Wireless

$5.50  
26 pc(s)
2.4GHz/5GHz Duck Antenna with regular RP-SMA RF connector and IPEX interface cable for connecting to our dual mode wireless module . Includes: 1x Antenna 1x IPEX Interface cable Features: Type: Omni-Directional Frequency: 2400~2500MHz/5150~5850MHz Gain: 3dBi...

$3.00  
2 pc(s)
This dual band Flexible Printed Circuit (FPC) WiFi antenna covers the WLAN bands of 2.4 - 2.5 GHz and 5.15 – 5.85 GHz. It has a 120mm cable assembly with a standard IPEX connector for ease of connection to the board. With this small form factor the antenna is perfect internal options for WiFi...

$8.90  
2 pc(s)
This adhesive, omni-directional antenna is perfect for situations when you're trying to get a signal out from a transmitter that you've jammed down into an enclosure. Operating on the 2.4GHz band, it works great for WiFi, Bluetooth or ZigBee. Just connect the antenna using the attached u.fl...

$9.60  
8 pc(s)
2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long. The FCC is moving towards Part 15 compliance. All this means is that all the SMA RF connectors are changing gender. Really annoying for those...

$13.50  
3 pc(s)
Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. This antenna mates nicely with the Reverse Polarized SMA Connector. Documents: Datasheet Dimensions: 0.5x7.7"

$1.40  
398 pc(s)
This is a 10-pin socket with 2mm pitch that mates with the popular XBee radio from Maxstream. Use this small part to avoid having to solder your precious radio to a PCB. You'll need two of these sockets to connect to all 20 pins on the XBee. Sold in single unit.

$1.00  
44 pc(s)
This spring coil antenna is designed for the 433MHz devices. Each antenna is constructed of phosphor copper. Features: Frequency Range(MHz):433MHz +/-5MHz Gain(dBi):2.15 V.S.W.R:≤1.5@433M Input Impedance( OHM):50 Spring outer diameter: Wire diameter is 0.6mm,...

$18.50  
7 pc(s)
This 434Mhz Wireless Transceiver Module is a new-generation multi-channel RF transceiver operating at the sub-GHz ISM bands from 433.4-473.0MHz,. The module supports up to 100 channels, with selectable RF power transmitter and highly sensitive RF receiver. Its output power level ranges from...

$1.00  
45 pc(s)
This spring coil antenna is designed for the 868 / 915MHz devices. Each antenna is constructed of copper. Features: Frequency Range(MHz):868 / 915MHz Gain(dBi):2 dBi V.S.W.R:≤2 Input Impedance( OHM):50 Spring outer diameter: 5mm Total length: 16mm...

$16.90  
2 pc(s)
This Antenna Kit is meant for use with the LoPy , SiPy . But it's good for any 800MHz and 900MHz radio. Includes: External antenna. Interface Cable SMA to U.FL NOTE : Using the LoRa/Sigfox radio without the external antenna can lead to damage of the device and is...

$34.50  
2 pc(s)
Another unique shield for the Arduino platform! This XBee shield allows the Arduino USB board to establish wireless communication with other devices. Just slip this shield onto two Arduino board and you've got a wireless network. Or you can put the Xbee into command mode and group them...

$16.00  
28 pc(s)
This is a handy little USB Bluetooth 4.0 dongle. Utilising the CSR8510 chipset, this dongle is backwards compatible with v2.1 and earlier, but also supports the latest v4.0 low energy bluetooth transmission. It has a maximum distance of up to 50m and includes an indicator LED. Use this Dongle...

$16.00  
Out-of-stock
This Bluetooth Low Energy 4.0 Module utilizes a HM-10 module to provide your Arduino with an easy to use wireless link between your Arduino and any compatible iOS or Android (4.3+) device. It works by simulating a UART device beneath the surface, sending data back and forth between the...
Out-of-stock

$55.00  
1 pc(s)
This is a simple breakout for the Roving Networks Bluetooth module. All pertinent pins are broken out and labeled. This new version's headers are unpopulated. Check below for appropriate headers. The module from Roving Networks is powerful, small, and very easy to use. This Bluetooth...

$4.00  
Out-of-stock
This is a simple breakout board for the popular XBee product from Maxstream. This board breakouts out all 20 pins of the XBee to a 0.1" standard spacing dual row header. The spacing between 0.1" headers is 0.5" making it breadboard DIP friendly. We high recommend using the female sockets to...
Out-of-stock

$110.55  
9 pc(s)
The cellular module connects your Arduino or Raspberry Pi to the internet using the 3G mobile network. Just connect this CEL02 3G Cellular Module to your controller, insert a SIM card from an operator offering 3G coverage and start controlling your world through the internet. The module...

$34.80  
1 pc(s)
This is a dual mode wireless module applicable for Jetson Nano. It supports 2.4GHz / 5GHz dual band WiFi and Bluetooth 4.2. N OTE: This module requires external antenna kit . Features : Chip: Intel 8265AC Bands: 2.4GHz / 5GHz Speed: 300Mbps / 867Mbps WiFi...

$19.95  
5 pc(s)
The ESP32 Development Board is a low-footprint, minimal system development board powered by ESP-WROOM-32 module. The ESP-WROOM-32 is a powerful and compact module that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...

$15.95  
5 pc(s)
The ESP32 Development Board Lite is a compact version of standard ESP32 development board. Like other ESP32 boards, it has a 32-bit dual core microcontroller that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...

$23.50  
30 pc(s)
The ESP32 Development Board is a low-footprint, minimal system development board powered by ESP-WROOM-32 module. The ESP-WROOM-32 is a powerful and compact module that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet connectivity. This...

$4.90  
5 pc(s)
This ESP8266 WiFi Module Adapter allows easy interfacing of ESP8266 WiFi Module to Arduino Uno / Mega or any development board running on 5V logic. It features onboard LDO regulator to supply 3V to ESP8266 WiFi Module and logic level converter for both Tx and Rx pins. Note :...

$2.90  
30 pc(s)
This ESP8266 WiFi Module Breakout Board allows you to take the dual row header of the ESP-01 and make it breadboard friendly. This board comes with the header and decoupling capacitor presoldered, but requires you to solder on the male pins. NOTE : ESP8266 WiFi Module not included.

$3.40  
5 pc(s)
This ESP8266 WiFi Module Breakout Board allows you to take the dual row header of the ESP-01 and make it breadboard friendly. This board is fully assembled. NOTE : ESP8266 WiFi Module not included.

$8.90  
10 pc(s)
This module is a USB programmer for ESP8266 Wifi Module . The module is hard wired to automatically enter into download mode once the programmer is plugged into the USB port, there is no need to press any button on the programmer or wifi module. It is very convenient for users to download...

$9.90  
15 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...

$21.95  
Out-of-stock
The ESP32 DevKitC from Espressif is a low-footprint, minimal system development board powered by Espressif ESP-WROOM-32 module. The ESP-WROOM-32 is a powerful and compact module that combines Wi-Fi and Bluetooth to support a wide range of applications that require wireless and internet...
Out-of-stock

$16.00  
7 pc(s)
The HC-05 is a class 2 Bluetooth module designed for transparent wireless serial communication. It is pre-configured as a slave Bluetooth device. Once it is paired to a master Bluetooth device such as PC, smart phones and tablet, its operation becomes transparent to the user. All data...

$15.00  
40 pc(s)
The HC-06 is a class 2 slave Bluetooth module designed for transparent wireless serial communication. Once it is paired to a master Bluetooth device such as PC, smart phones and tablet, its operation becomes transparent to the user. All data received through the serial input is immediately...

$8.00  
5 pc(s)
This connector cable interfaces UFL RF connectors to RP-SMA antennas. Use it to attach any standard RP-SMA 2.4GHz antenna to the DPAC 802.11 modules. Dimensions: 4" Length

$5.90  
22 pc(s)
This is a 4" connector cable that interfaces U.FL RF connectors to regular SMA antennas (not RP-SMA!). Documents: Datasheet

$16.50  
30 pc(s)
NodeMcu is an open source IoT platform based on the ESP-12 module. The board is pre-loaded with LUA firmware that enable you to prototype your IoT product within a few Lua script lines. You can also program it using Arduino IDE. This development kit includes a CP2102 TTL to USB chip for...

$12.00  
2 pc(s)
This is a high gain, 9" antenna is perfect for AVL applications where cellular reception is a must. Connector is regular SMA so don't confuse it with 2.4GHz antennas. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS : 1850...

$11.20  
2 pc(s)
This is a small, high-quality, quad-band, regular SMA terminated, cellular antenna. Specifications: GSM/850E : 824 to 894MHz GSM : 880 to 960MHz DCS : 1710 to 1880MHz PCS : 1850 to 1990MHz Documents: GSM Antenna 850-1900MHz

$7.90  
6 pc(s)
These wireless receivers work with our 315MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...

$7.90  
5 pc(s)
These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...

$6.90  
5 pc(s)
These wireless receivers work with our 315MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...

$6.90  
2 pc(s)
These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a very simple wireless data link. Since these are only transmitters, they will only work communicating data one-way, you would need two pairs (of...

$14.90  
Out-of-stock
The Serial To WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The onboard ESP-12F ESP8266 module is capable of either hosting an application or offloading all Wi-Fi networking functions from another...
Out-of-stock

$14.90  
Out-of-stock
The Serial To WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The onboard ESP-12F ESP8266 module is capable of either hosting an application or offloading all Wi-Fi networking functions from another...
Out-of-stock

$25.00  
1 pc(s)
Xbee radios are an awesome way to add wireless capability to your Arduino project and now it's even easier with the XBee Shield. The shield form-factor mates directly with any dev board that has an Arduino standard footprint and equips it with wireless communication capabilities using the...

$48.80  
2 pc(s)
This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. Each ANT500 is constructed of stainless steel and features an SMA male connector, rotating shaft, and adjustable elbow. The ANT500 is a 50...

$26.50  
3 pc(s)
This nRF2401A module has the same minimum interface of 7 pins (all in a .1" spaced connector) as the original nRF2401A module, but the size is reduce by over 60%! These are the nRF2401A 2.4GHz transceiver modules with built in chip antenna designed around the Nordic Semiconductor nRF2401A...

$24.00  
1 pc(s)
This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature - very nice! Please...

$6.50  
3 pc(s)
This module based on Nordic nRF24L01+, a highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesiser and baseband logic including the Enhanced...

$19.90  
3 pc(s)
This module based on Nordic nRF24L01+, a highly integrated, ultra low power (ULP) 2Mbps RF transceiver for the 2.4GHz ISM (Industrial, Scientific and Medical) band. Nordic nRF24L01+ integrates a complete 2.4GHz RF transceiver, RF synthesiser and baseband logic including the Enhanced...

$25.50  
18 pc(s)
This wifi module is a miniature USB wireless adapter with massive antenna that supports greater range and speed. It is fully complies with wireless 802.11b/g/n standards with data rate up to 300 Mbps when connecting with wireless 802.11n device. This Wifi module works well with the...

$9.90  
13 pc(s)
The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network. The ESP8266 is capable of either hosting an application or offloading all Wi-Fi networking functions from another application processor. Each...

$21.50  
11 pc(s)
Make your Internet of Things device cable-free by adding WiFi. Take advantage of the Raspberry Pi USB port to add a low cost, but high-reliability wireless link. This wifi module is a miniature USB wireless adapter with massive antenna that supports greater range and speed. It is fully complies...

$106.25  
3 pc(s)
This is a breakout board for the RN-131G WiFly GSX module, an ultra-low power 802.11b/g transceiver. This board breaks out all pins of the RN-131G to two 17-pin 0.1" pitch headers. Board comes fully assembled and tested as pictured. We've revised the board by adding some LED indicators and...

$43.25  
Out-of-stock
This is the XBee XB24CZ7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between...
Out-of-stock

$39.90  
1 pc(s)
This is the XBee Explorer Dongle unit for the Digi XBee module line. With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee. No cables needed! This unit works with all XBee modules including the Series 1...

$15.95  
1 pc(s)
The XBee Explorer Regulated takes care of the 3.3V regulation, signal conditioning, and basic activity indicators (Power, RSSI and DIN/DOUT activity LEDs). It translates the 5V Rx signals to 3.3V so that you can connect a 5V (down to 3.3V) system to any XBee module (Note: This board does not...

$32.50  
1 pc(s)
This is a simple to use, RS232 to serial base unit for the XBee line. This unit works with all XBee modules including the Series 1 and Series 2, standard and Pro version. Plug the unit into the XBee Explorer, attach a RS232 cable, and you will have direct access to the serial and programming...

$39.90  
1 pc(s)
This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and...

$39.90  
19 pc(s)
This is the very popular 2.4GHz XBee XBP24-AWI-001 module from Digi. The Pro series have the same pinout and command set of the basic series with an increase output power of 60mW! These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command...

$32.00  
1 pc(s)
The DFRobot Xbee USB adapter is used for the XBee module configuration parameters to facilitate or to use as a wireless data transmission. It can be easily connected to a PC via mini USB cable. Further, it has XBee-setting support software X-CTU. It can also be used as a USB-TTL adapter....