Delivery fee

New items

1 2 3 4 5 6 7 8 9 10
4 - 18
Sort by Price: High to Low
24 Per Page
SWADJHV High Voltage Step Down Adjustable Switching Regulator
$42.50  
4 pc(s)
The SWADJHV is the a high-voltage edition of our popular DE-SWADJ adjustable switching reulators. It is designed to accept an input voltage ranging from 5-60V, allowing you to power a variety of applications from extremely high-voltage sources. The SWADJHV is pin-compatible with the common 78XX...
− +
DE-SWADJ3 Step Down Adjustable Switching Regulator 25W
$42.00  
6 pc(s)
The DE-SWADJ 3 is a larger version of our DE-SWADJ adjustable step down voltage regulator. Previously it was necessary to put multiple DE-SWADJ units in parallel to achieve ratings over 1A, which was bulky, expensive and carried with it a considerable increase in dropout voltage. The...
− +
Dual MAX14870 Motor Driver for Raspberry Pi
$42.00  
4 pc(s)
This motor driver expansion board and its corresponding Python library make it easy to control a pair of bidirectional, brushed DC motors with a compatible Raspberry Pi (Model B+ or newer), including the Pi 3 Model B+ and Model A+. The expansion board features two MAX14870 H-bridge motor...
− +
Miniature Capacitive Fingerprint Sensor
$39.95  
1 pc(s)
Secure your project with biometrics - this all-in-one Capacitive Fingerprint Sensor will make adding fingerprint detection and verification super simple. Similar to the capacitive touchscreen, this captive fingerprint sensor measures your finger by using human conductivity, creating an...
− +
-20%
RedBot - Robotic Development Platform
$39.95 $49.95  
6 pc(s)
The RedBot Mainboard is a robotic development platform that works with the Arduino IDE. The RedBot is a motor driver and Ardiuno combination with various headers and connections, eliminating the need to stack multiple shields. By using the RedBot accessory boards and your own chassis, you...
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +
-11%
Arduino Uno Rev 3 ( A000066 )
$39.95 $45.00  
3 pc(s)
This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf...
− +
-20%
Raspberry Pi Infrared-Sensitive Camera w/Adjustable Focus Lens
$39.00 $48.75  
6 pc(s)
The Raspberry Pi Infrared-Sensitive Camera Module is a custom designed add-on for Raspberry Pi that does not have an 'IR cut filter' installed. Similar to the regular Pi camera, it attaches to Raspberry Pi by way of one of the two small sockets on the board upper surface. This interface uses...
− +
-15%
CAN-BUS Shield
$38.25 $45.00  
1 pc(s)
The CAN-BUS Shield provides your Arduino or Redboard with CAN-BUS capabilities and allows you to hack your vehicle. This shield allows you to poll the ECU for information including coolant temperature, throttle position, vehicle speed, and engine rpms. You can also store this data or output...
− +
DC & Stepper Motor HAT for Raspberry Pi
$38.00  
Out-of-stock
Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, this HAT uses...
Out-of-stock
Flexiforce Pressure Sensor - 25lbs
$38.00  
4 pc(s)
This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but the resistance does not change while being flexed. Resistance changes only when...
− +
Flexiforce Pressure Sensor - 1lb
$38.00  
1 pc(s)
This is a piezoresistive force sensor. The harder you press, the lower the sensor's resistance. Pressing hard, the resistance changes from infinite to ~300k. The sensor itself is thin and flexible, but the resistance does not change while being flexed. Resistance changes only when...
− +
-20%
3.5" Resistive Touchscreen LCD + Pre-configured 16GB microSD Card For RaspberryPi
$37.60 $47.00  
7 pc(s)
The Raspberry Pi Display Module Kit is designed to provide a quick and easy interface to Raspberry Pi without any wiring hassles. It features a fully assembled 3.5 inches 480x320 high resolution LCD display with resistive touchscreen, engineered specifically to let you quickly attached the...
− +
-8%
SparkFun Sunny Buddy - MPPT Solar Charger
$37.50 $40.55  
1 pc(s)
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar charger provide you with the ability to get the most possible power out of your solar panel or other photovoltaic device and into a rechargable LiPo battery. Set-up is...
− +
vRTCam - Remote Controller w/Wifi Video - Wide Angle Lens
$37.50  
8 pc(s)
Looking for a device that allows you to control your robot and at the same time to see what the robot sees on your mobile phone? Look no further than this vRTCam from SGBotic. The vRTCam is designed for use with a mobile phone as remote controller with minimum setup. It is unique in a...
− +
Adafruit DC Motor + Stepper FeatherWing Add-on
$36.75  
7 pc(s)
This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). It features a fully-dedicated PWM driver chip that handles all the motor and speed controls over I2C. Since the FeatherWing only...
− +
Negatron DC-DC Converter
$36.50  
4 pc(s)
Negatron is a buck-boost converter that takes a positive voltage and turns it into a negative voltage that you can use with amplifier circuits and more. The output is adjustable from -1.3V to -12V. Negatron is also able to step up/step down the magnitude of the voltage. For example,...
− +
Cool White LED Flexi-Strip - 5V (Bare, 5 meters)
$36.00  
3 pc(s)
These single color LED strip feature 60 ultra bright cool white LEDs on one meter. As these are bare LED strips that have no protective coating, your project won't be water proof but there is access to each LED and each strip length can be easily modified. Each of these strips need a 3V to 5V...
− +
-25%
LiPower Shield
$36.00 $48.00  
2 pc(s)
Is there anything an Arduino can't do? Well, for one, most of them can't be powered directly from a 3.7V LiPo battery; much less charge and monitor that battery. The SparkFun LiPower Shield takes care of this by combining the functionality of two of our favorite battery power boards: the...
− +
-20%
Raspberry Pi Zero Mini Camera - 160 Degree 60mm
$36.00 $45.00  
5 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
-20%
Raspberry Pi Zero Mini Camera - 72 Degree 150mm
$36.00 $45.00  
5 pc(s)
This teeny-weeny Camera Board is the perfect companion to the popular Raspberry Pi Zero! The sensor is 5MP, and the components are mounted on the flexible circuit board. As such, a little care is needed when handling, just like the connector on the Pi Zero. It's a great camera in a tiny...
− +
3.3V, 2.5A Step-Down Voltage Regulator D24V25F3
$35.00  
10 pc(s)
This D24V25F3 synchronous buck voltage regulator takes an input voltage of up to 38 V and efficiently reduces it to 3.3 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.5 A and features reverse voltage protection. Typical efficiencies of 80%...
− +
DELink 2 USB Link For Kangaroo PID Motion Controller
$35.00  
4 pc(s)
The DELink 2 USB Link is the perfect compliment to our Kangaroo x2 self-tuning PID motion controller. Coupled with the DEScribe software, you can upload / download settings or reset the Kangaroo to factory defaults. Utilizing the easy-to-use USB bus, changing the settings on your Kangaroo...
− +
Feather M0 Adalogger
$34.95  
2 pc(s)
Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 Adalogger - an 'all-in-one' Cortex M0 datalogger (or data-reader)...
− +
1 2 3 4 5 6 7 8 9 10
4 - 18