Delivery fee

New items

$1.00 $1.85  
19 pc(s)
This 1xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable sliding cover and an ON/OFF switch which can be used to control power to your project. The leads are about 150mm, and the last 5mm of them are tinned. Dimensions: 69 x 26...

$1.00  
26 pc(s)
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a yellow lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA. Pack of 10 diffused yellow LEDs....

$1.00  
27 pc(s)
We know this looks like a lot of our other LEDs, but it's not! This is a PTH Addressable RGB LED with a WS2812 control IC built right into the LED. This PTH version is incredibly similar to its SMD cousin, except it is breadboard friendly and a lot simpler to solder into your project and is...

$1.00  
85 pc(s)
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a green lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA. Pack of 10 diffused green LEDs....

$1.00 $1.35  
11 pc(s)
10K thermistor with a negative temperature coefficient. Good choice for temp-sensing aplications. Vishay part #: NTCLE100E3103JB0 Note: You get only one thermistor. Document: Datasheet

$1.00  
9 pc(s)
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic 5mm LED with a green lens. It has a typical forward voltage of 2.0V and a rated forward current of 20mA. Pack of 10 diffused red LEDs....

$1.05 $1.50  
84 pc(s)
Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 2.54mm spacing so it plugs very...

$1.20 $1.35  
3 pc(s)
The Educational Traffic Light Module is a low cost hardware module designed to allow users to take their first steps into interfacing microcontroller with the real world. It is designed to remove many of the common hurdles people are faced with when getting started using hardware with the...

$1.20 $1.50  
36 pc(s)
This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino Uno (among a number of other products) allowing you to easily make your project...

$1.20  
39 pc(s)
The Nylon Ball Caster has the capbility to support maximum 10kg payload. The Caster is strong and lightweight. It has 20mm high round body, with a total weight of only 25g. Documents : Dimension drawing

$1.20  
8 pc(s)
The LDR Sensor Module is used to detect the presence of light / measuring the intensity of light. The output of the module goes LOW in the presence of light and it becomes HIGH in the absence of light. Features: Voltage: 3.3V~5V Analog output Dimensions: 21 x...

$1.20  
89 pc(s)
This is a very simple, clear infrared LED. These devices operate between 940-950nm and work well for generic IR systems including remote control and touch-less object sensing. Pair them with any of our IR receivers (see Related Items below). 1.5VDC forward voltage and 50mA max forward...