DC/Gearmotor

$56.50  
2 pc(s)
This gearmotor consists of a Low -power, 6 V brushed DC motor combined with a 46.85:1 metal spur gearbox, and it has an integrated 48 CPR quadrature encoder on the motor shaft, which provides 2248.86 counts per revolution of the gearbox's output shaft. The gearmotor is cylindrical, with...

$4.50  
6 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 660mA while possessing a gearbox ratio of 1:134 and a wheel...

$4.50  
6 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 400mA while possessing a gearbox ratio of 1:94 and a wheel...

$2.00  
61 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC Checkout our mounting bracket for this motor!...

$2.20  
Out-of-stock
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...
Out-of-stock

$15.00  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...

$15.00  
10 pc(s)
This gear motor is designed to operate at extremely low speed of 6rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...

$15.00  
8 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...

$15.00  
6 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...

$24.90  
Out-of-stock
This cylindrical, Ø25 brushed DC gearmotor with a metal spur gearbox is designed to deliver a lot of power in a relatively small package. The motor is intended for use at 12VDC but can also run at voltages above and below this nominal voltage, so they should comfortably operate in the 9 – 15V...
Out-of-stock

$19.90  
5 pc(s)
This micro metal gearmotor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Wheel 42x19mm and Wheel 32x7mm . The brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch), or you can use the mounting bracket or...

$4.50  
17 pc(s)
These inexpensive and reliable TT Gear Motors are an easy, low-cost way to get your projects moving. These gear motors require a voltage of 3-6VDC with a no load current of less than 150mA at 3V and possess a stall torque of 0.8kg.cm at 6V, a gearbox ratio of 48:1, and it comes with 2 x 200mm...

$9.95  
33 pc(s)
These TT All-Metal Gear Motors are a low cost and reliable way to get your projects moving. They look a lot like our yellow all-plastic gear motors but these have all of the motor gears machined from steel, so they won't strip as easily, and they're twice as slow (and twice as powerful) given...