Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Sensors

Accelerometers
Barometric / Pressure
Biometrics
Capacitive / Inductive
Compass / Magneto
Current
Flex / Force
Gas
GPS
Gyros
Infra-red
IMU
LiDAR
Light / Colour
Liquid / Flow
Motion
Sound
Temperature / Humidity
Ultrasonic
1 2
Sort by Price: Low to High
96 Per Page
Infra-red Phototransistor 940nm
$0.99  
28 pc(s)
This is a very simple, clear infrared phototransistor. These devices operate between 940-950nm and work well with our infrared LED . Phototransistors are similar to photoresistors (or LDR) but produce both current and voltage, while photoresistors only produce current....
− +
Mini Photocell (LDR - Light Dependent Resistor)
$1.00  
68 pc(s)
This is a very small photocell. A photocell changes (also called a photodetector , CdS or photoconductive cell) resistance depending on the amount of light it is exposed to. These little sensors make great ambient light triggers (when light in the room turns on, do something)....
− +
-26%
Thermistor 10K
$1.00 $1.35  
11 pc(s)
10K thermistor with a negative temperature coefficient. Good choice for temp-sensing aplications. Vishay part #: NTCLE100E3103JB0 Note: You get only one thermistor. Document: Datasheet
− +
Infra-red LED 950nm - 5mm (10 pcs)
$1.20  
89 pc(s)
This is a very simple, clear infrared LED. These devices operate between 940-950nm and work well for generic IR systems including remote control and touch-less object sensing. Pair them with any of our IR receivers (see Related Items below). 1.5VDC forward voltage and 50mA max forward...
− +
Photocell Light Sensor Module (Analog Output)
$1.20  
8 pc(s)
The LDR Sensor Module is used to detect the presence of light / measuring the intensity of light. The output of the module goes LOW in the presence of light and it becomes HIGH in the absence of light. Features: Voltage: 3.3V~5V Analog output Dimensions: 21 x...
− +
Hall Effect Sensor (Latching)
$1.50  
Out-of-stock
The US1881 is an integrated Hall effect latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A...
Out-of-stock
Hall-Effect Sensor (Non-Latching)
$1.50  
Out-of-stock
The AH1815 is an integrated Hall-Effect non-latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size....
Out-of-stock
Infrared Remote Control (21 Buttons)
$1.50  
10 pc(s)
Have you ever needed a cheap way to activate something from across the room? Infrared remotes are still the cheapest way to wirelessly control a device. This 21 buttons remote controller works with TSOP38238 infrared receiver which have an operating voltage from 2.5V - 5.5V. Includes :...
− +
Screw Nut Set for HC-SR04 Ultrasonic Sensor
$1.65  
21 pc(s)
This screw / bolt set is specially sourced for HC-SR04 Ultrasonic sensor. Each set consists 4 pieces of screws, nuts and washer. Screw length: 10mm
− +
Infrared Remote Control Kit
$1.90  
6 pc(s)
Have you ever needed a cheap way to activate something from across the room? Infrared remotes are still the cheapest way to wirelessly control a device. The IR remote in this kit offers buttons for four directions, select and basic number keys. It is ideal for implementing an IR remote control...
− +
Flame Sensor Module
$1.90  
2 pc(s)
This Flame Sensor Module is sensitive to infra-red wavelength between 760 nm to 1100 nm that is emitted from fire flame. The module has 2 outputs: Analogue, which gives a real-time voltage output signal on thermal resistance, and Digital which allows temperature thresholds to be set via a...
− +
Infrared Obstacle Avoidance Sensor
$1.95  
10 pc(s)
The Infrared Obstacle Avoidance Sensor has a pair of infrared transmitting and receiving sensors. The infrared LED emits Infrared signals at certain frequency and when an obstacle appears on the line of infrared light, it is reflected back by the obstacle which is sensed by the receiver....
− +
HC-SR04 Ultrasonic Sensor Adaptor
$1.95  
23 pc(s)
This is a simple adaptor to provide an easy way to mount a HC-SR04 Ultrasonic Sensor to our 2WD Robot Chassis Kit . Fully assembled, no soldering is required. Notes: Copper standoff, nuts and screws are available separately.
− +
Line Follower Sensor
$1.99  
6 pc(s)
The Line Follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. It can detect transitions from light to dark (lines) or even objects directly in front of it. The sensor has an...
− +
Line Follower Sensor (Adjustable)
$1.99  
Out-of-stock
The Line Follower sensor gives your robot the ability to detect lines or nearby objects. The sensor works by detecting reflected light coming from its own infrared LED. It can detect transitions from light to dark (lines) or even objects directly in front of it. The sensor has an...
Out-of-stock
Water Sensor - Small
$2.10  
4 pc(s)
This Water Sensor is designed for water detection, which can be used in sensing the water level and leakage. This sensor works by having a series of exposed copper traces which will turn on the transistor when water droplets shot the copper traces. This sensor works with the digital I/O...
− +
-31%
Tilt Sensor
$2.20 $3.20  
12 pc(s)
This basic tilt switch can easily be used to detect orientation. Inside the can are a pair of balls that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors,...
− +
Photo Interrupter GP1A57HRJ00F Breakout Board
$2.35  
4 pc(s)
A simple breakout PCB for the GP1A57HR photo interrupter. This PCB has three connections for PWR, GND, and Signal. When the gate is clear, SIG will be high (>4.9V). When the gate is blocked by a finger, writing utensil, food pellet, or anything else - SIG will go low (<0.4V)....
− +
Photo Interrupter Module (Straight)
$2.50  
6 pc(s)
This Photo Interrupter Module is widely used in motor speed detection, pulse count, the position limit, etc. It will trigger a signal when light between the sensor's gap is blocked. It works with 3.3V to 5VDC, and gives a HIGH on DO pin when the beam is blocked, and a LOW output when...
− +
Water Sensor - Large
$2.50  
2 pc(s)
This water sensor is designed to detect water, which can be used to sense water level and leakage. It works by using exposed copper traces to detect the presence of water droplets. The sensor board has a sensing area of 47 x 36mm. The on-board potentiometer is used to set the threshold for...
− +
Photo Interrupter Module (T-Shape)
$2.50  
5 pc(s)
This Photo Interrupter Module is widely used in motor speed detection, pulse count, the position limit, etc. It will trigger a signal when light between the sensor's gap is blocked. It works with 3.3V to 5VDC, and gives a HIGH on DO pin when the beam is blocked, and a LOW output when...
− +
3-Pin Cable for Sharp Distance Sensors / SRF01 (w/Male Pin Header)
$2.90  
13 pc(s)
This 30cm cable has 26 AWG wires and a 3-pin female JST PH-style connector that works with Sharp Infra-red distance sensors: GP2Y0A02YK , GP2Y0A21YK and GP2Y0A41SK0F . The other ends of the wires are terminated with male pin header. The wire color scheme matches the Sharp distance sensor...
− +
3-Pin Cable for Sharp Distance Sensors / SRF01
$2.90  
Out-of-stock
This 30cm cable has 26 AWG wires and a 3-pin female JST PH-style connector that works with Sharp Infra-red distance sensors: GP2Y0A02YK , GP2Y0A21YK and GP2Y0A41SK0F . The other ends of the wires are unterminated; they can be cut to length to match your application. The wire color scheme...
Out-of-stock
Temperature Sensor - TMP36
$2.90  
375 pc(s)
The TMP36 are low voltage, precision centigrade temperature sensors. They provide a voltage output that is linearly proportional to the Celsius (centigrade) temperature. The TMP36 do not require any external calibration to provide typical accuracies of ±1°C at +25°C and ±2°C over the −40°C...
− +
Piezo Element
$2.90  
2 pc(s)
Piezo elements come in handy when you need to detect vibration or a knock. You can use these for tap or knock sensors pretty easily by reading the voltage on the output. They can also be used for a very small audio transducer such as a buzzer. Documents: Datasheet...
− +
Infrared Receiver Diode (TSOP38238)
$3.00  
33 pc(s)
Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes. The TSOP38238 is a miniaturized receiver for infrared remote control...
− +
HC-SR04 Low Cost Ultrasonic Module (5V Supply)
$3.45  
15 pc(s)
HC-SR04 ultrasonic sensor provides a very low-cost and easy method of distance measurement. This sensor measures distance using sonar. An ultrasonic (well above human hearing) pulse is transmitted from the unit and distance-to-target is determined by measuring the time required for the...
− +
Soil Moisture Sensor
$3.50  
10 pc(s)
This soil moisture sensor can read the amount of moisture present in the soil surrounding it. It's a low tech sensor, but ideal for monitoring an urban garden, or your pet plant's water level. This is a must have tool for a connected garden! This sensor uses the two probes to pass...
− +
M5Stack Module - Light
$3.50  
9 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Light Module uses photo cell to measure light intensity. The resistance of the photo cell depending on the amount of light it is...
− +
HC-SR04 v2 - Low Cost Ultrasonic Sensor (3V to 5V Supply)
$3.95  
1 pc(s)
This product is the second generation of the popular HC-SR04 Low Cost Ultrasonic Sensor. Unlike the first generation HC-SR04 that can only operate between 4.8V to 5V DC, this new version has much wider input voltage range, allow it to work with controller operates on 3.3V. HC-SR04...
− +
-28%
Photo Interrupter GP1A57HRJ00F
$4.00 $5.55  
3 pc(s)
This sensor is composed of an infrared emitter on one upright and a shielded infrared detector on the other. By emitting a beam of infrared light from one upright to the other, the sensor can detect when an object passes between the uprights, breaking the beam. Used for many applications...
− +
MQ-4 Gas Sensor (Natural Gas)
$4.20  
5 pc(s)
This MQ4 Gas Sensor module is useful for gas leakage detection. It is suitable for detectingI Methane, Propane, Butane, and other combustible gas. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to wide range of combustible gas High...
− +
MQ-5 Gas Sensor (LPG, Natural Gas)
$4.20  
3 pc(s)
This MQ5 Gas Sensor module is useful for gas leakage detection. It is suitable for detectingI Methane, Propane, Butane, and other combustible gas. The sensitivity of the sensor can be adjusted by potentiometer. Features High sensitivity to LPG, natural gas Low sensitivity...
− +
MQ-6 Gas Sensor (Propane, Butane and LPG)
$4.20  
3 pc(s)
This MQ6 Gas Sensor module is useful for gas leakage detection. It is suitable for detectingI Propane, Butane and LPG, and other combustible gas. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to wide range of combustible gas...
− +
PIR Motion Sensor (w/Adjustable delay and Sensitivity)
$4.20  
9 pc(s)
PIR sensors are used to detect motion from pets/humanoids from about 20 feet (~6 meters) away. This one has an adjustable delay before firing (approx 2-4 seconds) and adjustable sensitivity. You can easily reposition the sensor or mount it using the two holes on either side Runs on...
− +
MQ-2 Gas Sensor (LPG, Propane, Hydrogen, Methane)
$4.20  
2 pc(s)
This MQ2 Gas Sensor module is useful for gas leakage detection. It is suitable for detectingI LPG, Propane, Hydrogen, Methane and other combustible steam. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to wide range of combustible gas...
− +
MQ-7 Gas Sensor (Carbon Monoxide)
$4.50  
2 pc(s)
This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to Carbon...
− +
Miniature PIR Motion Sensor
$4.50  
6 pc(s)
This miniature PIR sensor is designed for motion detection. It uses pyroelectric sensor to detect motion by measuring changes in the infrared levels emitted by surrounding objects. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that...
− +
MQ-8 Gas Sensor (Hydrogen)
$4.50  
2 pc(s)
This is a simple-to-use hydrogen gas sensor, suitable for sensing hydrogen concentrations in the air. The MQ-8 can detect hydrogen gas concentrations anywhere from 100-10000ppm. This sensor has a high sensitivity and fast response time. The sensitivity of the sensor can be adjusted by...
− +
MQ-9 Gas Sensor (Carbon Monoxide / Combustible)
$4.50  
4 pc(s)
This is a simple-to-use Carbon Monoxide / Combustible gas sensor, suitable for sensing Carbon Monoxide / Combustible gas concentrations in the air. The MQ-9 can detect Carbon Monoxide / Combustible gas concentrations anywhere from 100-10000ppm. This sensor has a high sensitivity and fast...
− +
MQ-3 Gas Sensor (Alcohol)
$4.50  
3 pc(s)
This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common breathalyzer. It has a high sensitivity and fast response time. The sensitivity of the sensor can be adjusted by potentiometer. Features Good sensitivity to alcohol gas...
− +
MQ-135 Gas Sensor For Indoor Air Quality Monitor
$4.50  
2 pc(s)
This is a simple-to-use gas sensor for indoor air quality monitor, suitable for sensing NH3, NOx, alcohol, Benzene, smoke and CO2 in the air. The MQ-135 can detect NH3 and Alcohol gas concentrations anywhere from 10-300ppm and Benzene from 10-1000ppm. This sensor has a high sensitivity and...
− +
Humidity and Temperature Sensor - DHT11
$4.95  
1 pc(s)
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires...
− +
Basic Temperature-Humidity Sensor Breakout - DHT11
$5.50  
6 pc(s)
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires...
− +
-21%
LPG Gas Sensor - MQ-6
$5.95 $7.50  
1 pc(s)
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing  LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm. This sensor has a high sensitivity and fast response...
− +
-20%
TEMT6000 Breakout Board
$6.00 $7.50  
3 pc(s)
Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don't. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin. Documents: Datasheet Wiring Example...
− +
-30%
Force Sensitive Resistor - Small (FSR400) - Male Pin Header
$6.30 $9.00  
61 pc(s)
This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR,...
− +
M5Stack Module - Environmental
$6.95  
Out-of-stock
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Environmental Module is designed for sensing temperature, humidity and barometric pressure. It features two sensors - BMP280 for...
Out-of-stock
-22%
Type-K Thermocouple probe - 100mm
$6.99 $9.00  
7 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 100mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-30%
Type-K Thermocouple probe - 150mm
$6.99 $10.00  
10 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 150mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-36%
Type-K Thermocouple probe - 200mm
$6.99 $11.00  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 200mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
Pulse Oximeter & Heart-Rate Sensor - MAX30102
$6.99  
4 pc(s)
MAX30102 Sensor is an integrated pulse oximetry and heart-rate monitor module. It is equipped with a red and IR LEDs as well as a very sensitive photon detector. The idea is to pulse the different LEDs, then detect what shines back. Based on the reflected signature it's possible to measure...
− +
-7%
Type-K Thermocouple probe - 50mm
$6.99 $7.50  
5 pc(s)
This is a stainless steel Type-K Thermocouple probe for measuring temperature from 0 to 400°C. The thermocouple junction of the probe is grounded, providing faster respond to temperature change. The probe itself is 50mm long, 5mm diameter and with M8 thread. Total length of the sensor,...
− +
-20%
Load Cell - 2kg, Straight Bar
$7.90 $9.90  
20 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 2kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
-20%
Load Sensor - 50kg
$7.90 $9.90  
12 pc(s)
This load cell / sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales. Each straight bar load cell is made from an aluminum-alloy and is capable of measure up to about 50kg. Documents : Specifications Load Sensor Tutorial (NerdKits)
− +
-20%
Load Cell - 1kg, Straight Bar
$7.90 $9.90  
5 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 1kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
− +
Through-Beam Infrared Sensor Kit - 30cm
$7.90  
8 pc(s)
This Through-Beam Infrared Sensor Kit consists of two separate components: an Infrared transmitter and detector. They work by having an transmitter side that sends out a beam of human-invisible infrared light, then a detector across the way which is sensitive to that same light. When an...
− +
-20%
Load Cell - 5kg, Straight Bar
$7.90 $9.90  
Out-of-stock
This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the...
Out-of-stock
-20%
Load Cell - 10kg, Straight Bar
$7.90 $9.90  
1 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 10kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
-20%
Load Cell - 20kg, Straight Bar
$7.90 $9.90  
4 pc(s)
This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to...
− +
HC-SR04 Ultrasonic Sensor - I2C
$7.95  
15 pc(s)
This is the latest version of the popular HC-SR04 Low Cost Ultrasonic Sensor. Instead of the common GPIO interface, this version of HC-SR04 uses I2C to communicate with host controller. HC-SR04 ultrasonic sensor provides a very low-cost and easy method of distance measurement. It...
− +
Capacitive Touch Breakout - AT42QT1011
$9.50  
2 pc(s)
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1011 SparkFun Capacitive Touch Breakout offers a single, momentary capacitive touch button with easy-to-use digital I/O pins. The AT42QT1011 is a dedicated,...
− +
Force Sensitive Resistor 0.5" (FSR402) - Male Pin Header
$9.90  
1 pc(s)
This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will...
− +
Soil Moisture Sensor - Long Probe
$9.90  
Out-of-stock
This Soil Moisture Sensor is used to measure the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two long exposed metal rods function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil...
Out-of-stock
VL53L0X Time of Flight Distance Sensor - ~30 to 1000mm
$9.90  
5 pc(s)
The VL53L0X from ST Microelectronics is a time-of-flight ranging system integrated into a compact module. The sensor contains a very tiny invisible IR source, and a matching detector. It measures how long it takes for emitted pulses of infrared laser light to reach the nearest object and be...
− +
Temperature Sensor - Waterproof (DS18B20) w/Male Pin Header
$9.90  
5 pc(s)
This sealed digital temperature probe lets you precisely measure temperatures in wet environments with a simple 1-Wire interface. The DS18B20 provides 9 to 12-bit (configurable) temperature readings over a 1-Wire interface, so that only one wire (and ground) needs to be connected from a...
− +
VL6180X Time of Flight Distance Sensor - 60cm Max
$9.90  
2 pc(s)
This sensor is a breakout board for ST's VL6180X proximity and ambient light sensor, which measures the range to a target object up to 20 cm away (or 60 cm with reduced resolution). The VL6180X uses time-of-flight measurements of infrared pulses for ranging, allowing it to give accurate results...
− +
Line Follower Array
$9.95  
31 pc(s)
This SGBotic Line Follower Array gives your robot the ability to follow a dark line on a white background or vice-versa. It has four IR sensors that have been configured to output digital signal. The array features visible LEDs which turn on when the sensors detect reflected IR light. You...
− +
ACHS-7124 Current Sensor Carrier -40A to +40A
$9.95  
1 pc(s)
This board is a simple carrier of Broadcom's bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. This version accepts a bidirectional current input with a magnitude up to 40A and...
− +
ACHS-7123 Current Sensor Carrier -30A to +30A
$9.95  
2 pc(s)
This board is a simple carrier of Broadcom's bidirectional ± 30A ACHS-7123 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. This version accepts a bidirectional current input with a magnitude up to 20 A...
− +
-30%
Load Cell Amplifier - HX711
$9.95 $14.20  
3 pc(s)
This Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the amplifier to your microcontroller you will be able to read the changes in the resistance of the load cell and with some calibration you'll be able...
− +
MAX6675 Temperature Sensor Kit with K-Type Thermocouple
$9.99  
3 pc(s)
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. This MAX6675 breakout board does everything for you, and can be easily interfaced with Arduino, micro:bit, Raspberry Pi and any other microcontroller via 12-bit resolution SPI bus. A...
− +
Sensor Cable - Electrode Pads (3 connector)
$10.50  
1 pc(s)
Note : This product is  NOT  a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm...
− +
Breakout Board for Electret Microphone
$10.95  
2 pc(s)
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller's analog-to-digital converter. Each breakout comes fully assembled and works...
− +
Grove - Alcohol Sensor
$11.50  
2 pc(s)
Alcohol sensor is semiconductor sensor for alcohol detection. It has good sensitivity and fast response to alcohol, suitable for portable alcohol detector. Features : Power requirements: 5 VDC @ ~120 mA (heater on) Detection Gas: Alcohol Concentration: 20-1000ppm Alcohol Interface: 1 TTL...
− +
Sharp Infrared Distance Sensor GP2Y0A41SK0F - 4 to 30cm
$12.00  
23 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 3.1V at 4cm to 0.3V at 30cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor. See 3-pin Cable for Sharp Sensors...
− +
-7%
ISL29125 RGB Light Sensor
$12.50 $13.50  
2 pc(s)
If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, the ISL29125 breakout board may be just what you need. The ISL29125 breakout board makes it very easy to sense and record the light intensity...
− +
Adjustable Infrared Reflection Sensor (3- 80cm)
$12.50  
14 pc(s)
This is a simple to use infra-read sensor switch. Power it up with 5V and it can detects object within 3 to 80cm. It is widely used in mobile robot for obstacle detection, interactive media, industrial assembly line and many other applications. The detection distance can be adjusted...
− +
Adjustable Infrared Reflection Sensor (3- 50cm)
$12.50  
4 pc(s)
This is a simple to use infra-read sensor switch. Power it up with 5V and it can detects object within 3 to 50cm. It is widely used in mobile robot for obstacle detection, interactive media, industrial assembly line and many other applications. The detection distance can be adjusted from 3-...
− +
Sharp Infrared Distance Sensor GP2Y0A21YK - 10 to 80cm
$12.70  
2 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 3.1V at 10cm to 0.3V at 80cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor - see 3-pin cable for Sharp Sensors...
− +
-20%
MEMS Microphone Breakout - INMP401 (ADMP401)
$12.80 $16.00  
1 pc(s)
This tiny breakout board features the ADMP401 MEMs microphone. One of the key advantages to this breakout and microphone is the bottom ported input. This means the microphone's input can fit flush against the enclosure of your project. Plus you will not have to deal with trying to solder the...
− +
Electret Microphone Amplifier - MAX4466 with Adjustable Gain
$13.00  
5 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier...
− +
-15%
PIR Motion Sensor
$13.20 $15.50  
5 pc(s)
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low. Red wire is power (5 to 12V). White wire is GND. Black wire is open collector Alarm....
− +
RGB color Sensor With IR Filter & LED - TCS34725
$13.70  
Out-of-stock
The TCS34725 is probably the best color sensor on the market. It has a high sensitivity, wide dynamic range RGB and Clear light sensing elements. An integrated IR blocking filter minimizes the IR spectral component of the incoming light and allows color measurements to be made accurately. The...
Out-of-stock
Adafruit Triple-axis Magnetometer - MMC5603 - STEMMA QT / Qwiic
$13.80  
1 pc(s)
Sense the magnetic fields surrounding us with this handy triple-axis magnetometer (compass) module. Magnetometers can sense where the strongest magnetic force is coming from, generally used to detect magnetic north, but can also be used for measuring magnetic fields. This sensor tends to be...
− +
SGBotic Ultimate SR04 RGB Ultrasonic Sensor - I2C
$13.95  
Out-of-stock
Based on the design of the popular HC-SR04, SGBotic Ultimate SR04 RGB Ultrasonic Sensor offers some interesting features in addition to the solid performance of the classic HC-SR04. This sensor improves on the classic by adding a microcontroller to process the information gathered by the...
Out-of-stock
Electret Microphone Amplifier - MAX9814 with Auto Gain Control
$14.00  
2 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret...
− +
Analog Capacitive Soil Moisture Sensor- Corrosion Resistant
$14.90  
2 pc(s)
This product measures soil mositure levels by capacitive sensing, rather than resistive sensing like other types of moisture sensor. It is made of a corrosion resistant materal giving it a long service life. Insert it into soil and impress your friends with the real-time soil moisture data!...
− +
Sharp Digital Distance Sensor - 5cm
$14.95  
8 pc(s)
The  GP2Y0D805  and  GP2Y0D810  are Sharp’s smallest and fastest distance sensors. With a sample rate of almost 400 Hz and a sensing distance to 5 cm or 10 cm, respectively, these sensors provides attractive alternatives to shorter-range ...
− +
Biomedical Sensor Pad (Pack of 10)
$15.00  
Out-of-stock
Note : This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. This is a 10-pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are...
Out-of-stock
QTR-8A Reflectance Sensor Array
$15.00  
1 pc(s)
The QTR-8A reflectance sensor array is intended as a line sensor, but it can be used as a general-purpose proximity or reflectance sensor. The module is a convenient carrier for eight IR emitter and receiver (phototransistor) pairs evenly spaced at intervals of 0.375" (9.525 mm). Each...
− +
Force Sensitive Resistor - Square (FSR406) - Male Pin Header
$15.50  
4 pc(s)
This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resistance will be...
− +
-11%
Non-Invasive Current Sensor - 30A
$15.50 $17.50  
1 pc(s)
This non-invasive current sensor (also known as a “split core current transformer”) can be clamped around the supply line of an electrical load to tell you how much current is passing through it. It does this by acting as an inductor and responding to the magnetic field around a...
− +
Liquid Flow Meter - Plastic 1/2" NPS Threaded - Clear
$15.90  
Out-of-stock
Measure liquid/water flow for your solar, computer cooling, or gardening project using this handy basic flow meter. This sensor sit in line with your water line, and uses a pinwheel sensor to measure how much liquid has moved through it. The pinwheel has a little magnet attached, and there's...
Out-of-stock
M5Stack Module - Mini GPS
$16.50  
1 pc(s)
M5Stack is a robust, Arduino compatible, open source development kit with stackable modules, enabling rapid and high-quality IoT prototyping. This M5Stack Mini GPS Module is built around the AT6558 GNSS module. The 56-channel 6 positioning engine boasts a Time-To-First-Fix (TTFF) of...
− +
Sharp Infrared Distance Sensor GP2Y0A02YK - 20 to 150cm
$16.80  
5 pc(s)
This popular sensor made by Sharp produces an analog output that varies from 2.5V at 20cm to 0.4V at 150cm. The sensor has a Japanese Solderless Terminal (JST) Connector. You can purchase a pre-made cable with connector that mates with this sensor. See 3-pin Cable for Sharp Sensors...
− +
1 2