Robotics / Hardware

1 2 3 4 5
$129.90  
4 pc(s)
The Zumo robot is a low-profile tracked robot platform intended for use with an Arduino (or compatible device) as its main controller. It measures less than 10 cm on each side and weighs approximately 300 g with an Arduino Uno and batteries (165 g without, as shipped), so it is both small...

$0.90  
8 pc(s)
This custom-designed plastic wheel has a rubber ring measuring 44mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . It also has a slot for fitting onto our TT motor and comes with a mounting screw for secure attachment. Wheel body: ø44 x 7mm

$0.70  
Out-of-stock
This custom-designed plastic wheel has a rubber ring measuring 36mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . It also has a slot for fitting onto our TT motor and comes with a mounting screw for secure attachment. Wheel body: ø36 x 7mm
Out-of-stock

$0.60  
45 pc(s)
This custom-designed plastic wheel has a rubber ring measuring 32mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . It also has a slot for fitting onto our TT motor and comes with a mounting screw for secure attachment. Wheel body: ø32 x 7mm

$2.00  
14 pc(s)
This wheel is designed specifically for our Micro Servo 9g - Full Rotation. It comes with a rubber tread, and a press-fit design to make connecting super quick and easy. Note: Wheel only. Servo not included. Wheel body: 56 x 8mm

$2.95  
6 pc(s)
This wheel is designed specifically for our 5V stepper motor It comes with a rubber tread, and a press-fit design to make connecting super quick and easy. Note: Wheel only. Stepper motor not included. Wheel body: 56 x 8mm

$19.95  
15 pc(s)
The simple encoder kit from consists of two neodymium 8-pole magnets with rubber hubs and two hall-effect sensors terminated with 150mm (6inch) cable and 3 pin female servo headers. The magnets have 4 north poles and 4 south poles and are strong enough that the sensor can detect the poles from...

$9.80  
Out-of-stock
This custom-designed plastic wheel from Pololu has a rubber tire measuring 1.65" (42 mm) in diameter and is designed to fit the output shafts on our micro and mini metal gearmotors as well as the Solarbotics metal gear motors. Teeth on the hub optionally allow a reflectance sensor to be used...
Out-of-stock

$9.80  
1 pc(s)
This custom-designed plastic wheel has a silicone tire measuring 1.26" (32 mm) in diameter and is designed to fit the output shafts on our micro and mini metal gearmotors as well as the Solarbotics metal gear motors. Both the Micro Metal Gearmotor Bracket and Extended Micro Metal Gearmotor...

$5.20  
1 pc(s)
End caps for MakerBeam in 15x15mm profile black vinyl. We finally can give our beams little feet. This specially desinged end caps will help to protect your desktop or to prevent your MakerBeam project from slipping away. It also reduces vibrations for your construction. They...

$3.90  
4 pc(s)
End caps for MakerBeam in 10x10mm profile black vinyl. We finally can give our beams little feet. This specially desinged end caps will help to protect your desktop or to prevent your MakerBeam project from slipping away. It also reduces vibrations for your construction. They...

$8.00  
27 pc(s)
This small vibratory motor module is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. The on-board MOSFET driver allows the module to interface directly to microcontroller. Features : Operating voltage:...

$4.90  
5 pc(s)
This tiny DC motor produces vibrations by spinning an eccentric shaft at over 10,000 RPM when powered at 3 V. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback, and its small size (11.6 × 4.6 × 4.8 mm) and light weight (0.8 g) make it...

$6.50  
227 pc(s)
This itty-bitty, shaftless vibratory motor is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. All moving parts are protected within the housing. With a 2.6-3.6V operating range, these units shake crazily at 3V. Once...

$35.00  
4 pc(s)
This vacuum pump really sucks! This pump operates at 12V and has enough suction for most small projects. Features: 12V motor 12W operation 1/4" barbs 0-16" Hg vacuum range Documents: Dimensional Drawing Spec Sheet

$1.50  
203 pc(s)
This Universal Plate is compatible with Hovis Lite, Hovis Eco and HerkuleX Smart Servo Contains one bracket. Color: Green Documents: Mechanical data (STP)

$2.50  
16 pc(s)
This U4-type Bracket is compatible with Hovis Lite, Hovis Eco and HerkuleX Smart Servo Contains one bracket. Color: Green Documents: Mechanical data (STP)

$1,445.00  
1 pc(s)
Note: Netbook and 3D camera are NOT included. TurtleBot is a low-cost, personal robot kit with open-source software. With TurtleBot, you'll be able to build a robot that can drive around your house, see in 3D, and have enough horsepower to create exciting applications....

$9.95  
33 pc(s)
These TT All-Metal Gear Motors are a low cost and reliable way to get your projects moving. They look a lot like our yellow all-plastic gear motors but these have all of the motor gears machined from steel, so they won't strip as easily, and they're twice as slow (and twice as powerful) given...

$4.50  
21 pc(s)
These inexpensive and reliable TT Gear Motors are an easy, low-cost way to get your projects moving. These gear motors require a voltage of 3-6VDC with a no load current of less than 150mA at 3V and possess a stall torque of 0.8kg.cm at 6V, a gearbox ratio of 48:1, and it comes with 2 x 200mm...

$3.50  
43 pc(s)
This soft, flexible tubing is specially sourced for our Peristaltic Liquid Pump . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. Note : This tubing is sold by per meter in...

$4.50  
20 pc(s)
This soft, flexible tubing is specially sourced for our Diaphragm Liquid Pump and mini liquid pump . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. No tubing clamp is...

$3.75  
20 pc(s)
This soft, flexible tubing is specially sourced for our Mini Vacuum Pump - 6V . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. Note : This tubing is sold by per meter in...

$1.50  
Out-of-stock
This compact plastic bracket enables convenient vertical mounting of our popular Toy DC Motors . Note: Toy DC motor not included
Out-of-stock

$1.50  
79 pc(s)
This compact plastic bracket enables convenient mounting of our popular Toy DC Motors . Note: Toy DC motor not included. Documents : Dimension drawing

$0.20  
17 pc(s)
This compact metal bracket enables convenient mounting of our popular Toy DC Motors . ‎Ø2mm mounting holes. Note: Toy DC motor not included.

$110.00  
1 pc(s)
This Totem Pre-Cut Maker Kit is created for Totem beginners, but also excellent for advanced Totem makers when building smaller projects. Totem structures are designed for rapid prototyping. Adjustable part length, large variety of connection methods, easily changeable and strong...

$12.00  
5 pc(s)
Totem structures are designed for rapid prototyping. Adjustable part length, large variety of connection methods, easily changeable and strong structures make the whole prototyping process very efficient. These Totem boards are made from ABS/PC plastic. Totem Board is 10 cm x 10 cm and...

$33.00  
7 pc(s)
Totem structures are designed for rapid prototyping. Adjustable part length, large variety of connection methods, easily changeable and strong structures make the whole prototyping process very efficient. These unique beams are made from ABS/PC plastic. The design of the beam provides...

$11.50  
Out-of-stock
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 40 teeth with a gear pitch of 2mm, an outer diameter of 27.6mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 40...
Out-of-stock

$10.50  
Out-of-stock
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 36 teeth with a gear pitch of 2mm, an outer diameter of 25.4mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 36...
Out-of-stock

$9.50  
Out-of-stock
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 30 teeth with a gear pitch of 2mm, an outer diameter of 21.6mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 30...
Out-of-stock

$7.50  
Out-of-stock
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 20 teeth with a gear pitch of 2mm, an outer diameter of 16mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 20...
Out-of-stock

$4.70  
28 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm and 2mm pitch....

$8.50  
7 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 852mm,...

$7.50  
12 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 610mm,...

$6.50  
6 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 400mm,...

$5.90  
5 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 300mm,...

$5.80  
2 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 280mm,...

$5.50  
Out-of-stock
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 200mm,...
Out-of-stock

$5.10  
7 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 158mm,...

$5.00  
8 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 122mm,...

$9.90  
6 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 1220mm,...

$4.90  
3 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 112mm,...

$4.70  
7 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 110mm,...

$2.80  
14 pc(s)
This Thin White Wheel For TT Gear Motor is equipped with a rubber tread with excellent traction, and a press-fit design to make connecting super quick and easy. Note : This wheel is only for use with TT gearbox motors . Wheel body: 65 x 18mm

$59.95  
Out-of-stock
The TFMini is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 30 centimeters and as far as 12 meters! As with all LiDAR sensors, your effective detection distance will vary depending on lighting conditions and the reflectivity of your target...
Out-of-stock

$17.50  
1 pc(s)
The MakerBeamXL T-slot nut is made of stainless steel and was specially designed to slide into the T-slot grooves of the MakerBeamXL profile. The T-slot nut is great to fasten brackets or corner cubes.

$15.50  
11 pc(s)
The stainless steel T-bracket is a great addition to MakerBeamXL product range. It is compatible with both threaded and non-threaded MakerBeam. Includes 12x Stainless steel T-Bracket for MakerBeamXL

$19.50  
2 pc(s)
Looking for a DC powered liquid pump for your project? This submersible Liquid Pump operates between DC 5.5V to 12V. It comes with an inlet valve which you can adjust the flow rate manually. You also can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a...

$7.50  
2 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo draws around 35mA without load and works with 3V/5V controller including micro:bit and Arduino. Features: Rated...

$36.00  
2 pc(s)
Stepper motors are great motors for position control. They can be found in desktop printers, plotters, 3d printers, CNC milling machines, and anything else requiring precise position control. Steppers are a special segment of brushless motors. They are purposely built for high-holding torque....

$29.90  
16 pc(s)
This standard high torque servo is able to take in 6 volts and deliver an impressive 13kg-cm. of maximum torque at 0.17 sec/60°. It can rotate at approximately 180 degrees with a classic 500µS to 2500µS pulse. You can use any servo code, hardware or library to control these servos. This servo is...

$9.45  
9 pc(s)
The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled,...

$8.45  
4 pc(s)
The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled,...

$9.50  
4 pc(s)
Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 5V which makes it a great match for embedded projects. It has a throw of about 6mm and 2 M2 mounting holes on the body. The wire...

$29.95  
Out-of-stock
Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers. According to the datasheet this solenoid is rated for 36V but they work like a charm at 12V. With a throw of 10mm these solenoids are great for all kinds of motion applications such as...
Out-of-stock

$0.40  
96 pc(s)
This smooth (round) rubber belt is designed to fit on our plastic pulleys. Their elastic nature allows them to apply tension on the pulleys when stretched and the rubber construction creates excellent grip characteristics between the pulley and belt. Smooth belts can be used in a variety of...

$0.30  
94 pc(s)
This smooth (round) rubber belt is designed to fit on our plastic pulleys. Their elastic nature allows them to apply tension on the pulleys when stretched and the rubber construction creates excellent grip characteristics between the pulley and belt. Smooth belts can be used in a variety of...

$125.00  
1 pc(s)
The SMC04 high-power motor controller with feedback has multiple interface and feedback options that simplify servo control of commonly available DC motors. T he module features three independent interfaces: a serial protocol for microcontroller-based applications, a pulse-width...

$0.60  
20 pc(s)
This custom-designed plastic wheel has a rubber ring measuring 28mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø28 x 3.8mm

$0.60  
Out-of-stock
This custom-designed plastic wheel has a rubber tire measuring 26mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø26 x 7mm
Out-of-stock

$0.50  
30 pc(s)
This custom-designed plastic wheel has a rubber tire measuring 17.5mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø17.5 x 6.5mm
1 2 3 4 5