Drivers

1 2 3
$9.90  
12 pc(s)
This A4988 Stepper Motor Driver Carrier is a breakout board for Allegro's easy-to-use A4988 microstepping bipolar stepper motor driver. The A4988 is a complete microstepping motor driver with built-in translator for easy operation. It is designed to operate bipolar stepper motors in full-,...

$28.00  
2 pc(s)
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you...

$36.75  
6 pc(s)
This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). It features a fully-dedicated PWM driver chip that handles all the motor and speed controls over I2C. Since the FeatherWing only...

$51.00  
1 pc(s)
This AutoDriver makes it easy to put the L6470 Stepper Driver (a.k.a "dSPIN") to work in your project. Simply connect your motors and your SPI-capable microcontroller and get steppin'! STMicro's L6470 is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent detection,...

$35.00  
1 pc(s)
The Big Easy Driver, designed by Brian Schmalz , is a stepper motor driver board for bi-polar stepper motors up to 2A/phase. It is based on the Allegro A4983 stepper driver chip. It's the next version of the popular Easy Driver board. Each Big Easy Driver can drive up to a max of...

$35.00  
3 pc(s)
The DELink 2 USB Link is the perfect compliment to our Kangaroo x2 self-tuning PID motion controller. Coupled with the DEScribe software, you can upload / download settings or reset the Kangaroo to factory defaults. Utilizing the easy-to-use USB bus, changing the settings on your Kangaroo...

$18.50  
10 pc(s)
This DC motor controller allows you to control both the speed and direction of a DC motor without sacrificing torque. It can provides up to a maximum continuous current of 5A to your DC motor or other DC load using a Pulse Width Modulated (PWM) with a Duty cycle fully adjustable from 10%-100%....

$22.50  
9 pc(s)
The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver.  This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the  Power Dissipation...

$7.50  
11 pc(s)
This tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair of DC motors. With an operating voltage range from 2.7 to 10.8 V and built-in protection against reverse-voltage, under-voltage, over-current, and...

$17.50  
1 pc(s)
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 6V to 30V supply to power the motor and can power any voltage of stepper motor. The...

$39.90  
Out-of-stock
Kangaroo x2 adds self-tuning feedback motion control to your Sabertooth motor driver. It can be used with quadrature encoders or potentiometers to provide position or speed control. It supports one or two feedback channels. Feedback control has always been highly desirable for...
Out-of-stock

$9.95  
57 pc(s)
This dual motor driver is based on the L298N heavy-duty dual H-bridge controller, which can be used to drive two DC motors at up to 2A each, with a voltage between 5 and 35V DC - or one stepper motor or 2 solenoids with ease. The driver has a nice heatsink to keep the L298N cool and all...
1 2 3