Core. This HUB is...
− +
M5StackC HAT - PIR Motion Sensor
$4.80  
10 pc(s)
PIR HAT is a M5StackC compatible PIR Motion Sensor. This is a pyroelectric sensor that detects motion by measuring changes in the infrared levels emitted by surrounding objects. When the motion is detected, the sensor will output HIGH and last for two seconds until the next detecting...
− +
Alligator Test Leads (Pack of 10) - Small
$4.80  
18 pc(s)
Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them,...
− +
1.27mm to 2.54mm Interface Board
$4.80  
3 pc(s)
This simple interface board convert 20pins 1.27mm (0.05") pin header to 2.54mm (0.1") pin header. It works with J-Link EDU Mini Programmer .
− +
Raspberry Pi GPIO Tall Header w/Extended Pins- 2x20
$4.80  
33 pc(s)
This extra-tall stackable 40-pin female header features two rows of 20 pins spaced with a 0.1″ (2.54 mm) pitch. It includes three 0.1″-thick spacers for additional clearance, and the extended pins allow multiple units to be stacked together. The 2×20 size is notably used on the Raspberry Pi...
− +
Micro Servo - 9g
$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....
− +
Timing Belt - 2GT (Length 112mm)
$4.90  
2 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 112mm,...
− +
5V Stepper Motor w/ULN2003 Driver
$4.90  
3 pc(s)
This small stepper is a great way to get things moving, especially when positioning and repeatability is a concern. The stepper motor has five color-coded wires allow it to be controlled by both unipolar and bipolar stepper motor drivers. All five wires are used when connect to a unipolar...
− +
-20%
Keypad - 16 Button (Alphanumeric)
$4.95 $6.20  
2 pc(s)
This is a basic 16 button keypad that has been designed for easy user input and functionality. The buttons are set up in a matrix format which allows a microcontroller to 'scan' the 8 output pins to see which of the 16 buttons is being pressed. Each of the keypad's 16 buttons has been...
− +
Hook-up Wire - Red (22 AWG)
$4.95  
5 pc(s)
Standard 22 AWG solid Red hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes in small spools of 25'.
− +
Hook-up Wire - White (22 AWG)
$4.95  
3 pc(s)
Standard 22 AWG solid White hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes in small spools of 25'.
− +
Humidity and Temperature Sensor - DHT11
$4.95  
1 pc(s)
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires...
− +
USB Type-C Cable with Switch - 1.5 meter
$4.95  
16 pc(s)
This USB to Type-C Cable with switch is 1.5 meter long and is the perfect hard on/off power switch for your Raspberry Pi 4 or any devices that has a Type-C port. Note : The data lines are not connected, so it's mostly just good for powering and charging devices. Dimensions:...
− +
Copper Tape - Conductive Adhesive, 5mm (20 Meters)
$4.95  
10 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
Low Speed Gearmotor - 5V 10rpm
$4.99  
4 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...
− +
Pi Case for Raspberry Pi 4 - Translucent
$4.99  
12 pc(s)
This translucent enclosure protect the Raspberry Pi 4 from things like rogue wires that might short it out while still allowing access to the ports! Simply snap the Pi 4 into the bottom half of the enclosure, snap the two sides together and then secure with four screws. This...
− +
Low Speed Gearmotor - 3V 20rpm
$4.99  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...
− +
Low Speed Gearmotor - 5V 5rpm
$4.99  
3 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
− +
Wire Bundle 8cm - M/M (Approx. 49pcs)
$5.00  
6 pc(s)
Stranded core wires with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Approx. 100pcs. 8cm Length.
− +
10-Pin Alligator Clip to Male Rainbow Wire
$5.00  
9 pc(s)
For bread-boarding with unusual non-header-friendly surfaces, these rainbow wire will be your best friends! No longer will you have long strands of alligator clips that are grabbing little wires. These wires have a premium male header on one end, and a grippy mini alligator clip on the other....
− +
10-Pin Alligator Clip to Female Rainbow Wire
$5.00  
9 pc(s)
For bread-boarding with unusual non-header-friendly surfaces, these rainbow wire will be your best friends! No longer will you have long strands of alligator clips that are grabbing little wires. These wires have a premium female header on one end, and a grippy mini alligator clip on the...
− +
-21%
Tweezers - Straight (ESD Safe)
$5.00 $6.30  
1 pc(s)
These are nice, solid curved tweezers. They have a very fine tip which allows you to pick up very small parts with precision. This is a great tool to have if you're working with surface mount components or anything with very small parts. The ESD-safe coating will also help prevent...
− +
Timing Belt - 2GT (Length 122mm)
$5.00  
6 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 122mm,...
− +
Mini Lock-style Solenoid - 12VDC
$5.00  
8 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Lock-style Solenoid - 6VDC
$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Vinyl End Caps for MakerBeam 15x15mm Profile (black, 4pcs)
$5.20  
7 pc(s)
End caps for MakerBeam in 15x15mm profile black vinyl. We finally can give our beams little feet. This specially desinged end caps will help to protect your desktop or to prevent your MakerBeam project from slipping away. It also reduces vibrations for your construction. They...
− +
-30%
WS2812 RGB Ring - 24 LED
$5.25 $7.50  
130 pc(s)
Round and round and round they go! 24 ultra bright smart RGB LED are arranged in a circle with 86mm outer diameter. The rings are 'chainable' - connect the output pin (DO) of one to the input pin (DI) of another. Use only one microcontroller pin to control as many as you can chain together!...
− +
Hook-up Stranded Wire - White (22 AWG)
$5.30  
2 pc(s)
Standard 22 AWG stranded White wire. Use this for soldering wire or any project in which you need flexible wire. Stranded wire is recommended for projects where the wire has a bend or stress point. Comes in small spools of 25'
− +
Hook-up Stranded Wire - Red (22 AWG)
$5.30  
2 pc(s)
Standard 22 AWG stranded red wire. Use this for soldering wire or any project in which you need flexible wire. Comes in small spools of 25'.
− +
M5Stack Module - Angle
$5.40  
10 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Angle Module is a rotary switch Unit, simply having a 10K potentiometer inside. This unit can be used for Continuous singal dialing...
− +
-30%
Push Button Assortment Pack of 5 (Assembled)
$5.50 $7.85  
30 pc(s)
These push buttons are great for all sorts of projects. This assortment comes with 5 different colors and the button is soldered to a breakout board with a 10K pull-up resistor and 2.54mm male header. The colored caps are removable . The dimension of the button is 12mm x 12mm.
− +
-31%
LilyPad Reed Switch
$5.50 $7.95  
1 pc(s)
The LilyPad Reed Switch is a simple breakout for a reed switch that will make it easy to use in e-textiles circuits in exactly the same manner that you can currently use the LilyPad Button and Switch. In order to make it more durable for wearable use, we've used a different style of reed switch,...
− +
Flex Cable for Raspberry Pi Camera - 1 Meter
$5.50  
2 pc(s)
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 1 Meter long. Each order comes with one cable, Pi...
− +
-31%
LilyPad RGB LED
$5.50 $7.95  
3 pc(s)
Blink any color you need! Use the LilyPad RGB LED board as a simple indicator, or by pulsing the red, green, and blue channels, you can produce a broad variety of colors. Each of the colors in the RGB LED are connected to one of the sew tabs on the board labeled R, G, and B. The color...
− +
Basic Temperature-Humidity Sensor Breakout - DHT11
$5.50  
6 pc(s)
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires...
− +
Alligator Test Leads (Pack of 10) - Medium
$5.50  
8 pc(s)
Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them,...
− +
J1962 ODBII To Open End - Male 1.5M
$5.50  
7 pc(s)
OBDII is an on board diagnostics standard that is used on a large variety of cars. OBD-II provides access to numerous data from the engine control unit (ECU) and offers a valuable source of information when troubleshooting problems inside a vehicle. If you're not sure if your car works with...
− +
L298 Dual Motor Driver Module 2A
$5.50  
3 pc(s)
This dual motor driver is based on the L298N heavy-duty dual H-bridge controller, which can be used to drive two DC motors at up to 2A each, with a voltage between 5 and 35V DC - or one stepper motor or 2 solenoids with ease. The driver has a nice heatsink to keep the L298N cool and all...
− +
Diagonal Cutters
$5.80  
3 pc(s)
Mini Diagonal Cutters. These are great little cutters! A must have for clipping leads and extra solder tails. 4" long.
− +
Plastic Case for V2 Micro:bit - Black
$5.80  
1 pc(s)
Note: BBC micro:bit is NOT included. The BBC micro:bit is everybody's favorite little controller: the last thing you want is for something bad to happen to it. Why not protect it with one of these plastic cases? These cases protect the micro:bit from things like rogue wires that...
− +
Micro Servo - 9g (360° Full Rotation)
$5.90  
Out-of-stock
Here is a simple, low-cost, high quality continuous 360° full-rotation servo motor for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as...
Out-of-stock
Solder Lead Free - 15-gram Tube
$5.90  
5 pc(s)
This is you basic tube of unleaded (Pb-free) solder with a 60/40 no clean, water soluble resin core. 0.031" gauge and 15 grams. Mix: 96.5% tin / 3.0% silver / 0.5% copper
− +
Graphic LCD 96x68 - HX1230
$5.90  
5 pc(s)
The HX1230 LCD is a basic graphic LCD screen originally intended for as a cell phone screen. It uses the HX1230 controller. The HX1230 is a low power CMOS LCD controller/driver, designed to drive a graphic display of 68 rows and 96 columns. The HX1230 requires four I/O pins for interfacing and...
− +
Mini MP3 Module
$5.95  
5 pc(s)
The Mini MP3 Module is a small, low-cost mp3 module with a simplified audio output that can be connected directly to a speaker or an earphone jack. The module can be used as a stand-alone module with attached battery, speaker, and push buttons or used in combination with a microcontroller or...
− +
-21%
LPG Gas Sensor - MQ-6
$5.95 $7.50  
1 pc(s)
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing  LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has a high sensitivity and fast response...
− +
2-Layers Storage box
$5.95  
1 pc(s)
2-layers storage box for components, development boards, wires, etc. The dividers in the bottom layer can be removed. Dimensions (external) : 230mm(L) x 160mm(W) x 60mm(H)
− +
Copper Tape - 10mm (20 Meters)
$5.99  
9 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is...
− +
-20%
TEMT6000 Breakout Board
$6.00 $7.50  
3 pc(s)
Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don't. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin. Documents: Datasheet Wiring Example...
− +
-50%
LilyPad SimpleSnap Protoboard
$6.00 $12.00  
3 pc(s)
The LilyPad SimpleSnap Protoboard is a new, easy way to create e-textiles projects with LilyPad that are modular and can be disassembled or broken down, it's also a great way to prototype! The SimpleSnap Protoboard is made to connect to the SimpleSnap main board so that the board is...
− +
M5StackC HAT - Speaker
$6.20  
7 pc(s)
SPK HAT is a M5StackC compatible speaker. This HAT module features a PAM8303 mono audio amplifier. PAM8303 is a class D amplifier, able to deliver up to 3 Watts into 4 ohm impedance speakers. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over...
− +
-20%
RF Link Transmitter - 315MHz
$6.30 $7.90  
4 pc(s)
These wireless receivers work with our 315MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
-30%
Force Sensitive Resistor - Small (FSR400) - Male Pin Header
$6.30 $9.00  
61 pc(s)
This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR,...
− +
-20%
Mifare 13.56MHz RC522 RFID Card Reader (3.3V Supply)
$6.35 $7.95  
5 pc(s)
MFRC522 is the highly integrated RFID card reader which works on non-contact 13.56MHz communication. Designed by NXP as a low power consumption, low cost and compact size read and write chip, this MFRC522 is the best choice in the development of portable hand-held devices. It supports...
− +
-20%
Resistor Kit - 1/4W 1% (600 total)
$6.40 $8.00  
9 pc(s)
Don't you hate it when you're in the middle of a build and you don't have a certain value of resistor? Don't let it happen again with this resistor kit. This kit contains a resistor color code chart and 20 each of 30 standard value 1/4 Watts resistors with 1% tolerance. It's perfect for starting...
− +
M12 (S-Mount) lens - 8mm
$6.45  
12 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 8mm fixed lens with IR Cut Filter provides...
− +
M12 (S-Mount) lens - 12mm
$6.45  
3 pc(s)
M12 Lenses, also referred to as S-Mount Lenses, are compact imaging lenses designed for use with many small format cameras. They are ideal for environments where space is limited. Designed for use in micro sensor board cameras, this low cost 12mm fixed lens with IR Cut Filter...
− +
Outdoor Type 2 NFC Tag - NTAG213 (Diameter 40mm)
$6.50  
1 pc(s)
This disc-shaped, waterproof tag contains a small NTAG213 RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple centimeter away.. The housing will withstand rugged conditions and is designed for outdoor use. It can be secured with screws. You can...
− +
Non-Isolated Single Relay Module For 3V Controller
$6.50  
1 pc(s)
This single channel Relay Module is specially designed for low-voltage devices and works well with 3.3V power supply. It can be used to control the lighting, electrical and other equipments through the digital IO port. The module comes with on-board back EMF protection to eliminate the...
− +
-29%
Tactile Button Assortment Pack of 12
$6.50 $9.10  
19 pc(s)
These tactile buttons are great for all sorts of projects. This assortment comes with 2 of each of 6 different colors for a total of 12 buttons. The colored caps are removable and the buttons fit into breadboards. See the drawing below for exact dimensions. Documents: Drawing
− +
-27%
LilyPad Buzzer
$6.50 $8.85  
2 pc(s)
This is a small buzzer for the LilyPad system. Use 2 I/O pins on the LilyPad main board and create different noises based on the different frequency of I/O toggling. Loud enough to hear inside a pocket but not obtrusively loud. Please note: This is an inductive buzzer meaning that is will act...
− +
-6%
USB Type A Female Breakout
$6.50 $6.95  
1 pc(s)
This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you. Dimensions : 1.02 x 0.9" (26.06 x 22.93mm)...
− +
RFID Button - 16mm - 125kHz
$6.50  
4 pc(s)
This is a simple, thumbnail-size RFID tag. These tags are great for sensing presence, identification, etc., and they're small, so they can be easily sewn into clothing or inserted into enclosures. Each tag comes with a unique 32-bit ID code and is not reprogrammable. The carrier frequency of...
− +
Needle Nose Pliers
$6.80  
3 pc(s)
Mini Pliers. These are great little pliers! A must have for any hobbyist or electrical engineer. Crucial for inserting devices into bread boards and bending pins. 4" long.
− +
Micro Metal Gearmotor Bracket Extended Pair
$6.90  
4 pc(s)
This compact bracket enables convenient mounting of popular, Sanyo-style miniature metal gearmotors. The plastic bracket encloses the otherwise exposed gears, and the mounting tabs capture the nuts for easy installation. This version has mounting tabs that allow for use with the Pololu Wheel...
− +
Copper Tape - Conductive Adhesive, 10mm (20 Meters)
$6.90  
Out-of-stock
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
Out-of-stock
Outdoor Type 2 NFC Tag - NTAG213 (Diameter 52mm)
$6.95  
5 pc(s)
This disc-shaped, waterproof tag contains a small NTAG213 RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple centimeter away.. The housing will withstand rugged conditions and is designed for outdoor use. It can be secured with screws. You can use...
− +
Wind Power Kit (Soldering Kit)
$6.95  
5 pc(s)
This Wind Power Kit is designed to show students how alternative energy is created by harnessing the power produced by the wind. The kit has a high efficient generator that can produce useful electricity at low speed. It can generate sufficient electricity to light up a LED by blowing onto the...
− +
-30%
Type-K Thermocouple probe - 150mm
$6.99 $10.00  
10 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 150mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-36%
Type-K Thermocouple probe - 200mm
$6.99 $11.00  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 200mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-7%
Type-K Thermocouple probe - 50mm
$6.99 $7.50  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 50mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
Pulse Oximeter & Heart-Rate Sensor - MAX30102
$6.99  
4 pc(s)
MAX30102 Sensor is an integrated pulse oximetry and heart-rate monitor module. It is equipped with a red and IR LEDs as well as a very sensitive photon detector. The idea is to pulse the different LEDs, then detect what shines back. Based on the reflected signature it's possible to measure...
− +
-22%
Type-K Thermocouple probe - 100mm
$6.99 $9.00  
7 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 100mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-30%
Basic 8x2 Character LCD - Black on Green 5V
$7.00 $9.95  
3 pc(s)
This is a basic 8 character by 2 line display with black text on green background. The screen utilizes the extremely common HD44780 parallel interface chipset. Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes LED backlight....
− +
-20%
RF Link Receiver - 4800bps (315MHz)
$7.25 $9.10  
6 pc(s)
These wireless receivers work with our 315MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
Wind Power Kit (Partially Assembled)
$7.45  
7 pc(s)
This Wind Power Kit is designed to show students how alternative energy is created by harnessing the power produced by the wind. The kit has a high efficient generator that can produce useful electricity at low speed. It can generate sufficient electricity to light up a LED by blowing onto the...
− +
MakerBeam M3 Hex Nut Driver
$7.50  
3 pc(s)
This high quality hex nut driver (5,5mm) is a standard item in our MakerBeam Starter Kit. Work with both standard nuts and Cap nuts.
− +
-20%
Load Sensor - 50kg
$7.90 $9.90  
12 pc(s)
This load cell / sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. Each straight bar load cell is made from an aluminum-alloy and is capable of measure up to about 50kg. Documents : Specifications Load Sensor Tutorial (NerdKits)
− +
1 2 3 4 5 6 7 8 9