Components

1 2
$59.95  
2 pc(s)
Your project may be free-as-in-speech, but that doesn't mean it has to be free-as-in-beer. This handy coin validator/acceptor module is just like the ones you've seen in arcades. This model has the cool ability to accept up to 4 different coins! For example, you can program it for 4...

$18.95  
1 pc(s)
This is a 12 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innards. Commonly, you'd find slip rings in wind turbines, radar antennae, or anything else that requires continuous 360° rotation while maintaining an...

$14.00 $20.00  
4 pc(s)
This is a class 10 64GB microSD memory card, perfect for housing operating systems for single board computers and a multitude of other information. Since this is a class 10 UHS-I microSD it is capable of transferring data at speeds up to 120MB/s allowing it to have a noticeable increase in...

$7.95  
2 pc(s)
This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with any computer, laptop, SBC, etc! Works great with a Raspberry Pi computer, but you can also use it with any other computer you want to record audio on. Simply plug it right in and...

$7.90  
10 pc(s)
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro...

$6.40 $8.00  
2 pc(s)
Don't you hate it when you're in the middle of a build and you don't have a certain value of resistor? Don't let it happen again with this resistor kit. This kit contains a resistor color code chart and 20 each of 30 standard value 1/4 Watts resistors with 1% tolerance. It's perfect for starting...

$4.50 $9.00  
78 pc(s)
This is a 1 GB microSD media card. Perfect for massive datalogging in a minute amount of space. These microSD cards have a simple to use SPI interface allowing any micro to read and write data in a very large 1 gigabyte storage array. This product is guaranteed to work in products that use a...

$4.50  
3 pc(s)
The MCP3008 has a 8-Channel 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply...

$3.95 $7.90  
15 pc(s)
Our new capacitor kit comes with 10 each of 30 different capacitance values. All of these capacitors are packed into the zip-lock bags. This kit provides an easy way to build up a catalog of commonly used capacitors in a way that keeps them organised. Includes : Ceramic...

$3.50  
5 pc(s)
This is an awesome little microSD USB reader. Just slide your microSD card into the inside of the USB connector, then stick this into a USB port and the card's contents will pop up on your computer. Very sneaky - we love it! This little guy is great for pulling data logs off microSD media. This...

$3.50  
38 pc(s)
The MCP3002 has a 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply 2 Channels...

$2.90  
3 pc(s)
This is a small 13mm round passive buzzer that operates around the audible 4kHz range. We drove it directly from a 3v to 5V Arduino or micro:bit to generate simple melody. The buzzer leads are terminated with male pin. Note : This passive buzzer requires a square wave (PWM) signal to...

$2.75  
20 pc(s)
This is the basic LD1117V33 voltage regulator, a low drop positive regulator with a 3.3V fixed output voltage. This fixed regulator provides a great amount of stability and protection for your project and with its on chip trimming this regulator is able to reach an output voltage tolerance...

$1.95  
13 pc(s)
The W25Q64JV (64M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. They are ideal for storing voice, text and data. The device operates on 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. The W25Q64JV array...

$1.70  
5 pc(s)
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...

$0.95 $1.35  
577 pc(s)
There are lots of potentiometer out there. Some are very large, some so small they require a screwdriver. This 10K potentiometer has a small knob built right in and it's breadboard friendly to boot! Perfect for your next LCD contrast adjuster, opamp setting, or volume level. This model # is...

$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...

$0.70  
45 pc(s)
1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 10K resistors make excellent pull-ups, pull-downs, and current limiters.

$0.70  
46 pc(s)
1/4 Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 330Ohm resistors make excellent LED current limiters and are great for general use.

$0.70  
43 pc(s)
1k Ohm, 1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards.

$0.50  
4 pc(s)
This tiny little aluminium heatsink is a perfect solution for cooling off small surface-mount components such as CPUs on Raspberry Pi or stepper motor driver. The heatsink includes thermal adhesive tape for better heat dissipation. The installation is simple, what you need to do is to remove...

$0.50  
10 pc(s)
This is a great looking rubberized knob for the potentiometer. Slides onto the Single Turn Potentiometer and holds tightly with a strong friction fit.

$0.50  
19 pc(s)
2N2222A is designed for high speed switching application at collector current up to 600mA, and feature useful current gain over a wide range of collector current, low leakage currents and low saturation voltage.

$0.50  
677 pc(s)
This BC337 is a drop-in replacement for the 2N2222 Transistor This is the BC337, an NPN silicon BJT (Bipolar Junction Transistor). This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The BC337 is specifically rated...
1 2