Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Motors / Servo

Sort Alphabetically: A to Z
63 Per Page
5V Stepper Motor w/ULN2003 Driver
$4.90  
3 pc(s)
This small stepper is a great way to get things moving, especially when positioning and repeatability is a concern. The stepper motor has five color-coded wires allow it to be controlled by both unipolar and bipolar stepper motor drivers. All five wires are used when connect to a unipolar...
− +
Bi-axial Gear Motor (1:143)
$3.50  
4 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 660mA while possessing a gearbox ratio of 1:134 and a wheel...
− +
Bi-axial Gear Motor (1:94)
$3.50  
1 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 400mA while possessing a gearbox ratio of 1:94 and a wheel...
− +
HerkuleX Interface Cable - 75mm
$1.60  
2 pc(s)
Interface cable for Hovis humanoid robot and HerkuleX Smart Servo. Length: 75mm
− +
HerkuleX Smart Servo DRS-0101 - 12kgf.cm
$55.00  
1 pc(s)
Download the Arduino library here ! This Dongbu's HerkuleX DRS-0101 servo is state of the art modular smart servos that support multi-drop TTL Full Duplex UART serial communications protocol with a maxium speed of 0.667Mbps. A single command can set the speed, position, LED lighting...
− +
High Torque Metal Gear Servo (270° Rotation)
$19.90  
3 pc(s)
This high-torque servo now comes with metal-gear for extra-high torque (10.5 kg/cm!) and reliability! It can rotate at approximately 270 degrees with a classic 500µS to 2500µS pulse. You can use any servo code, hardware or library to control these servos. Good for applications that require...
− +
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Low Current DC Toy Motor w/ Male Lead Wire
$2.20  
10 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...
− +
Low Speed Gearmotor - 3V 20rpm
$4.99  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...
− +
Low Speed Gearmotor - 5V 10rpm
$4.99  
4 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...
− +
Low Speed Gearmotor - 5V 5rpm
$4.99  
3 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
− +
MakerBeam NEMA 17 Bracket For Stepper Motor
$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.
− +
MakerBeam Servo Bracket
$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. Documents: Mechanical drawing
− +
Micro Metal Gearmotor 50:1
$19.90  
3 pc(s)
This micro metal gearmotor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Wheel 42x19mm and Wheel 32x7mm . The brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch), or you can use the mounting bracket or...
− +
Micro Servo - 9g
$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....
− +
Micro Servo - 9g (360° Full Rotation)
$5.90  
Out-of-stock
Here is a simple, low-cost, high quality continuous 360° full-rotation servo motor for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as...
Out-of-stock
Mini Lock-style Solenoid - 12VDC
$5.00  
8 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Lock-style Solenoid - 6VDC
$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Servo / ESC Tester
$4.50  
1 pc(s)
The Mini Servo / ESC Tester allow the user to test and exercise servos and set up a mode without requiring the use of a transmitter and receiver. It is easy to use and can test most servo technical parameters. It allows the user to control a servo directly to determine its neutral position...
− +
-20%
Servo - Generic Metal Gear (Micro Size)
$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...
− +
-20%
Small Stepper Motor
$11.60 $14.50  
1 pc(s)
These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. Features : Stride Angle (degrees) : 7.5 2-Phase Rated Voltage : 12V Rated Current : 400mA 3mm Diameter Drive Shaft...
− +
Standard Metal Gear Micro Servo
$7.90  
2 pc(s)
This is a low-cost micro size, high quality metal gear servo for all your mechatronic needs. The servo comes with a standard 3 pin power / control cable, and mounting hardware. You can use any servo code, hardware, or library to control these servos. Good for beginners who want to make stuff...
− +
TT Gear Motor - 200RPM
$4.50  
6 pc(s)
These inexpensive and reliable TT Gear Motors are an easy, low-cost way to get your projects moving. These gear motors require a voltage of 3-6VDC with a no load current of less than 150mA at 3V and possess a stall torque of 0.8kg.cm at 6V, a gearbox ratio of 48:1, and it comes with 2 x 200mm...
− +
TT Gear Motor All-Metal Gearbox - 1:90 Gear Ratio
$7.95  
12 pc(s)
These TT All-Metal Gear Motors are a low cost and reliable way to get your projects moving. They look a lot like our yellow all-plastic gear motors but these have all of the motor gears machined from steel, so they won't strip as easily, and they're twice as slow (and twice as powerful) given...
− +
-20%
Vibration Motor - 10x3.15mm
$2.00 $2.50  
46 pc(s)
This itty-bitty, shaftless vibratory motor is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. All moving parts are protected within the housing. With a 2.6-3.6V operating range, these units shake crazily at 3V. Once...
− +
-33%
Vibration Motor 11.6×4.6×4.8mm
$3.95 $5.90  
4 pc(s)
This tiny DC motor produces vibrations by spinning an eccentric shaft at over 10,000 RPM when powered at 3 V. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback, and its small size (11.6 × 4.6 × 4.8 mm) and light weight (0.8 g) make it...
− +
Vibration Motor Module
$3.25  
16 pc(s)
This small vibratory motor module is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. The on-board MOSFET driver allows the module to interface directly to microcontroller. Features : Operating voltage:...
− +