Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Motors / Servo

1 2 3
Sort Alphabetically: A to Z
12 Per Page
MakerBeam Servo Bracket
$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. Documents: Mechanical drawing
− +
Micro Metal Gearmotor 50:1
$19.90  
3 pc(s)
This micro metal gearmotor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Wheel 42x19mm and Wheel 32x7mm . The brass faceplate has two mounting holes threaded for M1.6 screws (1.6 mm diameter, 0.35 mm thread pitch), or you can use the mounting bracket or...
− +
Micro Servo - 9g
$4.90  
11 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as shown. It works with micro:bit v2....
− +
Micro Servo - 9g (360° Full Rotation)
$5.90  
Out-of-stock
Here is a simple, low-cost, high quality continuous 360° full-rotation servo motor for all your mechatronic needs. Small servo with a standard 3 pin power, control cable, and mounting hardware. This servo is very similar in size and specifications to the Hitec HS-55. Includes hardware as...
Out-of-stock
Mini Lock-style Solenoid - 12VDC
$5.00  
8 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Lock-style Solenoid - 6VDC
$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
Mini Servo / ESC Tester
$4.50  
1 pc(s)
The Mini Servo / ESC Tester allow the user to test and exercise servos and set up a mode without requiring the use of a transmitter and receiver. It is easy to use and can test most servo technical parameters. It allows the user to control a servo directly to determine its neutral position...
− +
-20%
Servo - Generic Metal Gear (Micro Size)
$7.95 $9.95  
202 pc(s)
Here is a simple, low-cost, high quality servo for all your mechatronic needs. This servo is able to take in 6 volts and deliver 3.2kg of maximum torque at 0.18 sec/60° This is a small servo with a standard 3 pin power and control cable (red = power, brown = ground, and yellow = data). The...
− +
-20%
Small Stepper Motor
$11.60 $14.50  
1 pc(s)
These small steppers are a great way to get things moving, especially when positioning and repeatability is a concern. Features : Stride Angle (degrees) : 7.5 2-Phase Rated Voltage : 12V Rated Current : 400mA 3mm Diameter Drive Shaft...
− +
Standard Metal Gear Micro Servo
$7.90  
2 pc(s)
This is a low-cost micro size, high quality metal gear servo for all your mechatronic needs. The servo comes with a standard 3 pin power / control cable, and mounting hardware. You can use any servo code, hardware, or library to control these servos. Good for beginners who want to make stuff...
− +
TT Gear Motor - 200RPM
$4.50  
6 pc(s)
These inexpensive and reliable TT Gear Motors are an easy, low-cost way to get your projects moving. These gear motors require a voltage of 3-6VDC with a no load current of less than 150mA at 3V and possess a stall torque of 0.8kg.cm at 6V, a gearbox ratio of 48:1, and it comes with 2 x 200mm...
− +
TT Gear Motor All-Metal Gearbox - 1:90 Gear Ratio
$7.95  
12 pc(s)
These TT All-Metal Gear Motors are a low cost and reliable way to get your projects moving. They look a lot like our yellow all-plastic gear motors but these have all of the motor gears machined from steel, so they won't strip as easily, and they're twice as slow (and twice as powerful) given...
− +
1 2 3