Robotics / Hardware

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
9 - 16
$4.90  
3 pc(s)
This small stepper is a great way to get things moving, especially when positioning and repeatability is a concern. The stepper motor has five color-coded wires allow it to be controlled by both unipolar and bipolar stepper motor drivers. All five wires are used when connect to a unipolar...

$4.90  
2 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 112mm,...

$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....

$4.80  
2 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 36 teeth with a gear pitch of 2mm, an outer diameter of 25.4mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 36...

$4.70  
11 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm and 2mm pitch....

$4.70  
5 pc(s)
These are resistant 2GT sized timing belts that fit snug inside of these timing pulleys . Each belt is manufactured from wear resistant Polyurethane and high tensile steel cord to provide a fair ammount of strength and durability. The timing belts have a width of 6mm, a length of 110mm,...

$4.50  
6 pc(s)
These inexpensive and reliable TT Gear Motors are an easy, low-cost way to get your projects moving. These gear motors require a voltage of 3-6VDC with a no load current of less than 150mA at 3V and possess a stall torque of 0.8kg.cm at 6V, a gearbox ratio of 48:1, and it comes with 2 x 200mm...

$4.50  
10 pc(s)
Looking for a battery powered liquid pump? This non-submersible diaphragm liquid pump will operates between DC 6V to 12V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. Each diaphragm liquid pump comes with a pair of...

$4.50  
4 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 30 teeth with a gear pitch of 2mm, an outer diameter of 21.6mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 30...

$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...

$4.50  
1 pc(s)
The Mini Servo / ESC Tester allow the user to test and exercise servos and set up a mode without requiring the use of a transmitter and receiver. It is easy to use and can test most servo technical parameters. It allows the user to control a servo directly to determine its neutral position...

$4.50  
39 pc(s)
This soft, flexible tubing is specially sourced for our Diaphragm Liquid Pump and mini liquid pump . It is made of silicone rubber which is odorless, flexible and resistant to high temperatures. It can be operated under a temperature range of -60 to +200℃. No tubing clamp is...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
9 - 16