Power / Batteries

1 2
$0.80  
3 pc(s)
Battery holder for single AA batteries, terminated with ~150mm leads

$1.00 $1.85  
19 pc(s)
This 1xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable sliding cover and an ON/OFF switch which can be used to control power to your project. The leads are about 150mm, and the last 5mm of them are tinned. Dimensions: 69 x 26...

$15.50  
2 pc(s)
This 10A Relay Module is a little different to the other relays in our store - not only is it compatible with 5V Arduino boards, but also with Raspberry Pi, BBB (BeagleBoard Black), mbed, Intel Joule, Arduino 101 and other 3.3V devices. It is specially designed for low-voltage devices and...

$14.50  
4 pc(s)
This D24V10F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 85% and 90% and has a very low dropout, so it can be used with input...

$0.80 $1.00  
Out-of-stock
Battery holder for two AA batteries, terminated with ~150mm leads
Out-of-stock

$1.90  
29 pc(s)
This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project. The leads are about...

$0.80 $1.00  
7 pc(s)
Battery holder for two AAA batteries, terminated with ~150mm leads

$2.25  
Out-of-stock
This 2xAAA Battery Holder with Switch and JST Connector is compatible with the BBC micro:bit. Supplied with ~150mm colour coded power leads and a JST connector at the end, this battery holder is light and can be attached to the back of BBC micro:bit cases. This battery holder features a lid...
Out-of-stock

$1.90  
14 pc(s)
Enclosed battery holder for two AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are about...

$1.40  
1 pc(s)
This 2xAAA Battery Cage with JST connector is compatible with the BBC micro:bit. Supplied with colour coded power leads and a JST connector at the end, this battery cage is light and features a M3 mounting hole in the centre so it can be attached to the back of BBC micro:bit cases. The JST...

$0.50 $1.00  
84 pc(s)
Battery holder for three AA batteries, terminated with ~150mm leads

$1.00 $2.00  
1 pc(s)
Enclosed battery holder for three AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$0.50 $1.00  
50 pc(s)
Battery holder for three AAA batteries, terminated with ~150mm leads

$1.00 $2.00  
14 pc(s)
Enclosed battery holder for three AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$18.50  
6 pc(s)
The Pololu step-up/step-down voltage regulator S7V8F3 is a switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC converter) that uses a buck-boost topology. It takes an input voltage from 2.7 V to 11.8 V and increases or decreases the voltage to a fixed 3.3 V output...

$14.50  
5 pc(s)
This D24V10F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.3V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 80% and 90% and has a very low dropout, so it can be used with input...

$35.00  
10 pc(s)
This D24V25F3 synchronous buck voltage regulator takes an input voltage of up to 38 V and efficiently reduces it to 3.3 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.5 A and features reverse voltage protection. Typical efficiencies of 80%...

$3.00  
7 pc(s)
Battery holder for four 18650 Lithium Ion batteries, terminated with ~150mm leads

$1.00 $1.20  
23 pc(s)
Battery holder for four AA batteries, terminated with ~150mm leads

$1.20 $1.50  
36 pc(s)
This is a simple 4 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector. The connector mates with the barrel jack on the Arduino Uno (among a number of other products) allowing you to easily make your project...

$2.50  
3 pc(s)
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$2.80  
5 pc(s)
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$3.50  
8 pc(s)
This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable sliding cover and an ON/OFF switch which can be used to control power to your project. The cable is terminated with a standard 5.5x2.1mm, center positive barrel jack...

$2.00 $2.50  
13 pc(s)
Enclosed battery holder for four AAA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$1.30  
21 pc(s)
Battery holder for five AA batteries, terminated with ~150mm leads

$25.50  
4 pc(s)
The Pololu step-up/step-down voltage regulator S7V7F5 is a switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC converter) that uses a buck-boost topology. It takes an input voltage from 2.7 V to 11.8 V and increases or decreases the voltage to a fixed 5 V output...

$1.40  
19 pc(s)
Battery holder for six AA batteries, terminated with ~150mm leads

$2.90  
15 pc(s)
Enclosed battery holder for six AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose the cells. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$1.00 $1.50  
17 pc(s)
Battery holder for eight AA batteries with ~140mm leads, cube end-to-end configuration.

$3.80  
2 pc(s)
Enclosed battery holder for eight AA batteries. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$1.50  
2 pc(s)
This is a simple Battery holder for eight AA cells arranged as two back-to-back four-cell holders.

$0.80  
6 pc(s)
This 9V battery holder allows your battery to snap in tight and holds it in place, which is great in situations where you don't want the battery just hanging. It also has three mounting holes so you can attach it securely to your enclosure. It is terminated with a 150mm leads

$1.80 $2.00  
6 pc(s)
Enclosed battery holder for 9V battery. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$2.50  
5 pc(s)
Enclosed battery holder for 9V battery. This holder features a lid that slides over the batteries and snaps into place to fully enclose the battery. It also features a switch that lets you open and close the electrical connection between the batteries and the holder's leads. The leads are...

$2.80  
Out-of-stock
This is a 9V battery pack with on/off switch and terminated with a standard 5.5x2.1mm, center-positive barrel jack. Use this to battery-power your Arduino or other electronic projects. Battery & screw not included. Dimensions : 68mm x 33mm x 21mm Lead length: 12cm...
Out-of-stock

$0.80  
50 pc(s)
9V snap connector wth hard shell that is built stronger to last longer. Comes with color-coded wire leads. Great for replacements or projects. Length: ~ 15cm

$0.50  
94 pc(s)
Classis 9V snap connectors with color-coded wire leads. Great for replacements or projects. Length: ~ 15cm

$0.90 $1.80  
75 pc(s)
This 9V Snap to 2.1mm Barrel Jack Adapter provides the ability to conveniently use a 9V battery to power many common boards and modules such as the popular Arduino and compatible microcontrollers. This plug is a common barrel type with an outside diameter of 5.5mm and an inside diameter of...

$2.95  
2 pc(s)
This is a simple cable that adapts from a USB port to a 5.5x2.1mm barrel connector, center positive. This cable allows the user to use a USB port on a computer, laptop, or on our cigarette power supply to provide our development boards with 5V. The USB specification limits current...

$12.50  
1 pc(s)
Your 5V system can wield great power with this big, beefy relay board. How does 10A on the NC contacts and 20A on the NO contacts at 220VAC sound? The SparkFun Beefcake Relay Control Kit contains all the parts you need to get your high-power load under control. Only minimal assembly is...

$2.95  
5 pc(s)
This Breadboard Power Supply Module plugs directly into a solderless breadboard and provides both 3.3V and 5V power directly to the breadboard power rails. The board accepts 7 to 12V DC input via the barrel jack or 5V via the mini-B USB port. It provides two regulated, fuse protected outputs...

$2.50  
4 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. If you have a power supply with a barrel jack and want to plug it into a breadboard, this might be the simple solution.

$2.50  
36 pc(s)
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. If you need to connect bare wires to a barrel jack on an Arduino or a development board, this might be the simple solution.

$0.50  
39 pc(s)
This female barrel jack plug is great for adding a common connector to the end of wires. This jack is compatible with 5.5x2.1mm barrel connectors. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.

$0.50  
52 pc(s)
This barrel jack plug is great for adding a common connector to the end of our wires. This jack is compatible with 5.5mm barrel jacks that have a 2.1mm center pole diameter. The outer shell unscrews to reveal solder terminals and a crimp strain relief. The outer shell has strain relief as well.

$0.50  
6 pc(s)
DC power jack / connector. This is a common barrel-type power jack for DC wall supplies. These are compatible with our DC wall supplies and have a 5.5mm jack, with a 2.1mm center pole diameter.

$24.50  
2 pc(s)
The DE-SWADJ is the adjustable version of our SW0XX step down voltage regulators. It is designed to be the easiest possible way to add an adjustable voltage source to a new or existing project with all the efficiency benefits of switch-mode power. The DE-SWADJ is pin-compatible with the...

$42.00  
6 pc(s)
The DE-SWADJ 3 is a larger version of our DE-SWADJ adjustable step down voltage regulator. Previously it was necessary to put multiple DE-SWADJ units in parallel to achieve ratings over 1A, which was bulky, expensive and carried with it a considerable increase in dropout voltage. The...

$14.95  
Out-of-stock
This hand-held crank generator produces up to 15 volts of DC electricity. The integrated PCB includes a full bridge rectifier to provide the same output polarity for either direction the hand crank is turning. In addition, other devices can be easily connected to the screw terminal.
Out-of-stock

$2.50 $3.60  
10 pc(s)
Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an...

$15.95  
Out-of-stock
If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer...
Out-of-stock

$15.00 $16.50  
1 pc(s)
The SparkFun LiPo Charger Plus is the souped-up power option in the SparkFun line of single-cell lithium polymer (LiPo) battery chargers. With this iteration, we've changed the input charge connector to USB-C and provided charge rate selection as well as optional thermal protection. Charge,...

$12.50 $14.75  
2 pc(s)
MOSFETs are awesome. They're like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery supply on and off using your favorite microcontroller. The board also has sewable pads so you can use it in e-textile projects that need more juice....

$36.50  
4 pc(s)
Negatron is a buck-boost converter that takes a positive voltage and turns it into a negative voltage that you can use with amplifier circuits and more. The output is adjustable from -1.3V to -12V. Negatron is also able to step up/step down the magnitude of the voltage. For example,...

$6.50  
1 pc(s)
This single channel Relay Module is specially designed for low-voltage devices and works well with 3.3V power supply. It can be used to control the lighting, electrical and other equipments through the digital IO port. The module comes with on-board back EMF protection to eliminate the...

$22.99  
1 pc(s)
This 16 channels Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. The digital input circuit is optically isolated from the relay, so your controller is protected from voltage spikes and surges. The module is controlled with 5V...

$3.99  
3 pc(s)
This two channels Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. The digital input circuit is optically isolated from the relay, so your controller is protected from voltage spikes and surges. The module is controlled with 5V...

$83.95  
1 pc(s)
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 5 V with an available output current of around 15 A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for...

$85.95  
3 pc(s)
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 9V with an available output current of around 15 A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for...

$16.70  
9 pc(s)
**This battery is not available to ship outside Singapore** This is a very small, extremely lightweight battery based on Lithium Ion chemistry, with the highest energy density currently in production. Each cell outputs a nominal 3.7V at 400mAh! Comes terminated with a standard 2-pin...

$0.95 $1.35  
61 pc(s)
These are general purpose, Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay's coil has switch voltage of 3V at 120mA. The contacts are rated 10A at 120VAC, 10A at 30VDC. Features : 3V DC SPDT...

$0.65  
10 pc(s)
This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm CR2032 coin cells in series to generate 6V nominal. CR2032 tends to have about 220mAh capacity so this holder would give you 6V @ 220mAh with two cells.

$1.99  
Out-of-stock
This Single Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. Applications include solenoid valves, lamps, motors and other high current or high voltage devices. The modules are controlled with 5V signal and they are pre-soldered. A...
Out-of-stock
1 2