Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Motors / Servo

1 2 3
Sort Alphabetically: A to Z
12 Per Page
5V Stepper Motor w/ULN2003 Driver
$4.90  
3 pc(s)
This small stepper is a great way to get things moving, especially when positioning and repeatability is a concern. The stepper motor has five color-coded wires allow it to be controlled by both unipolar and bipolar stepper motor drivers. All five wires are used when connect to a unipolar...
− +
Bi-axial Gear Motor (1:143)
$3.50  
4 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 660mA while possessing a gearbox ratio of 1:134 and a wheel...
− +
Bi-axial Gear Motor (1:94)
$3.50  
1 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 400mA while possessing a gearbox ratio of 1:94 and a wheel...
− +
HerkuleX Interface Cable - 75mm
$1.60  
2 pc(s)
Interface cable for Hovis humanoid robot and HerkuleX Smart Servo. Length: 75mm
− +
HerkuleX Smart Servo DRS-0101 - 12kgf.cm
$55.00  
1 pc(s)
Download the Arduino library here ! This Dongbu's HerkuleX DRS-0101 servo is state of the art modular smart servos that support multi-drop TTL Full Duplex UART serial communications protocol with a maxium speed of 0.667Mbps. A single command can set the speed, position, LED lighting...
− +
High Torque Metal Gear Servo (270° Rotation)
$19.90  
3 pc(s)
This high-torque servo now comes with metal-gear for extra-high torque (10.5 kg/cm!) and reliability! It can rotate at approximately 270 degrees with a classic 500µS to 2500µS pulse. You can use any servo code, hardware or library to control these servos. Good for applications that require...
− +
-20%
Lock-style Solenoid - 12VDC
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Low Current DC Toy Motor w/ Male Lead Wire
$2.20  
10 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...
− +
Low Speed Gearmotor - 3V 20rpm
$4.99  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...
− +
Low Speed Gearmotor - 5V 10rpm
$4.99  
4 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...
− +
Low Speed Gearmotor - 5V 5rpm
$4.99  
3 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
− +
MakerBeam NEMA 17 Bracket For Stepper Motor
$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.
− +
1 2 3