Breakout Boards

$1.95  
9 pc(s)
An adjustable potentiometer can open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC, GND, and the OUT pin will have a voltage that varies from 0 to VCC depending on the rotation of the pot. Hook the OUT pin to an ADC on a microcontroller and get a...

$1.95 $3.90  
5 pc(s)
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm)....

$2.50  
4 pc(s)
The rotary encoder is a rotary input device that provides an indication of how much and in which direction the encoder has been turned. This 20-pulse Rotary Encoder Breakout has a nice 'clicking' feel and also has a push-button built into it so you can press onto the knob to close a separate...

$2.50 $5.00  
6 pc(s)
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm)....

$3.15 $6.30  
14 pc(s)
8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm)....

$3.15 $6.30  
22 pc(s)
Low-cost basic SOIC break out boards. These are custom PCB boards that interface standard SOIC devices to standard .1" (2.54mm) headers. 28-SOIC: Standard .6" spacing between pins. Will fit directly into a standard width (600 mil) DIP socket. For wide ICs (memories, drivers, 74s,...

$3.20  
1 pc(s)
If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The 8-channel Bi-directional Logic Level Converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V...

$3.95  
2 pc(s)
This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a miniUSB/USB miniB connector to your breadboard - here it is. Also good for an un-regulated, non-limited 5V supply up to 100mA.

$3.95 $4.95  
1 pc(s)
The SparkFun 8-Pin SOIC to DIP Adapter is a small PCB that lets you adapt SOIC packages into a DIP footprint. These tiny boards are useful for modding and upgrading devices that use 8-pin DIP ICs, when the upgraded IC is only available in a SOIC footprint. You can also use these adapters for...

$4.80  
3 pc(s)
This simple interface board convert 20pins 1.27mm (0.05") pin header to 2.54mm (0.1") pin header. It works with J-Link EDU Mini Programmer .

$6.50 $6.95  
1 pc(s)
This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you. Dimensions : 1.02 x 0.9" (26.06 x 22.93mm)...

$8.50  
1 pc(s)
This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω...

$9.95  
3 pc(s)
This is a breakout board for the very handy 16-Channel Analog/Digital Mulitplexer/Demultiplexer CD74HC4067. This chip can be used to connect 16 analog sources (like sensors) to 5 pins on a microcontroller. 4 of the pins must be digital pins, 1 pin must be an analog to digital conversion pin....

$10.95  
2 pc(s)
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller's analog-to-digital converter. Each breakout comes fully assembled and works...

$11.90  
4 pc(s)
This Level Shifting microSD Breakout from Sparkfun is quite similar to the microSD Transflash Breakout, but with the included level shifting hardware, this board allows you to utilize a microSD card at Arduino's SD library's top speed on a 5V system. With this small breakout board, that is...

$11.95  
5 pc(s)
Unlike most computers, the Pi lacks a Real-Time Clock (RTC). This means the Pi doesn't know what time it is when powered on. While your Pi is connected to a network it will be able to set it's clock correctly using NTP ( Network Time Protocol ) server. Without a network connection your Pi...

$13.00  
5 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier...

$14.00  
2 pc(s)
Add an ear to your project with this well-designed electret microphone amplifier with AGC. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX9814, a specialty chip that is designed for amplifying electret...

$15.75 $17.00  
5 pc(s)
The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at...

$23.00 $24.50  
2 pc(s)
The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at...