Robotics / Hardware

1 2 3 4 5
$11.90  
44 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This Mini Submersible Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump works with 7x9mm...

$4.50  
2 pc(s)
The Mini Servo / ESC Tester allow the user to test and exercise servos and set up a mode without requiring the use of a transmitter and receiver. It is easy to use and can test most servo technical parameters. It allows the user to control a servo directly to determine its neutral position...

$19.50  
15 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...

$19.50  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...

$11.90  
18 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This submersible Mini Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump works with 7x9mm...

$8.50  
14 pc(s)
Here is a simple, low-cost, high quality continuous 360° full-rotation servo motor for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as...

$7.50  
86 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....

$6.90  
2 pc(s)
This compact bracket enables convenient mounting of popular, Sanyo-style miniature metal gearmotors. The plastic bracket encloses the otherwise exposed gears, and the mounting tabs capture the nuts for easy installation. This version has mounting tabs that allow for use with the Pololu Wheel...

$19.90  
5 pc(s)
This micro metal gearmotor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Wheel 42x19mm and Wheel 32x7mm . The brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch), or you can use the mounting bracket or...

$24.90  
Out-of-stock
This cylindrical, Ø25 brushed DC gearmotor with a metal spur gearbox is designed to deliver a lot of power in a relatively small package. The motor is intended for use at 12VDC but can also run at voltages above and below this nominal voltage, so they should comfortably operate in the 9 – 15V...
Out-of-stock

$4.50  
3 pc(s)
This aluminum gearmotor brackets let you securely mount 25D mm metal gearmotors to your project. Each bracket includes two M3 screws for securing the motor to the bracket.

$15.50  
14 pc(s)
Mecanum wheels allow your robot to not only travel forward and backward, but also sideways! Nine rollers set on a 45° rotational axis parallel to the main rotational axis of the wheel enable a broad a range of movement. Rotating all four wheels in the same direction causes forward or backward...

$219.00  
5 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...

$219.00  
5 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...

$9.90  
30 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...

$9.90  
27 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...

$15.50  
30 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...

$15.50  
30 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...

$15.50  
Out-of-stock
Sometimes things do not go according to plan. We envisioned these brackets to function as linear sliders. Unfortunately the wear on a makerbeam is too high when the brackets are used under load. Instead these brackets can be used as brackets to guide vertical movement. With vertical movement...
Out-of-stock

$29.50  
8 pc(s)
The MakerBeam T-slot nut is made of stainless steel and was specially designed to slide into the T-slot grooves of the MakerBeam aluminum profile. The T-slot nut is great to fasten brackets or corner cubes. For these two purposes the nuts come with two types of bolts. The first type is a...

$13.50  
7 pc(s)
The stainless steel T-bracket is a great addition to MakerBeam product range. It is compatible with both threaded and non-threaded MakerBeam. Includes 12x Stainless steel T-Bracket

$13.50  
8 pc(s)
The stainless steel straight bracket is a great addition to MakerBeam product range. We are sure you love it too since customers regularly asked for it! Includes 12x Stainless steel Straight Bracket

$169.00  
4 pc(s)
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...

$169.00  
5 pc(s)
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...

$24.90  
10 pc(s)
1 bag of approximately 250 pcs of stainless steel M3 bolts with square head and hex hole. Length: 6mm.

$3.90  
5 pc(s)
1 bag of approximately 25 M3 bolts, 25mm - especially made for MakerBeam. The 25 mm bolts have a square head for extra tight fixing, and a hex hole in the head. Length: 25mm.

$15.00  
11 pc(s)
1 bag of approximately 100 M3 bolts, 12mm - especially made for MakerBeam. The 12 mm bolts have a square head for extra tight fixing, and a hex hole in the head. Length: 12mm.

$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. This bracket is compatible with our RBT-00490 and RBT-01415 servo motor.

$13.50  
10 pc(s)
The stainless steel right angle bracket is a great addition to MakerBeam product range. The right angle brackets give you the possibilty to place one beam on top of the other. Includes 12x Stainless steel right angle bracket

$7.90  
5 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range. This bracket is compatible with our RBT-00775 and RBT-01464 stepper motor.

$15.00  
7 pc(s)
The wing type MakerBeam bolts make it easy to add a bracket midway between brackets already fastened. The rectangular screw head of the wing type bolt gives the possibility to add screws midway. You can insert the screw midway of a beam and turn it to ensure tightening. This way it is easy to...

$7.50  
5 pc(s)
This high quality hex nut driver (5,5mm) is a standard item in our MakerBeam Starter Kit. Work with both standard nuts and Cap nuts.

$13.50  
8 pc(s)
The stainless steel corner bracket is a great addition to MakerBeam product range.Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 90 degree L-bracket

$29.50  
11 pc(s)
1 bag of MakerBeam hinges kit contains 8 hinges and 4 axes (ISO7380, M3, 14mm, A2) and 4 self locking nuts (DIN985).The hinges were specially designed to make a hinge or to mount a beam at any angle you would like.

$32.50  
3 pc(s)
Hinge bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. The 3mm inner diameter makes is easy to mount on a M3 bolt. Trebuchet movement is possible with the added copper saddle band clips,...

$24.75  
24 pc(s)
The corner cubes are designed especially for makerbeams with threaded beam ends. The bag contains: 12x Aluminum corner cubes 50x Stainless steel countersunk bolts with flat head (M3 x 6) 1x Allen key Note : Not compatible with non-threaded MakerBeam.

$21.50  
8 pc(s)
The corner cubes are designed especially for makerbeams with threaded beam ends. The bag contains: 12x Aluminum corner cubes 50x Stainless steel countersunk bolts with flat head (M3 x 6) 1x Allen key Note : Not compatible with non-threaded MakerBeam.

$12.90  
10 pc(s)
The stainless steel corner bracket is a great addition to MakerBeam product range. The corner brackets help strengthen your MakerBeam design. Includes 12x Stainless steel corner bracket

$29.00  
11 pc(s)
Stainless steel bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. If you fit it to a MakerBeam it will extend about 1.5mm from the edge of the beam. The 3mm inner diameter makes is easy to...

$14.90  
8 pc(s)
The stainless steel 60 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 60 degree bracket

$14.90  
6 pc(s)
The stainless steel 45 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 45 degree bracket

$825.00  
3 pc(s)
The MGS1600GY is a sensor capable of detecting and reporting the position of a magnetic field along its horizontal axis. The sensor is intended for line following robotic applications, using a magnetic tape to form a track guide on the floor. The sensor uses advanced signal processing...

$89.90  
Out-of-stock
The Magician Tank Mechanical Kit is a perfect starting point for putting together a mobile robot. The tank treads provide the ability to easily maneuver the bot without additional steering mechanisms. This kit covers all the mechanical parts needed, including 2 DC Gear Motors. You can...
Out-of-stock

$29.90  
56 pc(s)
The Magician Rover Chassis v2 is our latest robot platform from Dagu. It features two gearmotors with 65mm wheels and a rear caster. The chassis plates are injection molded with a wide variety of mounting holes for sensors, controllers, power, etc. Simply bolt the two plastic platforms...

$11.90  
5 pc(s)
1 bag of approximately 250 pcs M3 nuts. Compatible with all MakerBeam bolts

$15.00  
6 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...

$15.00  
8 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...

$15.00  
10 pc(s)
This gear motor is designed to operate at extremely low speed of 6rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...

$15.00  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...

$2.20  
Out-of-stock
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...
Out-of-stock

$2.00  
3 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC Checkout our mounting bracket for this motor!...

$25.00  
6 pc(s)
This low cost microstepping driver is based on the high-efficiency TB67S109AFTG IC, the maximum output current is 4.0A with 8 current options, and the microstep resolution can reach 32 (6400 steps/rev). It can take a maximum motor drive voltage of around 42V. All inputs are optically isolated...

$19.50  
21 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...

$4.50  
9 pc(s)
Large fan blade for wind energy project. 170mm in diameter and has 1.9mm center bore for 2mm motor shaft. NOTE: Toy DC motor not included. Dimensions : Ø170 x 10mm Center bore:1.9 mm

$9.95  
23 pc(s)
This dual motor driver is based on the L298N heavy-duty dual H-bridge controller, which can be used to drive two DC motors at up to 2A each, with a voltage between 5 and 35V DC - or one stepper motor or 2 solenoids with ease. The driver has a nice heatsink to keep the L298N cool and all...

$39.90  
4 pc(s)
Kangaroo x2 adds self-tuning feedback motion control to your Sabertooth motor driver. It can be used with quadrature encoders or potentiometers to provide position or speed control. It supports one or two feedback channels. Feedback control has always been highly desirable for...

$680.00  
3 pc(s)
Introducing IronBoy - a hackable humanoid robot designed to be compatible with Arduino eco-system, making it an ideal and cost-effective development platform for makers, hobbyists and educators. The IronBoy utilises IRduino controller, which is based on Arduino Leonardo, for execution of...

$29.90  
6 pc(s)
This high-torque servo now comes with metal-gear for extra-high torque (10.5 kg/cm!) and reliability! It can rotate at approximately 270 degrees with a classic 500µS to 2500µS pulse. You can use any servo code, hardware or library to control these servos. Good for applications that require...

$55.00  
8 pc(s)
Download the Arduino library here ! This Dongbu's HerkuleX DRS-0101 servo is state of the art modular smart servos that support multi-drop TTL Full Duplex UART serial communications protocol with a maxium speed of 0.667Mbps. A single command can set the speed, position, LED...

$170.00  
Out-of-stock
Download the Arduino library here ! This Dongbu's HerkuleX DRS-0201 servo is state of the art modular smart servos that support multi-drop TTL Full Duplex UART serial communications protocol with a maxium speed of 0.667Mbps. A single command can set the speed, position, LED lighting...
Out-of-stock

$52.90  
3 pc(s)
The HerkuleX Manager Kit provides a convenient way to connect the HerkuleX Smart Servo Motor to the PC. It includes an USB to serial adapter allowing direct connection to the PC's USB port. External power supply is required to power the servo. This kit is compatible with all HerkuleX Smart...

$1.60  
26 pc(s)
Interface cable for Hovis humanoid robot and HerkuleX Smart Servo. Length: 75mm

$2.50  
8 pc(s)
Interface cable for Hovis humanoid robot and HerkuleX Smart Servo. Length: 200mm
1 2 3 4 5