Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
9 - 17
Sort Alphabetically: Z to A
48 Per Page
Mini Real Time Clock Module (DS3231) for Raspberry Pi
$11.95  
5 pc(s)
Unlike most computers, the Pi lacks a Real-Time Clock (RTC). This means the Pi doesn't know what time it is when powered on. While your Pi is connected to a network it will be able to set it's clock correctly using NTP ( Network Time Protocol ) server. Without a network connection your Pi...
− +
-50%
Mini Push Button Switch
$0.10 $0.20  
1043 pc(s)
Miniature Single Pole Single Throw switches. These are high quality momentary on switches. Perfect as a tactile reset switch. Mounts directly into standard bread boards. Rated up to 50mA. Documents : Datasheet (TSS-TC-0104)
− +
Mini Photocell (LDR - Light Dependent Resistor)
$1.00  
68 pc(s)
This is a very small photocell. A photocell changes (also called a photodetector , CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make great ambient light triggers (when light in the room turns on, do something)....
− +
Mini MP3 Module
$5.95  
5 pc(s)
The Mini MP3 Module is a small, low-cost mp3 module with a simplified audio output that can be connected directly to a speaker or an earphone jack. The module can be used as a stand-alone module with attached battery, speaker, and push buttons or used in combination with a microcontroller or...
− +
Mini Lock-style Solenoid - 6VDC
$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Lock-style Solenoid - 12VDC
$5.00  
8 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
Out-of-stock
Looking for a battery powered liquid pump for your Micro:Bit project? This submersible Mini Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with...
Out-of-stock
Mini HDMI to HDMI Cable - 1.5 meter
$7.99  
3 pc(s)
Connect an HDMI device with a mini HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1.5 meter long This cable works with Raspberry Pi Zero W. Dimensions: 1.5 meter Long
− +
Mini Breadboard - Yellow
$1.75  
13 pc(s)
This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! Perfect for tiny projects and for sticking onto the top of Arduino...
− +
Mini Breadboard - White
$1.75  
10 pc(s)
This white Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be...
− +
Mini Breadboard - Red
$1.75  
17 pc(s)
This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! Perfect for tiny projects and for sticking onto the top of Arduino...
− +
Mini Breadboard - Green
$1.75  
18 pc(s)
This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! Perfect for tiny projects and for sticking onto the top of Arduino...
− +
Mini Breadboard - Blue
$1.75  
12 pc(s)
This blue Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! Perfect for tiny projects and for sticking onto the top of Arduino...
− +
Mini Breadboard - Black
$1.75  
14 pc(s)
This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! Perfect for tiny projects and for sticking onto the top of Arduino...
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Yellow
$2.95  
7 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Red
$2.95  
9 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Green
$2.95  
3 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
Mini 3-Wire Volt Meter (0 - 99.9VDC) - Blue
$2.95  
9 pc(s)
Put a voltage meter anywhere with this very handy display. These are often used by RC hobbyists for keeping track of batteries but we thought it would be great on a breadboard or enclosure. This is the 3-wire version of the volt meter, two wires are used to power it and the third wire is used...
− +
-20%
Mifare 13.56MHz RC522 RFID Card Reader (3.3V Supply)
$6.35 $7.95  
5 pc(s)
MFRC522 is the highly integrated RFID card reader which works on non-contact 13.56MHz communication. Designed by NXP as a low power consumption, low cost and compact size read and write chip, this MFRC522 is the best choice in the development of portable hand-held devices. It supports...
− +
microSD USB Reader
$3.50  
5 pc(s)
This is an awesome little microSD USB reader. Just slide your microSD card into the inside of the USB connector, then stick this into a USB port and the card's contents will pop up on your computer. Very sneaky - we love it! This little guy is great for pulling data logs off microSD media. This...
− +
-20%
microSD Shield
$19.60 $24.50  
1 pc(s)
Running out of memory space in your Arduino project? The SparkFun microSD Shield equips your Arduino with mass-storage capability, so you can use it for data-logging or other related projects. Communication with microSD cards is achieved over an SPI interface. The SCK, DI, and DO pins of the...
− +
MicroSD Card Adapter
$0.20  
33 pc(s)
The micro SD card adapter looks like a regular-sized SD card with a slot in it for the microSD card. It allows you to transfer data between your device and a computer.
− +
-30%
microSD Card - 64GB (Class 10, UHS-I )
$14.00 $20.00  
9 pc(s)
This is a class 10 64GB microSD memory card, perfect for housing operating systems for single board computers and a multitude of other information. Since this is a class 10 UHS-I microSD it is capable of transferring data at speeds up to 100MB/s allowing it to have a noticeable increase in...
− +
-50%
micro:Gamepad
$13.50 $27.00  
10 pc(s)
Micro:bit gamepad is an expansion gamepad based on micro:bit. You only need to plug in the micro:bit, it will turn into a wireless remote controller a wireless game console. This product packaged with acrylic plate, that giving it a good feel and no longer feels like a bare circuit...
− +
micro:bit Flex Sensor
$32.50  
4 pc(s)
This micro:bit Flex Sensor is specifically designed for micro:bit to detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. This sensors are easy to use. It will vary its resistance depending on how much it...
− +
micro:bit EduFun Mini Project Kit - Temperature and Humidity Sensor (I2C)
$15.00  
13 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...
− +
micro:bit EduFun Mini Project Kit - Mini Thermal Printer
$95.00  
1 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...
− +
micro:bit EduFun Mini Project Kit - LED Matrix Module
$25.00  
Out-of-stock
SGBotic has created a series of micro:bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...
Out-of-stock
micro:bit EduFun Mini Project Kit - DS18B20 Waterproof Temperature Sensor
$16.00  
2 pc(s)
SGBotic has created a series of micro:bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakCode blocks package to remove the complexity of using these devices, making it easier for inventors to...
− +
micro:bit EduFun Mini Project Kit - Automated Plant Watering System
$21.00  
3 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...
− +
Micro Servo - 9g (360° Full Rotation)
$5.90  
Out-of-stock
Here is a simple, low-cost, high quality continuous 360° full-rotation servo motor for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as...
Out-of-stock
Micro Servo - 9g
$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....
− +
Micro Metal Gearmotor Bracket Extended Pair
$6.90  
4 pc(s)
This compact bracket enables convenient mounting of popular, Sanyo-style miniature metal gearmotors. The plastic bracket encloses the otherwise exposed gears, and the mounting tabs capture the nuts for easy installation. This version has mounting tabs that allow for use with the Pololu Wheel...
− +
Micro Metal Gearmotor 50:1
$19.90  
3 pc(s)
This micro metal gearmotor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Wheel 42x19mm and Wheel 32x7mm . The brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch), or you can use the mounting bracket or...
− +
Micro HDMI to HDMI Cable - 3 meter
$15.99  
12 pc(s)
Connect an HDMI device with a micro HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 3 meter long. Dimensions: 3 meter Long
− +
MI:power board for the BBC micro:bit
$9.50  
3 pc(s)
When assembled, the MI:power board is connected directly to the 3V, GND and P0 connections on the micro:bit. The 3V and GND connections provide power to the micro:bit and the built in buzzer is connected to P0, which is the default output pin when using the audio functions in the Block Editor...
− +
Metal Bracket for Ø25mm Gearmotor
$4.50  
1 pc(s)
This aluminum gearmotor brackets let you securely mount 25D mm metal gearmotors to your project. Each bracket includes two M3 screws for securing the motor to the bracket.
− +
-20%
MEMS Microphone Breakout - INMP401 (ADMP401)
$12.80 $16.00  
1 pc(s)
This tiny breakout board features the ADMP401 MEMs microphone. One of the key advantages to this breakout and microphone is the bottom ported input. This means the microphone's input can fit flush against the enclosure of your project. Plus you will not have to deal with trying to solder the...
− +
-30%
Membrane 4x4 Matrix Keypad
$1.65 $2.35  
5 pc(s)
This 16-button keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 8 microcontroller pins...
− +
-30%
Membrane 3x4 Matrix Keypad
$1.65 $2.35  
3 pc(s)
This 12-button keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 7 microcontroller pins...
− +
Mega Enclosure - Clear
$3.50  
1 pc(s)
The Arduino Mega 2560 R3 is a very big and powerful microcontroller,needless to say, you want to keep it protected. Why not protect it with one of these snazzy plastic enclosures? These cases protect the Arduino Mega 2560 from things like rogue wires that might short it out while still allowing...
− +
Medium Breadboard White, 400 Tie-In Points
$2.95  
1 pc(s)
This is your tried and true white solderless breadboard. It has 2 power buses, 30 columns, and 10 rows - a total of 400 tie in points. All pins are spaced by a standard 0.1". The two sets of five rows are separated by about 0.3", perfect for straddling a DIP package over. The board accepts...
− +
Mecanum Wheels For TT Gear Motor - 80mm Diameter (PAIR)
$15.50  
1 pc(s)
Mecanum wheels allow your robot to not only travel forward and backward, but also sideways! Nine rollers set on a 45° rotational axis parallel to the main rotational axis of the wheel enable a broad a range of movement. Rotating all four wheels in the same direction causes forward or backward...
− +
MCP3008 - 8-Channel 10-Bit ADC With SPI Interface
$4.50  
5 pc(s)
The MCP3008 has a 8-Channel 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply...
− +
MCP3002 - 2-Channel 10-Bit ADC With SPI Interface
$3.50  
39 pc(s)
The MCP3002 has a 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply 2 Channels...
− +
MAX6675 Temperature Sensor Kit with K-Type Thermocouple
$9.99  
3 pc(s)
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. This MAX6675 breakout board does everything for you, and can be easily interfaced with Arduino, micro:bit, Raspberry Pi and any other microcontroller via 12-bit resolution SPI bus. A...
− +
Male Crimp Pins for 0.1" Housings 20-Pack
$2.80  
6 pc(s)
These pins can be crimped on 22-28AWG wires and snapped into our crimp connector housings to create custom cables that are compatible with standard 0.1"-pitch headers and solderless breadboards. These male pins are sold in packs of 20.
− +
MakerBeamXL - 500mm Clear Anodised (Threaded)
$9.90  
28 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
9 - 17