Robotics / Hardware

1 2 3
$9.50  
Out-of-stock
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
Out-of-stock

$9.50  
Out-of-stock
Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 5V which makes it a great match for embedded projects. It has a throw of about 6mm and 2 M2 mounting holes on the body....
Out-of-stock

$8.50  
1 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 852mm,...

$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...

$7.95  
12 pc(s)
These TT All-Metal Gear Motors are a low cost and reliable way to get your projects moving. They look a lot like our yellow all-plastic gear motors but these have all of the motor gears machined from steel, so they won't strip as easily, and they're twice as slow (and twice as powerful) given...

$7.90  
2 pc(s)
This is a low-cost micro size, high quality metal gear servo for all your mechatronic needs. The servo comes with a standard 3 pin power / control cable, and mounting hardware. You can use any servo code, hardware, or library to control these servos. Good for beginners who want to make stuff...

$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.

$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. Documents: Mechanical drawing

$7.90  
2 pc(s)
This DC motor controller allows you to control both the speed and direction of a DC motor without sacrificing torque. It can provides up to a maximum continuous current of 5A to your DC motor or other DC load using a Pulse Width Modulated (PWM) with a Duty cycle fully adjustable from 10%-100%....

$7.50  
3 pc(s)
This high quality hex nut driver (5,5mm) is a standard item in our MakerBeam Starter Kit. Work with both standard nuts and Cap nuts.

$6.90  
4 pc(s)
This compact bracket enables convenient mounting of popular, Sanyo-style miniature metal gearmotors. The plastic bracket encloses the otherwise exposed gears, and the mounting tabs capture the nuts for easy installation. This version has mounting tabs that allow for use with the Pololu Wheel...

$5.90  
Out-of-stock
Here is a simple, low-cost, high quality continuous 360° full-rotation servo motor for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as...
Out-of-stock

$5.50  
Out-of-stock
This dual motor driver is based on the L298N heavy-duty dual H-bridge controller, which can be used to drive two DC motors at up to 2A each, with a voltage between 5 and 35V DC - or one stepper motor or 2 solenoids with ease. The driver has a nice heatsink to keep the L298N cool and all...
Out-of-stock

$5.20  
7 pc(s)
End caps for MakerBeam in 15x15mm profile black vinyl. We finally can give our beams little feet. This specially desinged end caps will help to protect your desktop or to prevent your MakerBeam project from slipping away. It also reduces vibrations for your construction. They...

$5.00  
8 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...

$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...

$5.00  
6 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 122mm,...

$4.99  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...

$4.99  
3 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...

$4.99  
4 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...

$4.99  
Out-of-stock
This gear motor is designed to operate at extremely low speed of 6rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
Out-of-stock

$4.90  
2 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 112mm,...

$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....

$4.90  
3 pc(s)
This small stepper is a great way to get things moving, especially when positioning and repeatability is a concern. The stepper motor has five color-coded wires allow it to be controlled by both unipolar and bipolar stepper motor drivers. All five wires are used when connect to a unipolar...

$4.80  
2 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 36 teeth with a gear pitch of 2mm, an outer diameter of 25.4mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 36...

$4.70  
11 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm and 2mm pitch....

$4.70  
5 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 110mm,...

$4.50  
1 pc(s)
The Mini Servo / ESC Tester allow the user to test and exercise servos and set up a mode without requiring the use of a transmitter and receiver. It is easy to use and can test most servo technical parameters. It allows the user to control a servo directly to determine its neutral position...

$4.50  
42 pc(s)
This soft, flexible tubing is specially sourced for our Diaphragm Liquid Pump and mini liquid pump . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. No tubing clamp is...

$4.50  
1 pc(s)
This aluminum gearmotor brackets let you securely mount 25D mm metal gearmotors to your project. Each bracket includes two M3 screws for securing the motor to the bracket.

$4.50  
6 pc(s)
Large fan blade for wind energy project. 170mm in diameter and has 1.9mm center bore for 2mm motor shaft. NOTE: Toy DC motor not included. Dimensions : Ø170 x 10mm Center bore:1.9 mm

$4.50  
6 pc(s)
These inexpensive and reliable TT Gear Motors are an easy, low-cost way to get your projects moving. These gear motors require a voltage of 3-6VDC with a no load current of less than 150mA at 3V and possess a stall torque of 0.8kg.cm at 6V, a gearbox ratio of 48:1, and it comes with 2 x 200mm...

$4.50  
10 pc(s)
Looking for a battery powered liquid pump? This non-submersible diaphragm liquid pump will operates between DC 6V to 12V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. Each diaphragm liquid pump comes with a pair of...

$4.50  
4 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 30 teeth with a gear pitch of 2mm, an outer diameter of 21.6mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 30...

$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...

$3.95 $5.90  
4 pc(s)
This tiny DC motor produces vibrations by spinning an eccentric shaft at over 10,000 RPM when powered at 3 V. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback, and its small size (11.6 × 4.6 × 4.8 mm) and light weight (0.8 g) make it...

$3.95  
4 pc(s)
Savonius Vertical Rotor Blade for your wind energy experiment. It push fits directly onto our toy DC motor . Dimensions : Ø50 x 60mm (assembled) Center bore:1.9 mm

$3.90  
6 pc(s)
End caps for MakerBeam in 10x10mm profile black vinyl. We finally can give our beams little feet. This specially desinged end caps will help to protect your desktop or to prevent your MakerBeam project from slipping away. It also reduces vibrations for your construction. They...

$3.90  
4 pc(s)
1 bag of approximately 25 M3 bolts, 25mm - especially made for MakerBeam. The 25 mm bolts have a square head for extra tight fixing, and a hex hole in the head. Length: 25mm.

$3.50  
1 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 400mA while possessing a gearbox ratio of 1:94 and a wheel...

$3.50  
4 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 660mA while possessing a gearbox ratio of 1:134 and a wheel...

$3.50  
19 pc(s)
This soft, flexible tubing is specially sourced for our Peristaltic Liquid Pump . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. Note : This tubing is sold by per meter in...

$3.25  
16 pc(s)
This small vibratory motor module is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. The on-board MOSFET driver allows the module to interface directly to microcontroller. Features : Operating voltage:...

$2.95  
4 pc(s)
This wheel is designed specifically for our 5V stepper motor It comes with a rubber tread, and a press-fit design to make connecting super quick and easy. Note: Wheel only. Stepper motor not included. Wheel body: 56 x 8mm

$2.95  
1 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This submersible Mini Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with...

$2.95  
6 pc(s)
Looking for a battery powered liquid pump for your Micro:Bit project? This Mini Submersible Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with tubing....

$2.50  
3 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 20 teeth with a gear pitch of 2mm, an outer diameter of 16mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 20...

$2.50  
10 pc(s)
Need a wheel for your Bi-axial Gear Motor ? This Orange & Clear TT Motor Wheel is equipped with a nice, thick silicone tread and a press-fit design to make connecting super quick and easy. Make cute robots today with a couple of these orange wheels! Note : This wheel is only...

$2.50  
11 pc(s)
Small fiber reinforced nylon propeller for boat, 3 blades and 40mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø40 x 18.5mm Center bore:1.9 mm

$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm

$2.20  
13 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...

$2.00  
6 pc(s)
This wheel is designed specifically for our Micro Servo 9g - Full Rotation. It comes with a rubber tread, and a press-fit design to make connecting super quick and easy. Note: Wheel only. Servo not included. Wheel body: 56 x 8mm

$2.00 $2.50  
46 pc(s)
This itty-bitty, shaftless vibratory motor is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. All moving parts are protected within the housing. With a 2.6-3.6V operating range, these units shake crazily at 3V. Once...

$2.00  
4 pc(s)
Small nylon propeller for port and starboard thruster. Featuring both left- and right-handed rotation. 3 blades and 36mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø36 x 18.5mm Center bore:1.9 mm

$2.00  
Out-of-stock
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC Checkout our mounting bracket for this motor!...
Out-of-stock

$1.95  
12 pc(s)
This Thin White Wheel For TT Gear Motor is equipped with a rubber tread with excellent traction, and a press-fit design to make connecting super quick and easy. Note : This wheel is only for use with TT gearbox motors . Wheel body: 65 x 18mm

$1.95  
5 pc(s)
This Rubber Wheel For TT Gear Motor is equipped with a nice, thick rubber tread with excellent traction, and a press-fit design to make connecting super quick and easy. Note : This wheel is only for use with TT gearbox motors . Wheel body: 65 x 28mm

$1.60  
2 pc(s)
Interface cable for Hovis humanoid robot and HerkuleX Smart Servo. Length: 75mm

$1.50  
13 pc(s)
This compact plastic bracket enables convenient mounting of our popular Toy DC Motors . Note: Toy DC motor not included. Documents : Dimension drawing

$1.50  
14 pc(s)
This custom-designed plastic wheel has a rubber tire measuring 17.5mm in diameter and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø17.5 x 6.5mm

$1.20  
39 pc(s)
The Nylon Ball Caster has the capbility to support maximum 10kg payload. The Caster is strong and lightweight. It has 20mm high round body, with a total weight of only 25g. Documents : Dimension drawing

$0.80  
6 pc(s)
Small 4 blade propeller, 80mm in diameter. It push fits directly onto our toy DC motor . NOTE: Toy DC motor not included. Dimensions : Ø80 x 12.8mm Center bore:1.9 mm

$0.75 $1.50  
57 pc(s)
This Swivel Caster Wheel is perfect for use with 2-wheeled robots that need a third-point of support. The nylon wheel comes attached to a metal plate and with M4 screw holes for fastening to any robot or project. It can rotate a full 360° on the plate and the sleek silver metal look suits any...
1 2 3