Delivery fee

New items

1 2 3 4 5 6 7 8 9 10 11 12 13
7 - 21
$3.50  
6 pc(s)
These are 12" long jumper wires terminated as female to female. Use these to jumper from any male header on any board. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one package of ten jumpers (colors shown). We use these wires for everything! They work great...

$25.50  
4 pc(s)
The Pololu step-up/step-down voltage regulator S7V7F5 is a switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC converter) that uses a buck-boost topology. It takes an input voltage from 2.7 V to 11.8 V and increases or decreases the voltage to a fixed 5 V output...

$11.60 $14.50  
1 pc(s)
These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. Features : Stride Angle (degrees) : 7.5 2-Phase Rated Voltage : 12V Rated Current : 400mA 3mm Diameter Drive Shaft...

$5.90  
5 pc(s)
This is you basic tube of unleaded (Pb-free) solder with a 60/40 no clean, water soluble resin core. 0.031" gauge and 15 grams. Mix: 96.5% tin / 3.0% silver / 0.5% copper

$0.95  
2 pc(s)
These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. All lenses are clear. Features: Standard size - T1 3/4 5mm 6,000mcd brightness 3.2V forward drop Forward current 20mA Documents:...

$2.50  
3 pc(s)
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$19.70  
1 pc(s)
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the...

$8.50 $9.10  
2 pc(s)
These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...

$1.75  
10 pc(s)
This white Mini Breadboard is a great way to prototype your small projects! With 170 tie points there's just enough room to build and test simple circuits; They're also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be...

$15.75 $17.00  
5 pc(s)
The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at...

$3.50  
139 pc(s)
This Rainbow Wire provides a convenient way to connect the signals in your projects. You can always pull the rainbow wires off to make individual jumpers, or keep them together to make neatly organized wire harnesses. The color-coding can be used to organize power, ground and other signal types...

$6.50  
4 pc(s)
This is a simple, thumbnail-size RFID tag. These tags are great for sensing presence, identification, etc., and they're small, so they can be easily sewn into clothing or inserted into enclosures. Each tag comes with a unique 32-bit ID code and is not reprogrammable. The carrier frequency of...
1 2 3 4 5 6 7 8 9 10 11 12 13
7 - 21