Delivery fee

New items

1 - 11
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
13 - 27
Sort by Popularity
12 Per Page
Screw Terminals 3.5mm Pitch (2-Pin)
$0.50  
1 pc(s)
Screw Terminals with 3.5mm pitch pins. Comes in 2 or 3 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 125V @ 6A. Terminal can accept 30 to 20AWG wire. 3.5mm/138mil pin pitch will not fit standard...
− +
USB-ISS - Enhanced USB-I2C Module
$45.00  
Out-of-stock
The USB-ISS Multifunction USB Communications Module provides a complete interface between your PC and the I2C bus, SPI bus, a Serial port and general purpose Analogue Input or Digital I/O. The module is powered from the USB. Operating voltage is selectable between 3.3V and 5V and...
Out-of-stock
DRV8825 Stepper Motor Driver Carrier, High Current
$26.95  
7 pc(s)
The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section...
− +
Analog/Digital MUX Breakout
$9.95  
3 pc(s)
This is a breakout board for the very handy 16-Channel Analog/Digital Mulitplexer/Demultiplexer CD74HC4067. This chip can be used to connect 16 analog sources (like sensors) to 5 pins on a microcontroller. 4 of the pins must be digital pins, 1 pin must be an analog to digital conversion pin....
− +
DE-SWADJ Step Down Adjustable Switching Regulator - 10W
$24.50  
2 pc(s)
The DE-SWADJ is the adjustable version of our SW0XX step down voltage regulators. It is designed to be the easiest possible way to add an adjustable voltage source to a new or existing project with all the efficiency benefits of switch-mode power. The DE-SWADJ is pin-compatible with the...
− +
Breakout Board for USB miniB
$3.95  
2 pc(s)
This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a miniUSB/USB miniB connector to your breadboard - here it is. Also good for an un-regulated, non-limited 5V supply up to 100mA.
− +
Pololu Dual VNH5019 Motor Driver Shield for Arduino
$126.00  
3 pc(s)
This motor driver shield and its corresponding Arduino library make it easy to control two bidirectional, high-power, brushed DC motors with an Arduino or Arduino clone. The board features a pair of robust VNH5019 motor drivers from ST, which operate from 5.5 to 24 V and can deliver a...
− +
DE-SWADJ3 Step Down Adjustable Switching Regulator 25W
$42.00  
6 pc(s)
The DE-SWADJ 3 is a larger version of our DE-SWADJ adjustable step down voltage regulator. Previously it was necessary to put multiple DE-SWADJ units in parallel to achieve ratings over 1A, which was bulky, expensive and carried with it a considerable increase in dropout voltage. The...
− +
Alligator Test Leads (Pack of 10) - Medium
$5.50  
8 pc(s)
Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them,...
− +
-33%
Screw Terminals 5mm Pitch (2-Pin)
$0.50 $0.75  
53 pc(s)
Screw Terminals with 5mm pitch pins. Comes in 2 positions and have the really cool feature of slide-locking together to form any size you need (4, 6, up to 20 without problems). Rated up to 300V @ 8A. Terminal can accept 26 to 14AWG wire. 5mm/197mil pin pitch will line up well with standard...
− +
-20%
Sparkfun XBee Wireless Shield
$19.95 $24.95  
1 pc(s)
Xbee radios are an awesome way to add wireless capability to your Arduino project and now it's even easier with the XBee Shield. The shield form-factor mates directly with any dev board that has an Arduino standard footprint and equips it with wireless communication capabilities using the...
− +
-50%
LilyPad Protoboard Large
$4.75 $9.50  
1 pc(s)
This is a large board for prototyping through hole components with the LilyPad system. There are an array of pins all shorted together with 10mil traces. This allows for quick and easy prototyping - all you have to do is cut the traces between holes you don't want connected! Standard 0.1"...
− +
1 - 11
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
13 - 27

Recently Viewed