Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Components

1 2 3 4
Sort by Popularity
12 Per Page
Heating Pad - 5x10cm
$7.90  
12 pc(s)
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up. These heating pads are constructed using a mesh of Polyester filament and Micro...
− +
Active Buzzer -12mm Continuous Tone
$0.50  
16 pc(s)
This is a small 12mm round active buzzer. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer will switched on by a 3-5V DC voltage. No other...
− +
Potentiometer Knob
$0.50  
10 pc(s)
This is a great looking rubberized knob for the potentiometer. Slides onto the Single Turn Potentiometer and holds tightly with a strong friction fit.
− +
MCP3008 - 8-Channel 10-Bit ADC With SPI Interface
$4.50  
5 pc(s)
The MCP3008 has a 8-Channel 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply...
− +
Mini USB Microphone
$7.95  
2 pc(s)
This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with any computer, laptop, SBC, etc! Works great with a Raspberry Pi computer, but you can also use it with any other computer you want to record audio on. Simply plug it right in and...
− +
Active Piezo Buzzer 3-24VDC Continuous Tone
$1.70  
Out-of-stock
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...
Out-of-stock
MCP3002 - 2-Channel 10-Bit ADC With SPI Interface
$3.50  
39 pc(s)
The MCP3002 has a 10-bit analog to digital converter (ADC) with a simple to use SPI interface. Use this IC if your microcontroller does not have an ADC or have enough ADC lines. A great chip when you need to add additional ADC lines. Features : 2.7V to 5.5V supply 2 Channels...
− +
Thermoelectric Cooler - 40x40mm
$3.90  
3 pc(s)
Thermoelectric coolers (TEC or Peltier) create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. The Thermal Tape listed below works very...
− +
Active Piezo Buzzer 3-24VDC Pulse Tone
$1.70  
5 pc(s)
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...
− +
-50%
Thermally Conductive Adhesive
$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...
− +
Aluminum Heatsink Self-adhesive - 11mmx11mm
$0.50  
8 pc(s)
This tiny little aluminium heatsink is a perfect solution for cooling off small surface-mount components such as CPUs on Raspberry Pi or stepper motor driver. The heatsink includes thermal adhesive tape for better heat dissipation. The installation is simple, what you need to do is to remove...
− +
-50%
3DR Buzzer for PX4 / Pixhawk
$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm
− +
1 2 3 4