Delivery fee

New items

1 2 3 4 5 6 7 8 9
Sort by Price: High to Low
96 Per Page
NVIDIA JetBot Mounting Kit
$3.50  
8 pc(s)
This mounting kit is intended for use with the NVIDIA JetBot robot. It includes the necessary screws and nuts to secure the Jetson Nano, motors, camera, etc., to the 3D printed chassis. Kit includes: 4x M3*25 Phillips pan head machine screw (stainless steel) 4x M3 nuts...
− +
7-Segment Green LED - 0.8" Digit Height
$3.50  
5 pc(s)
Your basic 7-segment LED, Common anode. Digit height is 0.8" (20.4mm). Overall height is 27.7mm. Documents: Datasheet Arduino Library
− +
Bi-axial Gear Motor (1:94)
$3.50  
1 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 400mA while possessing a gearbox ratio of 1:94 and a wheel...
− +
Bi-axial Gear Motor (1:143)
$3.50  
4 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 660mA while possessing a gearbox ratio of 1:134 and a wheel...
− +
Large Breadboard Self-Adhesive, 830 Tie-In Points
$3.50  
7 pc(s)
This is a medium sized breadboard with 830 tie-points, self-adhesive backing and two power rails on both sides. Dimensions: 165(L) x 54 (W) x 9(H) mm
− +
RGB LED Module - 8mm
$3.45  
38 pc(s)
The RGB LED module allows for individual control of red, green, or blue colors all in a single module. Features: 8mm RGB LED 3.3V and 5.0V compatible
− +
-50%
Interface Cable RP-SMA to U.FL
$3.45 $6.95  
4 pc(s)
This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the DPAC 802.11 modules. Dimensions: 4" Length
− +
HC-SR04 Low Cost Ultrasonic Module (5V Supply)
$3.45  
15 pc(s)
HC-SR04 ultrasonic sensor provides a very low-cost and easy method of distance measurement. This sensor measures distance using sonar. An ultrasonic (well above human hearing) pulse is transmitted from the unit and distance-to-target is determined by measuring the time required for the...
− +
Vibration Motor Module
$3.25  
16 pc(s)
This small vibratory motor module is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. The on-board MOSFET driver allows the module to interface directly to microcontroller. Features : Operating voltage:...
− +
8-channel Bi-directional Logic Level Converter - TXS0108
$3.20  
1 pc(s)
If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The 8-channel Bi-directional Logic Level Converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V...
− +
-50%
SOIC to DIP Adapter 28-Pin
$3.15 $6.30  
22 pc(s)
Low-cost basic SOIC break out boards. These are custom PCB boards that interface standard SOIC devices to standard .1" (2.54mm) headers. 28-SOIC: Standard .6" spacing between pins. Will fit directly into a standard width (600 mil) DIP socket. For wide ICs (memories, drivers, 74s,...
− +
-50%
SSOP to DIP Adapter 28-Pin
$3.15 $6.30  
14 pc(s)
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm)....
− +
4 x 18650 Battery Holder
$3.00  
7 pc(s)
Battery holder for four 18650 Lithium Ion batteries, terminated with ~150mm leads
− +
Infrared Receiver Diode (TSOP38238)
$3.00  
33 pc(s)
Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes. The TSOP38238 is a miniaturized receiver for infrared remote control...
− +
USB mini-B Cable - 50cm
$3.00  
3 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 50cm
− +
USB Extension Cable - 50cm
$3.00  
5 pc(s)
This is a 50cm long USB extension cable equipped with type A male connector on one end to plug into your computer and a type A female connector at the other that allows for a second USB cable to be inserted. This cable is perfect for adding a periphery that utilizes USB without having it...
− +
USB microB Cable - 50cm
$3.00  
Out-of-stock
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
Out-of-stock
-33%
RCA Video Cable - 6'
$3.00 $4.50  
1 pc(s)
RCA cables are super handy for moving analog signals around. This is a great way to connect a composite video capable device, like the Raspberry Pi, to a suitable display. They also come in handy if you want to hook up your old-school analog gaming consoles, you know it's always impossible to...
− +
-40%
USB microB Cable - 1.5 meter
$3.00 $5.00  
1158 pc(s)
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
− +
USB Cable A to B - 50cm
$3.00  
Out-of-stock
This is the classic. It's an A to B Male/Male type peripheral cable for printers and other large peripheral devices. Compatible with Arduino Uno and Arduino Mega. Dimensions: 50cm
Out-of-stock
Mini Submersible Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
4 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This Mini Submersible Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with tubing....
− +
Medium Breadboard White, 400 Tie-In Points
$2.95  
1 pc(s)
This is your tried and true white solderless breadboard. It has 2 power buses, 30 columns, and 10 rows - a total of 400 tie in points. All pins are spaced by a standard 0.1". The two sets of five rows are separated by about 0.3", perfect for straddling a DIP package over. The board accepts...
− +
Jumper Wires Premium 6" M/M Pack of 10
$2.95  
1 pc(s)
These are 155mm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Combine these with our female to female jumpers to create a male to female jumper. Multiple jumpers can be installed next to one another on a 0.1"...
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Blue
$2.95  
9 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
Barrel Jack Adapter - USB to 5.5mm
$2.95  
2 pc(s)
This is a simple cable that adapts from a USB port to a 5.5x2.1mm barrel connector, center positive. This cable allows the user to use a USB port on a computer, laptop, or on our cigarette power supply to provide our development boards with 5V. The USB specification limits current...
− +
UV 400nm Purple LED Clear Lens - 5mm (10 pcs)
$2.95  
45 pc(s)
These LEDs emit UV 'blacklight' in the UV spectrum so they are great for projects with fluorescent materials referred to as UV/blacklight-reactive or 'glow-in-the dark'. They are bright (350mcd) and have about a 20-degree LED beam. They go easily into a breadboard and come in a pack of ten so...
− +
Wheel for 5V Stepper Motor - 60mm Diameter
$2.95  
4 pc(s)
This wheel is designed specifically for our 5V stepper motor It comes with a rubber tread, and a press-fit design to make connecting super quick and easy. Note: Wheel only. Stepper motor not included. Wheel body: 56 x 8mm
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Green
$2.95  
3 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
ESP8266 WiFi Module Breakout Board - Assembled
$2.95  
2 pc(s)
This ESP8266 WiFi Module Breakout Board allows you to take the dual row header of the ESP-01 and make it breadboard friendly. This board is fully assembled. NOTE : ESP8266 WiFi Module not included.
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Red
$2.95  
9 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
Breadboard Power Supply 5V/3.3V
$2.95  
5 pc(s)
This Breadboard Power Supply Module plugs directly into a solderless breadboard and provides both 3.3V and 5V power directly to the breadboard power rails. The board accepts 7 to 12V DC input via the barrel jack or 5V via the mini-B USB port. It provides two regulated, fuse protected outputs...
− +
Mini Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
Out-of-stock
Looking for a battery powered liquid pump for your Micro:Bit project? This submersible Mini Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with...
Out-of-stock
T5577 RFID Tag - Read/Write 125kHz
$2.95  
8 pc(s)
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic T5577 RFID tag works in the 125kHz RF range and supports read/write operation. Note : This is a blank tag - its ID must be chosen and...
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Yellow
$2.95  
7 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
Solderless Adapter For WS2812 Fexi-Strip
$2.95  
19 pc(s)
This solderless adapter provides a convenient way to connect the WS2812 LED strip to your microcontroller. Although soldering is the best way to maintain a lasting connection, the solderless adapter is a great way to get your project going quickly without the hassle of soldering work. When...
− +
-25%
LilyPad Slide Switch
$2.95 $3.95  
2 pc(s)
This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to...
− +
USB Cable A to Pigtail - 30cm
$2.95  
25 pc(s)
The USB Cable A to Pigtail provides a convenient method for hard wire a USB Type A connecting to a device or terminal block. One end of the cable is fitted with a strain relief USB Type A connector. The other end of the cable has stripped and tinned leads. This cable is commonly used to power...
− +
-40%
USB 2.0 Cable A To Type-C - 1.5 meter
$2.95 $4.95  
403 pc(s)
The USB cable with type-C connector is perfect for USB to serial applications and for direct connection to basic microcontrollers (such as the SAMD21 or other with USB built-in). Supporting USB 2.0 speeds and charging up to 3A, this 1.5 meter cable is perfect for embedded enthusiast that need...
− +
Temperature Sensor - TMP36
$2.90  
375 pc(s)
The TMP36 are low voltage, precision centigrade temperature sensors. They provide a voltage output that is linearly proportional to the Celsius (centigrade) temperature. The TMP36 do not require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the −40°C...
− +
-50%
Standard LCD 16x2 - White on Blue 5V
$2.90 $5.80  
403 pc(s)
This is a standard 16 character by 2 line display. White text on Blue background. Utilizes the extremely common HD44780 parallel interface chipset ( datasheet ). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Features :...
− +
-25%
Raspberry Pi GPIO Tall Header - 2x20
$2.90 $3.85  
22 pc(s)
This 2x20 "tall" header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can encapsulate your Pi. This through-hole header has 40 0.1"-spaced pins and can...
− +
3-Pin Cable for Sharp Distance Sensors / SRF01 (w/Male Pin Header)
$2.90  
13 pc(s)
This 30cm cable has 26 AWG wires and a 3-pin female JST PH-style connector that works with Sharp Infra-red distance sensors: GP2Y0A02YK , GP2Y0A21YK and GP2Y0A41SK0F . The other ends of the wires are terminated with male pin header. The wire color scheme matches the Sharp distance sensor...
− +
Passive Piezo Buzzer w/Leads -13mm
$2.90  
3 pc(s)
This is a small 13mm round passive buzzer that operates around the audible 4kHz range. We drove it directly from a 3v to 5V Arduino or micro:bit to generate simple melody. The buzzer leads are terminated with male pin. Note : This passive buzzer requires a square wave (PWM) signal to...
− +
Piezo Element
$2.90  
2 pc(s)
Piezo elements come in handy when you need to detect vibration or a knock. You can use these for tap or knock sensors pretty easily by reading the voltage on the output. They can also be used for a very small audio transducer such as a buzzer. Documents: Datasheet...
− +
-21%
3 Buttons Membrane Keypad
$2.90 $3.65  
23 pc(s)
This 3 Buttons Membrane Keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, it only take up 4 I/O pins of the...
− +
6 x AA Battery Holder with Switch and Cover
$2.90  
15 pc(s)
Enclosed battery holder for six AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-5%
Type 2 NFC Card - NTAG216
$2.85 $3.00  
53 pc(s)
A white plastic PVC card that has an NTAG216 chip embedded inside. About the size of a credit card, this is a blank white NFC card that you can use with a card printer to customize. It houses an NTAG216 chip which holds up to 888 bytes of memory. Documents : Datasheet (NTAG216)...
− +
WS2812 RGB LED Stick (w/Male Pin Header)
$2.80  
12 pc(s)
This is the WS2812 Addressable RGB LED Stick with eight LEDs. The WS2812 is a addressable smart RGB LED that uses a single data line to control brightness and colour. The embedded constant-current driver keeps the LED brightness consistent even if the input voltage varies. There are...
− +
Male Crimp Pins for 0.1" Housings 20-Pack
$2.80  
6 pc(s)
These pins can be crimped on 22-28AWG wires and snapped into our crimp connector housings to create custom cables that are compatible with standard 0.1"-pitch headers and solderless breadboards. These male pins are sold in packs of 20.
− +
4 x AA Battery Holder with On/Off Switch, 3-Pin JST
$2.80  
5 pc(s)
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
9V Battery Holder with Switch & Barrel Jack
$2.80  
Out-of-stock
This is a 9V battery pack with on/off switch and terminated with a standard 5.5x2.1mm, center-positive barrel jack. Use this to battery-power your Arduino or other electronic projects. Battery & screw not included. Dimensions : 68mm x 33mm x 21mm Lead length: 12cm...
Out-of-stock
Female Crimp Pins for 0.1" Housings 20-Pack
$2.80  
13 pc(s)
These pins can be crimped on 22-28AWG wires and snapped into our crimp connector housings to create custom cables that are compatible with standard 0.1"-pitch headers and solderless breadboards. These female pins are sold in packs of 20.
− +
Voltage Regulator - 3.3V
$2.75  
20 pc(s)
This is the basic LD1117V33 voltage regulator, a low drop positive regulator with a 3.3V fixed output voltage. This fixed regulator provides a great amount of stability and protection for your project and with its on chip trimming this regulator is able to reach an output voltage tolerance...
− +
-50%
IOIO and Breadboard Holder
$2.60 $5.20  
1 pc(s)
This holder allows you to safely secure a IOIO development board and a self-adhesive breadboard in place to easily run jumper wires in between the two to form simple or complex prototyping circuits. Unlike it’s cousin, for the Arduino, this IOIO and breadboard holder has been made specifically...
− +
-20%
Solder Leaded - 15-gram Tube
$2.55 $3.20  
1 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
Timing Pulley - Shaft Mount (20T, 5mm Bore)
$2.50  
3 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 20 teeth with a gear pitch of 2mm, an outer diameter of 16mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 20...
− +
Photo Interrupter Module (T-Shape)
$2.50  
5 pc(s)
This Photo Interrupter Module is widely used in motor speed detection, pulse count, the position limit, etc. It will trigger a signal when light between the sensor's gap is blocked. It works with 3.3V to 5VDC, and gives a HIGH on DO pin when the beam is blocked, and a LOW output when...
− +
-31%
Illuminated Capacitive Switch Module - Red
$2.50 $3.60  
1 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
USB mini-B Cable - 30cm
$2.50  
4 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 30cm
− +
Orange and Clear Wheel for Bi-axial Gearbox Motor - 70mm Diameter
$2.50  
10 pc(s)
Need a wheel for your Bi-axial Gear Motor ? This Orange & Clear TT Motor Wheel is equipped with a nice, thick silicone tread and a press-fit design to make connecting super quick and easy. Make cute robots today with a couple of these orange wheels! Note : This wheel is only...
− +
WS2812 RGB LED Stick
$2.50  
1 pc(s)
This is the WS2812 Addressable RGB LED Stick with eight LEDs. The WS2812 is a addressable smart RGB LED that uses a single data line to control brightness and color. The embedded constant-currnet driver keeps the LED brightness consistent even if the input voltage varies. There are...
− +
-37%
Jumper Wire Kit
$2.50 $3.95  
1 pc(s)
This is a time saving kit of jumper wires - cut, stripped, and pre-bent for your prototyping pleasure. Included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each.
− +
3-Blade Nylon Boat Propeller - 40mm Diameter
$2.50  
11 pc(s)
Small fiber reinforced nylon propeller for boat, 3 blades and 40mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø40 x 18.5mm Center bore：1.9 mm
− +
Water Sensor - Large
$2.50  
2 pc(s)
This water sensor is designed to detect water, which can be used to sense water level and leakage. It works by using exposed copper traces to detect the presence of water droplets. The sensor board has a sensing area of 47 x 36mm. The on-board potentiometer is used to set the threshold for...
− +
DC Barrel Jack Adapter - Male
$2.50  
36 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution.
− +
USB microB Cable - 25cm
$2.50  
1 pc(s)
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
− +
-31%
Illuminated Capacitive Switch Module - Yellow
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
DC Barrel Jack Adapter - Female
$2.50  
4 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might be the simple solution.
− +
USB Cable A to B - 30cm
$2.50  
1 pc(s)
This is the classic. It's an A to B Male/Male type peripheral cable for printers and other large peripheral devices. Compatible with Arduino Uno and Arduino Mega. Dimensions: 30cm
− +
-31%
Illuminated Capacitive Switch Module - Green
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
Basic LED Soldering Kit
$2.50  
1 pc(s)
This fun little soldering kit is designed for beginners to practise their soldering skill. The kit features a pair of large LEDs which will light up when power is applied. Assembly is easy, and you should be able to do it in 10-15 minutes. The kit comes with: a construction...
− +
Rotary Encoder Breakout
$2.50  
Out-of-stock
The rotary encoder is a rotary input device that provides an indication of how much and in which direction the encoder has been turned. This 20-pulse Rotary Encoder Breakout has a nice 'clicking' feel and also has a push-button built into it so you can press onto the knob to close a separate...
Out-of-stock
4 x AA Battery Holder with Cover and Switch
$2.50  
3 pc(s)
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-31%
In-line power switch for 2.1mm barrel jack
$2.50 $3.60  
10 pc(s)
Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an...
− +
-50%
SSOP to DIP Adapter 8-Pin
$2.50 $5.00  
6 pc(s)
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm)....
− +
Photo Interrupter Module (Straight)
$2.50  
6 pc(s)
This Photo Interrupter Module is widely used in motor speed detection, pulse count, the position limit, etc. It will trigger a signal when light between the sensor's gap is blocked. It works with 3.3V to 5VDC, and gives a HIGH on DO pin when the beam is blocked, and a LOW output when...
− +
-31%
Illuminated Capacitive Switch Module - Blue
$2.50 $3.60  
2 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
9V Battery Holder with On/Off Switch, 3-Pin JST
$2.50  
5 pc(s)
Enclosed battery holder for 9V battery. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
Break Away Female Headers - Swiss Machine Pin
$2.50  
15 pc(s)
Single row of 40-holes, female header with swiss round machined pins. These units have very high quality round pins to accept and retain machine pin headers much better. Can be cut to size with a pair of wire-cutters. Standard 2.54mm spacing. Documents: 40-Pin Swiss Female...
− +
25mm Delrin Plastic Ball Bearings For Jetbot
$2.45  
35 pc(s)
Delrin ball bearings are made of a composite material well-suited for low- to moderate-load applications. This 25mm ball bearings is specially sourced for the Nvidia Jetbot. Dimensions: 25mm diameter
− +
ESP8266 WiFi Module Breakout Board
$2.40  
30 pc(s)
This ESP8266 WiFi Module Breakout Board allows you to take the dual row header of the ESP-01 and make it breadboard friendly. This board comes with the header and decoupling capacitor presoldered, but requires you to solder on the male pins. NOTE : ESP8266 WiFi Module not included.
− +
Photo Interrupter GP1A57HRJ00F Breakout Board
$2.35  
4 pc(s)
A simple breakout PCB for the GP1A57HR photo interrupter. This PCB has three connections for PWR, GND, and Signal. When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or anything else - SIG will go low (<0.4V)....
− +
-20%
RFID Tag - 125kHz
$2.35 $2.95  
19 pc(s)
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic RFID tag works in the 125kHz RF range and comes with a unique 40-bit ID. It is not re-programmable. This blank, smooth, and mildly...
− +
-50%
USB mini-B Cable - 1.5 meters w/Ferrite Bead
$2.25 $4.50  
53 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. The Ferrite Bead helps to eleminate EMI. Dimensions: 1.5 meter
− +
-50%
3DR Buzzer for PX4 / Pixhawk
$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm
− +
2 x AAA Battery Holder w/Switch and JST Connector
$2.25  
Out-of-stock
This 2xAAA Battery Holder with Switch and JST Connector is compatible with the BBC micro:bit. Supplied with ~150mm colour coded power leads and a JST connector at the end, this battery holder is light and can be attached to the back of BBC micro:bit cases. This battery holder features a lid...
Out-of-stock
Low Current DC Toy Motor w/ Male Lead Wire
$2.20  
10 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...
− +
Arduino Stackable Header Kit - R3
$2.20  
13 pc(s)
These headers are made to work with the Arduino Uno R3 and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers, enough to connect a R3 shield to an Arduino Uno R3....
− +
-31%
Tilt Sensor
$2.20 $3.20  
12 pc(s)
This basic tilt switch can easily be used to detect orientation. Inside the can are a pair of balls that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors,...
− +
Grove Universal 4 pin Connector - Straight Through-Hole (10pcs)
$2.15  
48 pc(s)
These 4-Pin straight through-hole 2mm pitch connectors are compatible with SeeedStudio's Grove cable.
− +
Grove Universal 4 pin Connector - Right Angle Through-Hole (10pcs)
$2.15  
44 pc(s)
These 4-Pin right angle through-hole 2mm pitch connectors are compatible with SeeedStudio's Grove cable.
− +
Water Sensor - Small
$2.10  
4 pc(s)
This Water Sensor is designed for water detection, which can be used in sensing the water level and leakage. This sensor works by having a series of exposed copper traces which will turn on the transistor when water droplets shot the copper traces. This sensor works with the digital I/O...
− +
Qwiic Cable - Male Jumper (200mm)
$2.10  
15 pc(s)
This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a Qwiic connector to a breadboard or an Arduino-based device's pins. The 28AWG wire's length is...
− +
Wheel for 9g Server Motor - 56mm Diameter
$2.00  
6 pc(s)
This wheel is designed specifically for our Micro Servo 9g - Full Rotation. It comes with a rubber tread, and a press-fit design to make connecting super quick and easy. Note: Wheel only. Servo not included. Wheel body: 56 x 8mm
− +
-20%
4 x AAA Battery Holder with Cover and Switch
$2.00 $2.50  
13 pc(s)
Enclosed battery holder for four AAA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
3-Blade Nylon Boat Propeller Set - 36mm Diameter
$2.00  
4 pc(s)
Small nylon propeller for port and starboard thruster. Featuring both left- and right-handed rotation. 3 blades and 36mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø36 x 18.5mm Center bore：1.9 mm
− +
1 2 3 4 5 6 7 8 9