Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Robotics / Hardware

Roboteq
Robot Kits
MakerBeam
Motor Drivers
Motors / Servo
Mounts/Hubs
Others
Shafts
Pulleys and Belts
Pixhawk Autopilot
Wheels
1 2 3
Sort Alphabetically: A to Z
63 Per Page
Digital PWM Motor Speed Controller - 5A
$7.90  
2 pc(s)
This DC motor controller allows you to control both the speed and direction of a DC motor without sacrificing torque. It can provides up to a maximum continuous current of 5A to your DC motor or other DC load using a Pulse Width Modulated (PWM) with a Duty cycle fully adjustable from 10%-100%....
− +
DRV8825 Stepper Motor Driver Carrier, High Current
$26.95  
7 pc(s)
The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section...
− +
DRV8833 Dual Motor Driver Carrier
$18.00  
3 pc(s)
This tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair of DC motors. With an operating voltage range from 2.7 to 10.8 V and built-in protection against reverse-voltage, under-voltage, over-current, and...
− +
Dynamic Shunt Regulator (SR5K100V25R)
Contact us for details

 
 
The SR5K Shunt Regulator is a protection subsystem for dissipating the regenerative energy when braking or drastically reducing the speed of electric motors. During braking, the regenerative voltage can equal to or even exceed the supply voltage in some cases depending on the rotational inertia...
HerkuleX Interface Cable - 75mm
$1.60  
2 pc(s)
Interface cable for Hovis humanoid robot and HerkuleX Smart Servo. Length: 75mm
− +
HerkuleX Smart Servo DRS-0101 - 12kgf.cm
$55.00  
1 pc(s)
Download the Arduino library here ! This Dongbu's HerkuleX DRS-0101 servo is state of the art modular smart servos that support multi-drop TTL Full Duplex UART serial communications protocol with a maxium speed of 0.667Mbps. A single command can set the speed, position, LED lighting...
− +
High Torque Metal Gear Servo (270° Rotation)
$19.90  
3 pc(s)
This high-torque servo now comes with metal-gear for extra-high torque (10.5 kg/cm!) and reliability! It can rotate at approximately 270 degrees with a classic 500µS to 2500µS pulse. You can use any servo code, hardware or library to control these servos. Good for applications that require...
− +
L298 Dual Motor Driver Module 2A
$5.50  
3 pc(s)
This dual motor driver is based on the L298N heavy-duty dual H-bridge controller, which can be used to drive two DC motors at up to 2A each, with a voltage between 5 and 35V DC - or one stepper motor or 2 solenoids with ease. The driver has a nice heatsink to keep the L298N cool and all...
− +
Large Fan Blade - 170mm Diameter
$4.50  
6 pc(s)
Large fan blade for wind energy project. 170mm in diameter and has 1.9mm center bore for 2mm motor shaft. NOTE: Toy DC motor not included. Dimensions : Ø170 x 10mm Center bore：1.9 mm
− +
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Low Current DC Toy Motor
$2.00  
Out-of-stock
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC Checkout our mounting bracket for this motor!...
Out-of-stock
Low Current DC Toy Motor w/ Male Lead Wire
$2.20  
10 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...
− +
Low Speed Gearmotor - 3V 20rpm
$4.99  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...
− +
Low Speed Gearmotor - 3V 6rpm
$4.99  
Out-of-stock
This gear motor is designed to operate at extremely low speed of 6rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
Out-of-stock
Low Speed Gearmotor - 5V 10rpm
$4.99  
4 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...
− +
Low Speed Gearmotor - 5V 5rpm
$4.99  
3 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
− +
M3 Nuts
$11.90  
1 pc(s)
1 bag of approximately 250 pcs M3 nuts. Compatible with all MakerBeam bolts
− +
Magician Rover Chassis Kit v2
$29.90  
4 pc(s)
The Magician Rover Chassis v2 is our latest robot platform from Dagu. It features two gearmotors with 65mm wheels and a rear caster. The chassis plates are injection molded with a wide variety of mounting holes for sensors, controllers, power, etc. Simply bolt the two plastic platforms...
− +
Magnetic Guide Sensor with 3-axis Gyroscope (MGS1600GY)
[Contact us for a price]  
Out-of-stock
The MGS1600GY is a sensor capable of detecting and reporting the position of a magnetic field along its horizontal axis. The sensor is intended for line following robotic applications, using a magnetic tape to form a track guide on the floor. The sensor uses advanced signal processing...
Out-of-stock
MakerBeam 45 Degree Bracket (12 pcs)
$14.90  
6 pc(s)
The stainless steel 45 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 45 degree bracket
− +
MakerBeam 60 Degree Bracket (12 pcs)
$14.90  
7 pc(s)
The stainless steel 60 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 60 degree bracket
− +
MakerBeam Bearing
$29.00  
8 pc(s)
Stainless steel bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. If you fit it to a MakerBeam it will extend about 1.5mm from the edge of the beam. The 3mm inner diameter makes is easy to...
− +
MakerBeam Corner Bracket (12 pcs)
$12.90  
Out-of-stock
The stainless steel corner bracket is a great addition to MakerBeam product range. The corner brackets help strengthen your MakerBeam design. Includes 12x Stainless steel corner bracket
Out-of-stock
MakerBeam Corner Cube Kit - Black
$21.50  
2 pc(s)
The corner cubes are designed especially for makerbeams with threaded beam ends. The bag contains: 12x Aluminum corner cubes 50x Stainless steel countersunk bolts with flat head (M3 x 6) 1x Allen key Note : Not compatible with non-threaded MakerBeam.
− +
MakerBeam Corner Cube Kit - Clear
$24.75  
23 pc(s)
The corner cubes are designed especially for makerbeams with threaded beam ends. The bag contains: 12x Aluminum corner cubes 50x Stainless steel countersunk bolts with flat head (M3 x 6) 1x Allen key Note : Not compatible with non-threaded MakerBeam.
− +
MakerBeam Hinge Bearing
$32.50  
3 pc(s)
Hinge bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. The 3mm inner diameter makes is easy to mount on a M3 bolt. Trebuchet movement is possible with the added copper saddle band clips,...
− +
MakerBeam Hinge Kit
$29.50  
11 pc(s)
1 bag of MakerBeam hinges kit contains 8 hinges and 4 axes (ISO7380, M3, 14mm, A2) and 4 self locking nuts (DIN985).The hinges were specially designed to make a hinge or to mount a beam at any angle you would like.
− +
MakerBeam L-Bracket 90 Degree (12 pcs)
$13.50  
6 pc(s)
The stainless steel corner bracket is a great addition to MakerBeam product range.Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 90 degree L-bracket
− +
MakerBeam M3 Hex Nut Driver
$7.50  
3 pc(s)
This high quality hex nut driver (5,5mm) is a standard item in our MakerBeam Starter Kit. Work with both standard nuts and Cap nuts.
− +
MakerBeam M3 Wing Type Bolts - 6mm
$15.00  
1 pc(s)
The wing type MakerBeam bolts make it easy to add a bracket midway between brackets already fastened. The rectangular screw head of the wing type bolt gives the possibility to add screws midway. You can insert the screw midway of a beam and turn it to ensure tightening. This way it is easy to...
− +
MakerBeam NEMA 17 Bracket For Stepper Motor
$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.
− +
MakerBeam Right Angle Bracket (12 pcs)
$13.50  
2 pc(s)
The stainless steel right angle bracket is a great addition to MakerBeam product range. The right angle brackets give you the possibilty to place one beam on top of the other. Includes 12x Stainless steel right angle bracket
− +
MakerBeam Servo Bracket
$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. Documents: Mechanical drawing
− +
MakerBeam Square Headed Bolts w/ Hex Hole - M3x12
$15.00  
8 pc(s)
1 bag of approximately 100 M3 bolts, 12mm - especially made for MakerBeam. The 12 mm bolts have a square head for extra tight fixing, and a hex hole in the head. Length: 12mm.
− +
MakerBeam Square Headed Bolts w/ Hex Hole - M3x25
$3.90  
4 pc(s)
1 bag of approximately 25 M3 bolts, 25mm - especially made for MakerBeam. The 25 mm bolts have a square head for extra tight fixing, and a hex hole in the head. Length: 25mm.
− +
MakerBeam Square Headed Bolts w/ Hex Hole - M3x6
$24.90  
6 pc(s)
1 bag of approximately 250 pcs of stainless steel M3 bolts with square head and hex hole. Length: 6mm.
− +
MakerBeam Starter Kit - Black Anodised Threaded
$169.00  
Out-of-stock
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
Out-of-stock
MakerBeam Straight Bracket (12 pcs)
$13.50  
4 pc(s)
The stainless steel straight bracket is a great addition to MakerBeam product range. We are sure you love it too since customers regularly asked for it! Includes 12x Stainless steel Straight Bracket
− +
MakerBeam T-Bracket (12 pcs)
$13.50  
4 pc(s)
The stainless steel T-bracket is a great addition to MakerBeam product range. It is compatible with both threaded and non-threaded MakerBeam. Includes 12x Stainless steel T-Bracket
− +
MakerBeam T-Slot Nuts
$29.50  
Out-of-stock
The MakerBeam T-slot nut is made of stainless steel and was specially designed to slide into the T-slot grooves of the MakerBeam aluminum profile. The T-slot nut is great to fasten brackets or corner cubes. For these two purposes the nuts come with two types of bolts. The first type is a...
Out-of-stock
MakerBeamXL - 1000mm Black Anodised (Threaded)
$15.50  
22 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
MakerBeamXL - 1000mm Clear Anodised (Threaded)
$15.50  
27 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
MakerBeamXL - 500mm Black Anodised (Threaded)
$9.90  
13 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
MakerBeamXL - 500mm Clear Anodised (Threaded)
$9.90  
28 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
Mecanum Wheels For TT Gear Motor - 80mm Diameter (PAIR)
$15.50  
1 pc(s)
Mecanum wheels allow your robot to not only travel forward and backward, but also sideways! Nine rollers set on a 45° rotational axis parallel to the main rotational axis of the wheel enable a broad a range of movement. Rotating all four wheels in the same direction causes forward or backward...
− +
Metal Bracket for Ø25mm Gearmotor
$4.50  
1 pc(s)
This aluminum gearmotor brackets let you securely mount 25D mm metal gearmotors to your project. Each bracket includes two M3 screws for securing the motor to the bracket.
− +
Micro Metal Gearmotor 50:1
$19.90  
3 pc(s)
This micro metal gearmotor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Wheel 42x19mm and Wheel 32x7mm . The brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch), or you can use the mounting bracket or...
− +
Micro Metal Gearmotor Bracket Extended Pair
$6.90  
4 pc(s)
This compact bracket enables convenient mounting of popular, Sanyo-style miniature metal gearmotors. The plastic bracket encloses the otherwise exposed gears, and the mounting tabs capture the nuts for easy installation. This version has mounting tabs that allow for use with the Pololu Wheel...
− +
Micro Servo - 9g
$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....
− +
Micro Servo - 9g (360° Full Rotation)
$5.90  
Out-of-stock
Here is a simple, low-cost, high quality continuous 360° full-rotation servo motor for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as...
Out-of-stock
Mini Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
Out-of-stock
Looking for a battery powered liquid pump for your Micro:Bit project? This submersible Mini Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with...
Out-of-stock
Mini Lock-style Solenoid - 12VDC
$5.00  
8 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Lock-style Solenoid - 6VDC
$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Servo / ESC Tester
$4.50  
1 pc(s)
The Mini Servo / ESC Tester allow the user to test and exercise servos and set up a mode without requiring the use of a transmitter and receiver. It is easy to use and can test most servo technical parameters. It allows the user to control a servo directly to determine its neutral position...
− +
Mini Submersible Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
4 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This Mini Submersible Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with tubing....
− +
Mini Vacuum Pump - 6V
$9.99  
5 pc(s)
This mini vacuum pump operates at 6V and has enough suction for most small projects such as blood pressure monitors and automatic machine assembly. Features: Rated Voltage: 6VDC Rated Current: <420mA Inflation Time: <10 S (From 0 to 300 mmHg in a 500CC...
− +
Nylon Ball Caster Wheel
$1.20  
39 pc(s)
The Nylon Ball Caster has the capbility to support maximum 10kg payload. The Caster is strong and lightweight. It has 20mm high round body, with a total weight of only 25g. Documents : Dimension drawing
− +
Orange and Clear Wheel for Bi-axial Gearbox Motor - 70mm Diameter
$2.50  
10 pc(s)
Need a wheel for your Bi-axial Gear Motor ? This Orange & Clear TT Motor Wheel is equipped with a nice, thick silicone tread and a press-fit design to make connecting super quick and easy. Make cute robots today with a couple of these orange wheels! Note : This wheel is only...
− +
Pan/Tilt Bracket
$9.50  
1 pc(s)
This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. This pan/tilt bracket works with our small servo motor . Documents: Dimensional Drawing Assembly Guide
− +
Peristaltic Liquid Pump
$28.99  
Out-of-stock
Move fluid safely from here to there with this very nice little pump. Unlike most liquid pumps, this is a peristaltic type - the pump squishes the silicone tubing that contains the liquid instead of impelling it directly . The upshot? The pump never touches the fluid which makes this an...
Out-of-stock
-50%
Pulley For Toy Motor and TT Motor - 30mm Diameter
$0.15 $0.30  
45 pc(s)
This plastic pulley can be used to drive wheels or other pulleys with 2mm diameter belt. They have an outer diameter of 30mm and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . It also has a slot for fitting onto our TT motor and comes with a mounting screw for...
− +
-50%
Pulley For Toy Motor and TT Motor - 36mm Diameter
$0.15 $0.30  
46 pc(s)
This plastic pulley can be used to drive wheels or other pulleys with 2mm diameter belt. They have an outer diameter of 36mm and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . It also has a slot for fitting onto our TT motor and comes with a mounting screw for...
− +
-50%
Pulley For Toy Motorr - 17mm Diameter
$0.15 $0.30  
8 pc(s)
This plastic pulley can be used to drive wheels or other pulleys with 2mm diameter belt. They have an outer diameter of 17mm and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø17 x 4mm
− +
1 2 3