Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11 12 13 14
8 - 17
Oldest Items First
48 Per Page
-29%
12mm Panel Mount Momentary Pushbutton - Green
$0.60 $0.85  
6 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including leads) is 24mm and has small solder lugs for connection. Mounting hole diameter is 12mm Documents : Datasheet
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Red)
$0.60 $0.75  
5 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1A@250VAC. Overall length (including...
− +
-20%
Panel Mount Pushbutton - Latching (12mm, Green)
$0.60 $0.75  
38 pc(s)
This is the basic SPDT panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 3A@125VAC / 1.5A@250VAC. Overall length (including...
− +
-33%
Panel Mount Pushbutton - Latching (10mm, Red)
$0.50 $0.75  
28 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
2 x 75A 60V Brushless DC Motor Controller (HBL2360A)
Contact us for details

 
 
Roboteq 's HBL2360A is a high-current, dual channel controller for hall-sensor equipped Brushless DC motors. The controller uses the position information from the sensors to sequence power on the motors' 3 windings in order to generate smooth continuous rotation. The controller also uses...
Panel Mount Pushbutton - Latching (10mm, Green)
$0.50  
35 pc(s)
This is the basic panel-mount latching on/off switch. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. These buttons are rated up to 1A@250VAC. Overall length (including leads) is 32mm and...
− +
-29%
7mm Panel Mount Momentary Pushbutton - Red
$0.60 $0.85  
19 pc(s)
This is the basic SPST normally-open panel-mount momentary button. These buttons are rated up to 0.5A@125VAC. Overall length (including leads) is 27.5mm and has small solder lugs for connection. Mounting hole diameter is 7mm Documents : Datasheet
− +
2 Way Spring Clamp Terminal Block (Pack of 3)
$0.95  
16 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
-30%
3 Way Spring Clamp Terminal Block (Pack of 3)
$0.95 $1.35  
126 pc(s)
This terminal block is a spring clamp electrical connector where the individual stripped conductors are clamped down to the metal part by means of a spring. Compare to screw-type terminal block, this Spring Clamp Terminal Block gives you a constant connection. It always exerts the same force on...
− +
-10%
Big Easy Stepper Motor Driver
$31.50 $35.00  
1 pc(s)
The Big Easy Driver, designed by Brian Schmalz , is a stepper motor driver board for bi-polar stepper motors up to 2A/phase. It is based on the Allegro A4983 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
Adafruit 16-Channel 12-bit PWM/Servo Driver - I2C interface - PCA9685
$33.85  
1 pc(s)
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you...
− +
HDMI to VGA Video Adapter w/Audio and USB Power Out (Metal Case)
$9.95  
1 pc(s)
This nifty adapter cable with durable metal casing converts the digital HDMI video signals which are outputted from Raspberry Pi, into an analog signal required by the widely used VGA monitor. This adapter has an audio jack that provides stereo headphone/line out (HDMI 1.3 cables carry both...
− +
-8%
LilyPad Arduino 328 Main Board
$22.95 $24.95  
1 pc(s)
The LilyPad Arduino 328 Main Board is an Arduino-programmed microcontroller designed to be easily integrated into e-textiles and wearable projects. It offers the same functionality you find in other Arduino boards, in a lightweight, round package designed to minimize snagging and profile,...
− +
MakerBeam NEMA 17 Bracket For Stepper Motor
$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.
− +
-20%
LilyPad LED White (5pcs)
$4.75 $5.95  
Out-of-stock
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively...
Out-of-stock
-20%
3.5" Resistive Touchscreen LCD + Pre-configured 16GB microSD Card For RaspberryPi
$37.60 $47.00  
7 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 3.5 inches 480x320 high resolution LCD display with resistive touchscreen, engineered specifically to let you quickly attached the...
− +
-20%
Resistor Kit - 1/4W 1% (600 total)
$6.40 $8.00  
9 pc(s)
Don't you hate it when you're in the middle of a build and you don't have a certain value of resistor? Don't let it happen again with this resistor kit. This kit contains a resistor color code chart and 20 each of 30 standard value 1/4 Watts resistors with 1% tolerance. It's perfect for starting...
− +
USB mini-B Cable - 30cm
$2.50  
4 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 30cm
− +
USB mini-B Cable - 50cm
$3.00  
3 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 50cm
− +
USB microB Cable - 25cm
$2.50  
1 pc(s)
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
− +
USB microB Cable - 50cm
$3.00  
Out-of-stock
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
Out-of-stock
USB Cable A to B - 50cm
$3.00  
Out-of-stock
This is the classic. It's an A to B Male/Male type peripheral cable for printers and other large peripheral devices. Compatible with Arduino Uno and Arduino Mega. Dimensions: 50cm
Out-of-stock
-50%
Thermally Conductive Adhesive
$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...
− +
ESP8266 Wifi Module SMD
$8.90  
4 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...
− +
Flex Cable for Raspberry Pi Camera - 30cm
$3.50  
11 pc(s)
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 30cm long. Each order comes with one cable, Pi Camera...
− +
Flex Cable for Raspberry Pi Camera - 50cm
$3.95  
1 pc(s)
This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 50cm long. Each order comes with one cable, Pi Camera...
− +
-20%
MP3 Trigger
$60.00 $75.00  
1 pc(s)
Make some noise with your next project! The MP3 Trigger board is built to make it MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control,...
− +
Mini Real Time Clock Module (DS3231) for Raspberry Pi
$11.95  
5 pc(s)
Unlike most computers, the Pi lacks a Real-Time Clock (RTC). This means the Pi doesn't know what time it is when powered on. While your Pi is connected to a network it will be able to set it's clock correctly using NTP ( Network Time Protocol ) server. Without a network connection your Pi...
− +
Toy DC Motor Bracket - Metal
$0.20  
9 pc(s)
This compact metal bracket enables convenient mounting of our popular Toy DC Motors . ‎Ø2mm mounting holes. Note: Toy DC motor not included.
− +
Toy DC Motor Bracket - Plastic
$1.50  
13 pc(s)
This compact plastic bracket enables convenient mounting of our popular Toy DC Motors . Note: Toy DC motor not included. Documents : Dimension drawing
− +
9V Battery Snap - Heavy Duty
$0.80  
50 pc(s)
9V snap connector wth hard shell that is built stronger to last longer. Comes with color-coded wire leads. Great for replacements or projects. Length: ~ 15cm
− +
Type 2 NFC Silicone Adjustable Wristband (NTAG213) - Yellow
$3.50  
1 pc(s)
This is a blank NFC Type 2 silicone wristbands with adjustable fitting - often used for parties/events or identification but also found in other systems where a small proximity card is desired. This wristbands contains a NTAG213 RFID chip with 144 bytes of memory and an antenna, and is...
− +
3-Blade Nylon Boat Propeller - 40mm Diameter
$2.50  
11 pc(s)
Small fiber reinforced nylon propeller for boat, 3 blades and 40mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø40 x 18.5mm Center bore：1.9 mm
− +
Micro HDMI to HDMI Cable - 3 meter
$15.99  
12 pc(s)
Connect an HDMI device with a micro HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 3 meter long. Dimensions: 3 meter Long
− +
3-Blade Boat Propeller - 27mm Diameter (5 pcs)
$0.50  
7 pc(s)
Small propeller for boat, 3 blades and 27mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø27 x 6.9mm Center bore：1.9 mm
− +
Mini HDMI to HDMI Cable - 1.5 meter
$7.99  
3 pc(s)
Connect an HDMI device with a mini HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1.5 meter long This cable works with Raspberry Pi Zero W. Dimensions: 1.5 meter Long
− +
Ultrasonic Range Finder - HRXL-MaxSonar-WR
$195.00  
2 pc(s)
This outdoor sensor provides very short to long distance detection and ranging in a compact, robust PVC housing. The ultrasonic sensor meets the IP67 water intrusion standard and matches standard electrical ¾-inch PVC pipe fittings. High output acoustic power combined with continuously...
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +
Copper Tape - Conductive Adhesive, 5mm (20 Meters)
$4.95  
10 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
Translucent Silicone Tubing 7mm ID x 9mm OD - 1 meter
$4.50  
39 pc(s)
This soft, flexible tubing is specially sourced for our Diaphragm Liquid Pump and mini liquid pump . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. No tubing clamp is...
− +
Copper Tape - Conductive Adhesive, 50mm (20 Meters)
$29.95  
5 pc(s)
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
− +
DELink 2 USB Link For Kangaroo PID Motion Controller
$35.00  
4 pc(s)
The DELink 2 USB Link is the perfect compliment to our Kangaroo x2 self-tuning PID motion controller. Coupled with the DEScribe software, you can upload / download settings or reset the Kangaroo to factory defaults. Utilizing the easy-to-use USB bus, changing the settings on your Kangaroo...
− +
-50%
3DR Buzzer for PX4 / Pixhawk
$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm
− +
-55%
3DR Safety Switch for PX4 / Pixhawk
$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - Green
$1.95  
1 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - White
$1.95  
3 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
Protoboard, Double-Sided Pad-per-Hole, 4x6cm - Blue
$1.95  
2 pc(s)
The prototyping circuit board has a general purpose double sided pad-per-hole pattern which is good for general purpose analog and digital use. 0.95mm holes are drilled on 2.54mm centers. Size: 4 x 6cm, 1.6mm thick
− +
1 2 3 4 5 6 7 8 9 10 11 12 13 14
8 - 17

Recently Viewed