SGBotic Products

$9.50  
4 pc(s)
This fun little soldering kit contains all the parts required to make a 2-channel infra-red remote motor controller. The kit features a microcontroller that takes command from an infra-red receiver and controls the speed of two motors individually. Using an infra-red keypad and four AA size...

$9.50  
5 pc(s)
This fun little soldering kit enables you to make a 2-channel infra-red remote relay controller. The kit features a microcontroller that takes command from an infra-red receiver and controls 2 relays individually. Using an infra-red keypad, you will be able to turn on/off the relays....

$9.95  
6 pc(s)
When entering a carpark, a barrier bar will lift up for a car to pass through. When a train passes by, a barrier bar will come down to stop the cars from driving past. This Access Barrier Kit simulates such a barrier bar. The kit uses a servo motor to lift up/down the barrier bar and...

$8.90  
30 pc(s)
This T-Expansion For Micro:Bit is a small board that connects to the BBC micro:bit and breaks out all 19 GPIO, power and ground pin to breadboard-friendly arrangement and spacing. This board has all the pins labeled nicely so you can go forth and build circuits without keeping a pin-out...

$2.50  
6 pc(s)
This fun little soldering kit is designed for beginners to practise their soldering skill. The kit features a pair of large LEDs which will light up when power is applied. Assembly is easy, and you should be able to do it in 10-15 minutes. The kit comes with: a construction...

$8.90  
437 pc(s)
Unlock the potential of BBC Micro:bit with this assembled Breakout Board! This breakout board offers an easy way to connect additional circuits and hardware to the pins on the edge of the BBC micro:bit. It provides access to all of the BBC Micro:bit processor pins allowing a lot more extra...

$15.00  
8 pc(s)
This hand-held crank generator produces up to 15 volts of DC electricity. The integrated PCB includes a full bridge rectifier to provide the same output polarity for either direction the hand crank is turning. In addition, other devices can be easily connected to the screw terminal.

$1.95  
24 pc(s)
This is a simple adaptor to provide an easy way to mount a HC-SR04 Ultrasonic Sensor to our 2WD Robot Chassis Kit . Fully assembled, no soldering is required. Notes: Copper standoff, nuts and screws are available separately.

$9.95  
31 pc(s)
This SGBotic Line Follower Array gives your robot the ability to follow a dark line on a white background or vice-versa. It has four IR sensors that have been configured to output digital signal. The array features visible LEDs which turn on when the sensors detect reflected IR light. You...

$19.95  
2 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...

$16.00  
2 pc(s)
SGBotic has created a series of micro:bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakCode blocks package to remove the complexity of using these devices, making it easier for inventors to...

$25.95  
2 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...

$25.00  
2 pc(s)
SGBotic has created a series of micro:bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...

$95.00  
4 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...

$32.50  
1 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...

$18.00  
1 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...

$21.50  
2 pc(s)
SGBotic has created a series of Micro:Bit EduFun Mini Project Kits with an aim of making advance devices available to micro:bit inventors. Much efforts have been devoted to designing the MakeCode block packages to remove the complexity of using these devices, making it easier for inventors to...

$32.50  
4 pc(s)
This micro:bit Flex Sensor is specifically designed for micro:bit to detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. This sensors are easy to use. It will vary its resistance depending on how much it...

$15.55  
2 pc(s)
This micro:bit FSR Pressure Sensor is specifically designed for micro:bit to detect pressure. It includes a force sensitive resistor (FSR) with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The circuit...

$7.50  
12 pc(s)
This Piezo Knock Sensor is specifically designed for micro:bit to detect knock or vibration. It can be used in security or automation project by placing the Piezo element on a flat surface. When knock or vibration is detected, the sensor will generate an output voltage which can then be...

$16.95  
15 pc(s)
Looking for a liquid pump for your plant watering project? This Mini Submersible Liquid Pump Kit comes with a miniature pump with driver board and battery pack for 2xAAA battery. The driver board is designed to operate between 3V to 6VDC supply. It works with PWM input, so you can increase or...

$148.00  
Out-of-stock
Raspberry Pi3 B+ EduKit provides everything you need to start working with Raspberry Pi 3 Model B+. It comes with a Raspberry Pi 3 Model B+ (1GB RAM), a non-slip casing, cable, power supply and a formatted 8 GB SD card preloaded with Raspbian and other accessories for you to build simple...
Out-of-stock

$4.50  
6 pc(s)
This fun little soldering kit allows you to make a light activating security alarm. Using an LDR (Light dependent resistor) and an NPN transistor, the LED and buzzer will activate if light shinning on the LDR is above the pre-set threshold. The kit comes with a hardcopy construction guide....

$54.00  
2 pc(s)
Interested in making neat stuff with an Arduino but not sure where to start? This Edu-Basekit includes the latest Arduino Uno R3 with a holder, breadboard, jumper wires and other components to get you started. Great for beginners and those who want to get their feet wet but with limited...

$59.95  
5 pc(s)
SGBotic EduFun Buggy for Micro:bit is designed for learning basic robotics using BBC Micro:bit and MakeCode graphical programming. Although this kit is targeted for beginners with no prior robotic experience, experienced users will find it useful and fun too. The kit includes all parts required...

$99.00  
1 pc(s)
SGBotic EduFun Rover is specially designed for learning Arduino programming, basic robotics and sensor integration. Although the EduFun Rover is targeted for beginners with no prior robotic experience, advanced users will find it useful and fun too. The kit includes all parts that are required...

$65.00  
4 pc(s)
Interested in learning to work with Arduino but not sure where to start? This EDUKIT2 is a great way for you to get started with programming and hardware interaction with the Arduino Uno board. The kit includes the latest Arduino Uno R3 (Italy), breadboard, jumper wires, sensors, and other...

$59.00  
2 pc(s)
SGBotic IoT EduKit is designed to introduce IoT (Internet of Things) to an user with some knowledge on Arduino or other programming software but is new to IoT. The projects in this kit cover hardware interfacing, basic MQTT protocol to subscribe and publish data, as well as software tools to...

$19.95  
3 pc(s)
SGBotic Micro:bit Robot Board is designed for development of an autonomous obstacle avoidance robot or line following robot using BBC micro:bit . This Robot Board is capable of driving two DC motors. It has a dedicated port for HC-SR04 Ultrasonic Sensor and Line Follower Array . The...

$69.95  
Out-of-stock
If you are a beginner looking to learn programming and electronics, look no further than this SGBotic Micro:bit Starter Kit. This kit is designed to introduce programming and basic electronic interfacing to an user with absolutely no experience in these areas. It contains everything you need...
Out-of-stock

$14.95  
7 pc(s)
SGBotic Paper Circuits kit let you learn the basics and fundamentals of an electric circuit in a fun way! Using circuit template cards, LEDs, sound card, speaker, copper tape and coin cell batteries, you will create four circuits: simple, series, parallel and sound circuits. No prior electronics...

$183.00  
Out-of-stock
SGBotic Pi4 B EduKit provides everything you need to start working with Raspberry Pi 4 Model B. It comes with a Raspberry Pi 4 Model B (4GB RAM), casing, cable, power supply and a formatted 16GB SD card preloaded with Raspbian OS and other accessories for you to build simple projects. Included...
Out-of-stock

$13.95  
24 pc(s)
Based on the design of the popular HC-SR04, SGBotic Ultimate SR04 RGB Ultrasonic Sensor offers some interesting features in addition to the solid performance of the classic HC-SR04. This sensor improves on the classic by adding a microcontroller to process the information gathered by the...

$8.90  
245 pc(s)
This T-Expansion For Micro:Bit is a small board that connects to the BBC micro:bit and breaks out all 19 GPIO, power and ground pin to breadboard-friendly arrangement and spacing. This board has all the pins labeled nicely so you can go forth and build circuits without keeping a pin-out...

$33.50  
117 pc(s)
This ubit:connect Interfacing Board is specially designed for BBC micro:bit developer. It offers an easy way to connect sensors, actuators and other circuits to the micro:bit. The board comes with an 0.91" OLED display. Together with SGBotic's customised makecode package, this OLED display...

$7.45  
Out-of-stock
This Wind Power Kit is designed to show students how alternative energy is created by harnessing the power produced by the wind. The kit has a high efficient generator that can produce useful electricity at low speed. It can generate sufficient electricity to light up a LED by blowing onto the...
Out-of-stock

$6.95  
9 pc(s)
This Wind Power Kit is designed to show students how alternative energy is created by harnessing the power produced by the wind. The kit has a high efficient generator that can produce useful electricity at low speed. It can generate sufficient electricity to light up a LED by blowing onto the...