Delivery fee

New items

$3.90  
3 pc(s)
Thermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. The Thermal Tape listed below works very...

$1.00 $1.35  
11 pc(s)
10K thermistor with a negative temperature coefficient. Good choice for temp-sensing aplications. Vishay part #: NTCLE100E3103JB0 Note: You get only one thermistor. Document: Datasheet

$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...

$6.00 $7.50  
3 pc(s)
Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don't. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin. Documents: Datasheet Wiring Example...

$9.90  
5 pc(s)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a...

$12.90  
7 pc(s)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a...

$2.90  
375 pc(s)
The TMP36 are low voltage, precision centigrade temperature sensors. They provide a voltage output that is linearly proportional to the Celsius (centigrade) temperature. The TMP36 do not require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the −40°C...

$12.45 $24.90  
12 pc(s)
The SmartMatrix Shield is the best way to connect the Teensy 3.2 to Large RGB LED matrix display panels . The shield makes it easy to connect the 13 signals required to drive the display, connects an external 5V supply to power the display and Teensy, and brings out the Teensy's free...

$42.90  
4 pc(s)
Teensy 4.0 is the latest Teensy, offering the fastest microcontroller and powerful peripherals in the Teensy 1.4 by 0.7 inch form factor. It features an ARM Cortex-M7 processor at 600MHz, with a NXP iMXRT1062 chip, the fastest microcontroller available today. Teensy 4.0 is the same size and...

$6.50 $9.10  
19 pc(s)
These tactile buttons are great for all sorts of projects. This assortment comes with 2 of each of 6 different colors for a total of 12 buttons. The colored caps are removable and the buttons fit into breadboards. See the drawing below for exact dimensions. Documents: Drawing

$2.95  
8 pc(s)
RFID is useful for sensing and identifying tagged people and objects for access control, automation, and a whole range of different applications. This basic T5577 RFID tag works in the 125kHz RF range and supports read/write operation. Note : This is a blank tag - its ID must be chosen and...

$17.50  
8 pc(s)
The MakerBeamXL T-slot nut is made of stainless steel and was specially designed to slide into the T-slot grooves of the MakerBeamXL profile. The T-slot nut is great to fasten brackets or corner cubes.