Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11 12 13
7 - 17
Sort by Price: Low to High
48 Per Page
-20%
RFID Tag - 125kHz
$2.35 $2.95  
19 pc(s)
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic RFID tag works in the 125kHz RF range and comes with a unique 40-bit ID. It is not re-programmable. This blank, smooth, and mildly...
− +
ESP8266 WiFi Module Breakout Board
$2.40  
30 pc(s)
This ESP8266 WiFi Module Breakout Board allows you to take the dual row header of the ESP-01 and make it breadboard friendly. This board comes with the header and decoupling capacitor presoldered, but requires you to solder on the male pins. NOTE : ESP8266 WiFi Module not included.
− +
25mm Delrin Plastic Ball Bearings For Jetbot
$2.45  
35 pc(s)
Delrin ball bearings are made of a composite material well-suited for low- to moderate-load applications. This 25mm ball bearings is specially sourced for the Nvidia Jetbot. Dimensions: 25mm diameter
− +
WS2812 RGB LED Stick
$2.50  
1 pc(s)
This is the WS2812 Addressable RGB LED Stick with eight LEDs. The WS2812 is a addressable smart RGB LED that uses a single data line to control brightness and color. The embedded constant-currnet driver keeps the LED brightness consistent even if the input voltage varies. There are...
− +
9V Battery Holder with On/Off Switch, 3-Pin JST
$2.50  
5 pc(s)
Enclosed battery holder for 9V battery. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
Photo Interrupter Module (Straight)
$2.50  
6 pc(s)
This Photo Interrupter Module is widely used in motor speed detection, pulse count, the position limit, etc. It will trigger a signal when light between the sensor's gap is blocked. It works with 3.3V to 5VDC, and gives a HIGH on DO pin when the beam is blocked, and a LOW output when...
− +
-37%
Jumper Wire Kit
$2.50 $3.95  
1 pc(s)
This is a time saving kit of jumper wires - cut, stripped, and pre-bent for your prototyping pleasure. Included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each.
− +
DC Barrel Jack Adapter - Male
$2.50  
36 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution.
− +
-31%
In-line power switch for 2.1mm barrel jack
$2.50 $3.60  
10 pc(s)
Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an...
− +
Photo Interrupter Module (T-Shape)
$2.50  
5 pc(s)
This Photo Interrupter Module is widely used in motor speed detection, pulse count, the position limit, etc. It will trigger a signal when light between the sensor's gap is blocked. It works with 3.3V to 5VDC, and gives a HIGH on DO pin when the beam is blocked, and a LOW output when...
− +
-31%
Illuminated Capacitive Switch Module - Blue
$2.50 $3.60  
2 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
Break Away Female Headers - Swiss Machine Pin
$2.50  
15 pc(s)
Single row of 40-holes, female header with swiss round machined pins. These units have very high quality round pins to accept and retain machine pin headers much better. Can be cut to size with a pair of wire-cutters. Standard 2.54mm spacing. Documents: 40-Pin Swiss Female...
− +
DC Barrel Jack Adapter - Female
$2.50  
4 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might be the simple solution.
− +
-31%
Illuminated Capacitive Switch Module - Red
$2.50 $3.60  
1 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
USB mini-B Cable - 30cm
$2.50  
4 pc(s)
This is the standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your USB Hubs, FTDI Breakout Board and USB Lipo charger w/Mini B connector, among other things. Dimensions: 30cm
− +
Rotary Encoder Breakout
$2.50  
Out-of-stock
The rotary encoder is a rotary input device that provides an indication of how much and in which direction the encoder has been turned. This 20-pulse Rotary Encoder Breakout has a nice 'clicking' feel and also has a push-button built into it so you can press onto the knob to close a separate...
Out-of-stock
3-Blade Nylon Boat Propeller - 40mm Diameter
$2.50  
11 pc(s)
Small fiber reinforced nylon propeller for boat, 3 blades and 40mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø40 x 18.5mm Center bore：1.9 mm
− +
Water Sensor - Large
$2.50  
2 pc(s)
This water sensor is designed to detect water, which can be used to sense water level and leakage. It works by using exposed copper traces to detect the presence of water droplets. The sensor board has a sensing area of 47 x 36mm. The on-board potentiometer is used to set the threshold for...
− +
4 x AA Battery Holder with Cover and Switch
$2.50  
3 pc(s)
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-50%
SSOP to DIP Adapter 8-Pin
$2.50 $5.00  
6 pc(s)
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm)....
− +
USB microB Cable - 25cm
$2.50  
1 pc(s)
USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell phones and portable media devices. Connector shape may vary slightly from image as our stock...
− +
Timing Pulley - Shaft Mount (20T, 5mm Bore)
$2.50  
3 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 20 teeth with a gear pitch of 2mm, an outer diameter of 16mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 20...
− +
Basic LED Soldering Kit
$2.50  
1 pc(s)
This fun little soldering kit is designed for beginners to practise their soldering skill. The kit features a pair of large LEDs which will light up when power is applied. Assembly is easy, and you should be able to do it in 10-15 minutes. The kit comes with: a construction...
− +
-31%
Illuminated Capacitive Switch Module - Yellow
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
Orange and Clear Wheel for Bi-axial Gearbox Motor - 70mm Diameter
$2.50  
10 pc(s)
Need a wheel for your Bi-axial Gear Motor ? This Orange & Clear TT Motor Wheel is equipped with a nice, thick silicone tread and a press-fit design to make connecting super quick and easy. Make cute robots today with a couple of these orange wheels! Note : This wheel is only...
− +
USB Cable A to B - 30cm
$2.50  
1 pc(s)
This is the classic. It's an A to B Male/Male type peripheral cable for printers and other large peripheral devices. Compatible with Arduino Uno and Arduino Mega. Dimensions: 30cm
− +
-31%
Illuminated Capacitive Switch Module - Green
$2.50 $3.60  
8 pc(s)
This Illuminated Capacitive Switch Module feature an innovative method of combining the benefits of capacitive switching with colour back lighting. The backlit switching solution allows makers to prototype and evaluate HMI designs without the need to develop custom capacitive sensors and back...
− +
-20%
Solder Leaded - 15-gram Tube
$2.55 $3.20  
1 pc(s)
This is your basic tube of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 15 grams (around 5ft). Easy to solder with - recommended for beginners. Mix: 63% Sn / 37% Pb
− +
-50%
IOIO and Breadboard Holder
$2.60 $5.20  
1 pc(s)
This holder allows you to safely secure a IOIO development board and a self-adhesive breadboard in place to easily run jumper wires in between the two to form simple or complex prototyping circuits. Unlike it’s cousin, for the Arduino, this IOIO and breadboard holder has been made specifically...
− +
Voltage Regulator - 3.3V
$2.75  
20 pc(s)
This is the basic LD1117V33 voltage regulator, a low drop positive regulator with a 3.3V fixed output voltage. This fixed regulator provides a great amount of stability and protection for your project and with its on chip trimming this regulator is able to reach an output voltage tolerance...
− +
4 x AA Battery Holder with On/Off Switch, 3-Pin JST
$2.80  
5 pc(s)
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
9V Battery Holder with Switch & Barrel Jack
$2.80  
Out-of-stock
This is a 9V battery pack with on/off switch and terminated with a standard 5.5x2.1mm, center-positive barrel jack. Use this to battery-power your Arduino or other electronic projects. Battery & screw not included. Dimensions : 68mm x 33mm x 21mm Lead length: 12cm...
Out-of-stock
Female Crimp Pins for 0.1" Housings 20-Pack
$2.80  
13 pc(s)
These pins can be crimped on 22-28AWG wires and snapped into our crimp connector housings to create custom cables that are compatible with standard 0.1"-pitch headers and solderless breadboards. These female pins are sold in packs of 20.
− +
WS2812 RGB LED Stick (w/Male Pin Header)
$2.80  
12 pc(s)
This is the WS2812 Addressable RGB LED Stick with eight LEDs. The WS2812 is a addressable smart RGB LED that uses a single data line to control brightness and colour. The embedded constant-current driver keeps the LED brightness consistent even if the input voltage varies. There are...
− +
Male Crimp Pins for 0.1" Housings 20-Pack
$2.80  
6 pc(s)
These pins can be crimped on 22-28AWG wires and snapped into our crimp connector housings to create custom cables that are compatible with standard 0.1"-pitch headers and solderless breadboards. These male pins are sold in packs of 20.
− +
-5%
Type 2 NFC Card - NTAG216
$2.85 $3.00  
53 pc(s)
A white plastic PVC card that has an NTAG216 chip embedded inside. About the size of a credit card, this is a blank white NFC card that you can use with a card printer to customize. It houses an NTAG216 chip which holds up to 888 bytes of memory. Documents : Datasheet (NTAG216)...
− +
-50%
Standard LCD 16x2 - White on Blue 5V
$2.90 $5.80  
403 pc(s)
This is a standard 16 character by 2 line display. White text on Blue background. Utilizes the extremely common HD44780 parallel interface chipset ( datasheet ). Interface code is freely available. You will need ~11 general I/O pins to interface to this LCD screen. Features :...
− +
Passive Piezo Buzzer w/Leads -13mm
$2.90  
3 pc(s)
This is a small 13mm round passive buzzer that operates around the audible 4kHz range. We drove it directly from a 3v to 5V Arduino or micro:bit to generate simple melody. The buzzer leads are terminated with male pin. Note : This passive buzzer requires a square wave (PWM) signal to...
− +
Piezo Element
$2.90  
2 pc(s)
Piezo elements come in handy when you need to detect vibration or a knock. You can use these for tap or knock sensors pretty easily by reading the voltage on the output. They can also be used for a very small audio transducer such as a buzzer. Documents: Datasheet...
− +
6 x AA Battery Holder with Switch and Cover
$2.90  
15 pc(s)
Enclosed battery holder for six AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...
− +
-21%
3 Buttons Membrane Keypad
$2.90 $3.65  
23 pc(s)
This 3 Buttons Membrane Keypad provides a useful human interface component for microcontroller projects. It's made of a thin, flexible membrane material with an adhesive backing so you can attach it to nearly anything. The keys are connected into a matrix, it only take up 4 I/O pins of the...
− +
-25%
Raspberry Pi GPIO Tall Header - 2x20
$2.90 $3.85  
22 pc(s)
This 2x20 "tall" header has the same number and spacing of pins as a Raspberry Pi and provides your board with the ability to extend the heights of your GPIO to accommodate for enclosures or other parts that can encapsulate your Pi. This through-hole header has 40 0.1"-spaced pins and can...
− +
3-Pin Cable for Sharp Distance Sensors / SRF01 (w/Male Pin Header)
$2.90  
13 pc(s)
This 30cm cable has 26 AWG wires and a 3-pin female JST PH-style connector that works with Sharp Infra-red distance sensors: GP2Y0A02YK , GP2Y0A21YK and GP2Y0A41SK0F . The other ends of the wires are terminated with male pin header. The wire color scheme matches the Sharp distance sensor...
− +
Temperature Sensor - TMP36
$2.90  
375 pc(s)
The TMP36 are low voltage, precision centigrade temperature sensors. They provide a voltage output that is linearly proportional to the Celsius (centigrade) temperature. The TMP36 do not require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the −40°C...
− +
Mini Submersible Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
4 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This Mini Submersible Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with tubing....
− +
T5577 RFID Tag - Read/Write 125kHz
$2.95  
8 pc(s)
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic T5577 RFID tag works in the 125kHz RF range and supports read/write operation. Note : This is a blank tag - its ID must be chosen and...
− +
Wheel for 5V Stepper Motor - 60mm Diameter
$2.95  
4 pc(s)
This wheel is designed specifically for our 5V stepper motor It comes with a rubber tread, and a press-fit design to make connecting super quick and easy. Note: Wheel only. Stepper motor not included. Wheel body: 56 x 8mm
− +
ESP8266 WiFi Module Breakout Board - Assembled
$2.95  
2 pc(s)
This ESP8266 WiFi Module Breakout Board allows you to take the dual row header of the ESP-01 and make it breadboard friendly. This board is fully assembled. NOTE : ESP8266 WiFi Module not included.
− +
1 2 3 4 5 6 7 8 9 10 11 12 13
7 - 17