Store Close From 20th Sept to 3rd Oct 2023

Shipment will resume on 4th Oct 2023

Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Audio / MP3

Sort Alphabetically: A to Z
12 Per Page
3.5mm 4-Pole (TRRS) Plug w/Spring Strain Relief
$1.50  
10 pc(s)
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio...
− +
3.5mm Stereo Audio Jack Terminal Block
$1.95  
9 pc(s)
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is...
− +
3.5mm Stereo Audio Jack Terminal Block - 4-Pole (TRRS)
$1.95  
8 pc(s)
One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is...
− +
3.5mm Stereo Plug
$0.50  
13 pc(s)
This is a simple 3.5mm stereo audio plug with a screw-on plastic shroud. These are great for projects that plug into headphone jacks. Stereo plugs can also be used for carrying serial comm connections! The outer shell unscrews to reveal solder terminals on the inside of the plug. Solder on your...
− +
3.5mm Stereo Plug w/Spring Strain Relief
$1.95  
4 pc(s)
Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great plug to make your own cable with. it's made out of durable metal with a flexible, sturdy spring for strain-relief. Just solder the connector to some wires and you have a DIY audio...
− +
-30%
Breadboard-Friendly 3.5mm Stereo Headphone Jack
$1.05 $1.50  
84 pc(s)
Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 2.54mm spacing so it plugs very...
− +
Mini MP3 Module
$5.95  
5 pc(s)
The Mini MP3 Module is a small, low-cost mp3 module with a simplified audio output that can be connected directly to a speaker or an earphone jack. The module can be used as a stand-alone module with attached battery, speaker, and push buttons or used in combination with a microcontroller or...
− +
Mono 2.5W Class D Audio Amplifier - PAM8302
$8.50  
1 pc(s)
This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω...
− +
-1%
MP3 Player Shield
$39.95 $40.55  
1 pc(s)
This new revision of the MP3 player shield retains the awesome MP3 decoding abilities of the last version but adds the storage functionality of the SD card shield. Now you can pull MP3 files from an SD card and play them using only one shield, effectively turning any Arduino into a fully...
− +
-20%
MP3 Trigger
$60.00 $75.00  
1 pc(s)
Make some noise with your next project! The MP3 Trigger board is built to make it MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control,...
− +
-6%
Spectrum Shield
$39.95 $42.50  
1 pc(s)
The Spectrum Shield enables your Arduino with the capability of splitting a stereo audio input into 7-bands per channel. You can then read the amplitude of each channel using the ADC on your Arduino allowing you to control everything from LEDs to motors, pumps to relays, or even fire, all...
− +