Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Sensors

Accelerometers
Barometric / Pressure
Biometrics
Capacitive / Inductive
Compass / Magneto
Current
Flex / Force
Gas
GPS
Gyros
Infra-red
IMU
LiDAR
Light / Colour
Liquid / Flow
Motion
Sound
Temperature / Humidity
Ultrasonic
1 2 3 4 5 6 7 8 9
3 - 12
Sort Alphabetically: A to Z
12 Per Page
Analog TDS (Total dissolved solids) Sensor Kit
$20.95  
3 pc(s)
This is an Arduino-compatible TDS Sensor Kit for measuring Total dissolved solids value of the water. TDS indicates how many milligrams of soluble solids dissolved in one litre of water. In general, the higher the TDS value, the more soluble solids dissolved in water, and the less clean the...
− +
Basic Temperature-Humidity Sensor Breakout - DHT11
$5.50  
6 pc(s)
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires...
− +
BH1750 Ambient Light Sensor Breakout
$23.70  
5 pc(s)
BH1750FVI is an digital Ambient Light Sensor IC for I2C bus interface. This IC is the most suitable to obtain the ambient light data for adjusting LCD and Keypad backlight power of Mobile phone. It is possible to detect wide range at High resolution. Features I2C bus...
− +
Biomedical Sensor Pad (Pack of 10)
$15.00  
Out-of-stock
Note : This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. This is a 10-pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are...
Out-of-stock
BMP280 I2C or SPI Barometric Pressure & Altitude Sensor
$18.60  
Out-of-stock
Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI!...
Out-of-stock
Breakout Board for Electret Microphone
$10.95  
2 pc(s)
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller's analog-to-digital converter. Each breakout comes fully assembled and works...
− +
Capacitive Touch Breakout - AT42QT1011
$9.50  
2 pc(s)
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1011 SparkFun Capacitive Touch Breakout offers a single, momentary capacitive touch button with easy-to-use digital I/O pins. The AT42QT1011 is a dedicated,...
− +
Electret Microphone Amplifier - MAX4466 with Adjustable Gain
$13.00  
5 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier...
− +
Electret Microphone Amplifier - MAX9814 with Auto Gain Control
$14.00  
2 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret...
− +
Flame Sensor Module
$1.90  
2 pc(s)
This Flame Sensor Module is sensitive to infra-red wavelength between 760 nm to 1100 nm that is emitted from fire flame. The module has 2 outputs: Analogue, which gives a real-time voltage output signal on thermal resistance, and Digital which allows temperature thresholds to be set via a...
− +
Flex Sensor 4.5"
$29.50  
1 pc(s)
A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the original Nintendo Power Glove . The resistance of the flex sensor changes when the metal pads...
− +
FlexiForce Adapter
$25.00  
2 pc(s)
The FlexiForce Adapter makes it easy to interface a Tekscan FlexiForce Force Sensor to your microcontroller or PC. Just use the cable included with the adapter. We even give you a round plastic disc for the sensing pad. The FlexiForce sensor is an ultra-thin and flexible printed...
− +
1 2 3 4 5 6 7 8 9
3 - 12