Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11 12 13 14
8 - 17
Sort by Price: High to Low
48 Per Page
600mm MakerBeam Clear Anodised (Threaded)
$9.50  
30 pc(s)
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
− +
Capacitive Touch Breakout - AT42QT1011
$9.50  
2 pc(s)
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1011 SparkFun Capacitive Touch Breakout offers a single, momentary capacitive touch button with easy-to-use digital I/O pins. The AT42QT1011 is a dedicated,...
− +
Pan/Tilt Bracket
$9.50  
1 pc(s)
This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. This pan/tilt bracket works with our small servo motor . Documents: Dimensional Drawing Assembly Guide
− +
2-CH IR Remote Relay Controller (Soldering Kit)
$9.50  
5 pc(s)
This fun little soldering kit enables you to make a 2-channel infra-red remote relay controller. The kit features a microcontroller that takes command from an infra-red receiver and controls 2 relays individually. Using an infra-red keypad, you will be able to turn on/off the relays....
− +
Cap Nuts M3 (50 pcs)
$9.50  
1 pc(s)
Cap nuts come in packages of 50 pieces. They will give your MakerBeam project an extra finish.
− +
MI:power board for the BBC micro:bit
$9.50  
3 pc(s)
When assembled, the MI:power board is connected directly to the 3V, GND and P0 connections on the micro:bit. The 3V and GND connections provide power to the micro:bit and the built in buzzer is connected to P0, which is the default output pin when using the audio functions in the Block Editor...
− +
ESP8266 Wifi Module SMD
$8.90  
4 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...
− +
Kitronik Edge Connector Breakout Board for BBC micro:bit
$8.90  
9 pc(s)
Looking to do more with your BBC micro:bit? Unlock its potential with this pre-built version of our Edge Connector Breakout Board! This breakout board has been designed to offer an easy way to connect additional circuits and hardware to the pins on the edge of the BBC micro:bit. It provides...
− +
Mono 2.5W Class D Audio Amplifier - PAM8302
$8.50  
1 pc(s)
This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω...
− +
-7%
RF Link Receiver - 4800bps (434MHz)
$8.50 $9.10  
2 pc(s)
These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
Timing Belt - 2GT (Length 852mm)
$8.50  
1 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 852mm,...
− +
Heating Pad - 5x15cm
$8.20  
1 pc(s)
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro...
− +
-36%
Quad-band Cellular Duck Antenna SMA
$8.00 $12.55  
2 pc(s)
This is a small, high-quality, quad-band, regular SMA terminated, cellular antenna. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS : 1850 to 1990MHz Documents: GSM Antenna 850-1900MHz
− +
Mini HDMI to HDMI Cable - 1.5 meter
$7.99  
3 pc(s)
Connect an HDMI device with a mini HDMI port to one with a regular size HDMI port together with this basic HDMI cable. It has nice molded grips for easy installation, and is 1.5 meter long This cable works with Raspberry Pi Zero W. Dimensions: 1.5 meter Long
− +
-20%
WiFi Module - ESP8266 1MB Flash
$7.95 $9.95  
56 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...
− +
Mini USB Microphone
$7.95  
2 pc(s)
This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with any computer, laptop, SBC, etc! Works great with a Raspberry Pi computer, but you can also use it with any other computer you want to record audio on. Simply plug it right in and...
− +
TT Gear Motor All-Metal Gearbox - 1:90 Gear Ratio
$7.95  
12 pc(s)
These TT All-Metal Gear Motors are a low cost and reliable way to get your projects moving. They look a lot like our yellow all-plastic gear motors but these have all of the motor gears machined from steel, so they won't strip as easily, and they're twice as slow (and twice as powerful) given...
− +
-20%
Servo - Generic Metal Gear (Micro Size)
$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...
− +
Brass Sponge Solder Tip Cleaner
$7.95  
2 pc(s)
This is a brass sponge that will help clean your soldering iron tip. Use it to remove residue from your iron tip before soldering. It cleans better than conventional sponges and will not damage your iron tip. Made of low abrasive brass shavings, requires no water and won't cool down the tip.
− +
16x2 Character LCD 5V (w/Soldered Header)
$7.95  
18 pc(s)
This is a basic 16 character by 2 line display. White text on Blue background . Utilizes the extremely common HD44780 parallel interface chipset ( datasheet ). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Pin headers...
− +
HC-SR04 Ultrasonic Sensor - I2C
$7.95  
15 pc(s)
This is the latest version of the popular HC-SR04 Low Cost Ultrasonic Sensor. Instead of the common GPIO interface, this version of HC-SR04 uses I2C to communicate with host controller. HC-SR04 ultrasonic sensor provides a very low-cost and easy method of distance measurement. It...
− +
-20%
Load Cell - 1kg, Straight Bar
$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Cell - 10kg, Straight Bar
$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 2kg, Straight Bar
$7.90 $9.90  
20 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 2kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Cell - 20kg, Straight Bar
$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
Digital PWM Motor Speed Controller - 5A
$7.90  
2 pc(s)
This DC motor controller allows you to control both the speed and direction of a DC motor without sacrificing torque. It can provides up to a maximum continuous current of 5A to your DC motor or other DC load using a Pulse Width Modulated (PWM) with a Duty cycle fully adjustable from 10%-100%....
− +
MakerBeam Servo Bracket
$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. Documents: Mechanical drawing
− +
-20%
Load Cell - 5kg, Straight Bar
$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock
Through-Beam Infrared Sensor Kit - 30cm
$7.90  
8 pc(s)
This Through-Beam Infrared Sensor Kit consists of two separate components: an Infrared transmitter and detector. They work by having an transmitter side that sends out a beam of human-invisible infrared light, then a detector across the way which is sensitive to that same light. When an...
− +
ESP8266 WiFi Module Programmer - USB Interface
$7.90  
6 pc(s)
This module is a USB programmer for ESP8266 Wifi Module . The module is hard wired to automatically enter into download mode once the programmer is plugged into the USB port, there is no need to press any button on the programmer or wifi module. It is very convenient for users to download...
− +
Heating Pad - 5x10cm
$7.90  
12 pc(s)
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro...
− +
Breadboarding Wire Bundle - M/M
$7.90  
8 pc(s)
65 flexible stranded core wires with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Total 65 wires in a mix of colors 49 100mm 8 x 150mm 4 x 200mm 4 x 250mm
− +
MakerBeam NEMA 17 Bracket For Stepper Motor
$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.
− +
Standard Metal Gear Micro Servo
$7.90  
2 pc(s)
This is a low-cost micro size, high quality metal gear servo for all your mechatronic needs. The servo comes with a standard 3 pin power / control cable, and mounting hardware. You can use any servo code, hardware, or library to control these servos. Good for beginners who want to make stuff...
− +
-20%
Load Sensor - 50kg
$7.90 $9.90  
12 pc(s)
This load cell / sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. Each straight bar load cell is made from an aluminum-alloy and is capable of measure up to about 50kg. Documents : Specifications Load Sensor Tutorial (NerdKits)
− +
MakerBeam M3 Hex Nut Driver
$7.50  
3 pc(s)
This high quality hex nut driver (5,5mm) is a standard item in our MakerBeam Starter Kit. Work with both standard nuts and Cap nuts.
− +
Wind Power Kit (Partially Assembled)
$7.45  
7 pc(s)
This Wind Power Kit is designed to show students how alternative energy is created by harnessing the power produced by the wind. The kit has a high efficient generator that can produce useful electricity at low speed. It can generate sufficient electricity to light up a LED by blowing onto the...
− +
-20%
RF Link Receiver - 4800bps (315MHz)
$7.25 $9.10  
6 pc(s)
These wireless receivers work with our 315MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...
− +
-30%
Basic 8x2 Character LCD - Black on Green 5V
$7.00 $9.95  
3 pc(s)
This is a basic 8 character by 2 line display with black text on green background. The screen utilizes the extremely common HD44780 parallel interface chipset. Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Includes LED backlight....
− +
-30%
Type-K Thermocouple probe - 150mm
$6.99 $10.00  
10 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 150mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-36%
Type-K Thermocouple probe - 200mm
$6.99 $11.00  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 200mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
Pulse Oximeter & Heart-Rate Sensor - MAX30102
$6.99  
4 pc(s)
MAX30102 Sensor is an integrated pulse oximetry and heart-rate monitor module. It is equipped with a red and IR LEDs as well as a very sensitive photon detector. The idea is to pulse the different LEDs, then detect what shines back. Based on the reflected signature it's possible to measure...
− +
-7%
Type-K Thermocouple probe - 50mm
$6.99 $7.50  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 50mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-22%
Type-K Thermocouple probe - 100mm
$6.99 $9.00  
7 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 100mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
Outdoor Type 2 NFC Tag - NTAG213 (Diameter 52mm)
$6.95  
5 pc(s)
This disc-shaped, waterproof tag contains a small NTAG213 RFID chip and an antenna, and is passively powered by the reader/writer when placed a couple centimeter away.. The housing will withstand rugged conditions and is designed for outdoor use. It can be secured with screws. You can use...
− +
Wind Power Kit (Soldering Kit)
$6.95  
5 pc(s)
This Wind Power Kit is designed to show students how alternative energy is created by harnessing the power produced by the wind. The kit has a high efficient generator that can produce useful electricity at low speed. It can generate sufficient electricity to light up a LED by blowing onto the...
− +
Copper Tape - Conductive Adhesive, 10mm (20 Meters)
$6.90  
Out-of-stock
Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making. Copper tape is even used to join things together using solder, like the stained glass on Tiffany lamps. This copper tape is backed by a...
Out-of-stock
Micro Metal Gearmotor Bracket Extended Pair
$6.90  
4 pc(s)
This compact bracket enables convenient mounting of popular, Sanyo-style miniature metal gearmotors. The plastic bracket encloses the otherwise exposed gears, and the mounting tabs capture the nuts for easy installation. This version has mounting tabs that allow for use with the Pololu Wheel...
− +
1 2 3 4 5 6 7 8 9 10 11 12 13 14
8 - 17

Recently Viewed