Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Components

1 2 3 4
Sort by Price: Low to High
12 Per Page
Resistor 330 Ohm 1/4 Watt PTH (10 pcs)
$0.70  
49 pc(s)
1/4 Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards, these 330Ohm resistors make excellent LED current limiters and are great for general use.
− +
Resistor 1K Ohm 1/4 Watt PTH (10 pcs)
$0.70  
46 pc(s)
1k Ohm, 1/6th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards.
− +
-50%
Thermally Conductive Adhesive
$0.75 $1.50  
20 pc(s)
This thermally conductive adhesive is used widely for heat sinks without fixed fastener, such as on voltage regulator, MOSFET, high power LED and so on. It allows heat to be transferred from IC to the heat sinks, effectively protects IC from thermal impacts, Features : Heat conductivity:...
− +
-30%
Potentiometer 10K with Knob
$0.95 $1.35  
587 pc(s)
There are lots of potentiometer out there. Some are very large, some so small they require a screwdriver. This 10K potentiometer has a small knob built right in and it's breadboard friendly to boot! Perfect for your next LCD contrast adjuster, opamp setting, or volume level. This model # is...
− +
-30%
Relay SPDT Sealed - 3V
$0.95 $1.35  
61 pc(s)
These are general purpose, Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay's coil has switch voltage of 3V at 120mA. The contacts are rated 10A at 120VAC, 10A at 30VDC. Features : 3V DC SPDT...
− +
Active Piezo Buzzer 3-24VDC Continuous Tone
$1.70  
Out-of-stock
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...
Out-of-stock
Active Piezo Buzzer 3-24VDC Pulse Tone
$1.70  
5 pc(s)
Loud sounders that may be powered with a voltage of anywhere from 3.0 to 24VDC. It has additional circuitry in it which makes it easier to use but limits the buzzer to only making one type of a sound (tone). It only requires DC power source for the tone to be generated. This buzzer is...
− +
Split Ferrite Cable Core For RFI / EMI Noise Suppression
$1.80  
3 pc(s)
This easy-to-use split ferrite core provides a cost-effective means to reduce the electromagnetic interference from being induced in or radiated from data and power cables. The special designed plastic housing allows the ferrite sleeve to use with a variety of cable diameters from 3 to 5mm...
− +
W25Q64JVSSIQ SPI Flash - 64MBit (8MByte)
$1.95  
13 pc(s)
The W25Q64JV (64M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power. They are ideal for storing voice, text and data. The device operates on 2.7V to 3.6V power supply with current consumption as low as 1µA for power-down. The W25Q64JV array...
− +
-50%
3DR Buzzer for PX4 / Pixhawk
$2.25 $4.50  
52 pc(s)
This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board. Wire length: ~190mm
− +
Voltage Regulator - 3.3V
$2.75  
20 pc(s)
This is the basic LD1117V33 voltage regulator, a low drop positive regulator with a 3.3V fixed output voltage. This fixed regulator provides a great amount of stability and protection for your project and with its on chip trimming this regulator is able to reach an output voltage tolerance...
− +
Passive Piezo Buzzer w/Leads -13mm
$2.90  
3 pc(s)
This is a small 13mm round passive buzzer that operates around the audible 4kHz range. We drove it directly from a 3v to 5V Arduino or micro:bit to generate simple melody. The buzzer leads are terminated with male pin. Note : This passive buzzer requires a square wave (PWM) signal to...
− +
1 2 3 4