Browse by category

SGBotic Products
Arduino
BBC micro:bit
Raspberry Pi
STEAM
machine learning
Audio / MP3
Breakout Boards
Cables
Camera / Lenses
Components
Development Boards
E-Textiles
Instruments
LED / LCD
Power / Batteries
Programmers
Prototyping
RFID / NFC
Robotics / Hardware
Sensors
Tools
Wireless
School & Uni Packs

Robotics / Hardware

Roboteq
Robot Kits
MakerBeam
Motor Drivers
Motors / Servo
Mounts/Hubs
Others
Shafts
Pulleys and Belts
Pixhawk Autopilot
Wheels
1 2 3 4 5 6 7 8
Sort by Popularity: Low to High
24 Per Page
MakerBeamXL - 500mm Black Anodised (Threaded)
$9.90  
13 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
Vibration Motor Module
$3.25  
16 pc(s)
This small vibratory motor module is perfect for non-audible indicators. Use in any number of applications to indicate to the wearer when a status has changed. The on-board MOSFET driver allows the module to interface directly to microcontroller. Features : Operating voltage:...
− +
TT Gear Motor All-Metal Gearbox - 1:90 Gear Ratio
$7.95  
12 pc(s)
These TT All-Metal Gear Motors are a low cost and reliable way to get your projects moving. They look a lot like our yellow all-plastic gear motors but these have all of the motor gears machined from steel, so they won't strip as easily, and they're twice as slow (and twice as powerful) given...
− +
Mini Lock-style Solenoid - 6VDC
$5.00  
10 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
-50%
Pulley For Toy Motorr - 17mm Diameter
$0.15 $0.30  
8 pc(s)
This plastic pulley can be used to drive wheels or other pulleys with 2mm diameter belt. They have an outer diameter of 17mm and is designed to fit the 2mm shafts and the output shaft on our DC toy motor . Wheel body: ø17 x 4mm
− +
Bi-axial Gear Motor (1:143)
$3.50  
4 pc(s)
This bi-axial gear motor offers a cheap and easy-to-use setup to get your project moving. It possess a 80mm long output on a 3mm diameter hexagon axis. This gear motor requires a voltage of 1.5 to 6V with a no load current of 660mA while possessing a gearbox ratio of 1:134 and a wheel...
− +
Adafruit DC Motor + Stepper FeatherWing Add-on
$36.75  
7 pc(s)
This is the DC Motor + Stepper FeatherWing which will let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors). It features a fully-dedicated PWM driver chip that handles all the motor and speed controls over I2C. Since the FeatherWing only...
− +
Thin White Wheel for TT DC Gearbox Motors - 65mm Diameter
$1.95  
12 pc(s)
This Thin White Wheel For TT Gear Motor is equipped with a rubber tread with excellent traction, and a press-fit design to make connecting super quick and easy. Note : This wheel is only for use with TT gearbox motors . Wheel body: 65 x 18mm
− +
MakerBeamXL - 1000mm Black Anodised (Threaded)
$15.50  
22 pc(s)
MakerBeamXL is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough...
− +
Mini Liquid Pump - Horizontal (2.5V to 5VDC)
$2.95  
Out-of-stock
Looking for a battery powered liquid pump for your Micro:Bit project? This submersible Mini Liquid Pump operates between DC 2.5V to 5V. You can PWM the motor to speed up or slow down the flow rate. Works great with motor driver or a simple relay. This liquid pump does not come with...
Out-of-stock
MakerBeam Hinge Kit
$29.50  
11 pc(s)
1 bag of MakerBeam hinges kit contains 8 hinges and 4 axes (ISO7380, M3, 14mm, A2) and 4 self locking nuts (DIN985).The hinges were specially designed to make a hinge or to mount a beam at any angle you would like.
− +
Mini Vacuum Pump - 6V
$9.99  
5 pc(s)
This mini vacuum pump operates at 6V and has enough suction for most small projects such as blood pressure monitors and automatic machine assembly. Features: Rated Voltage: 6VDC Rated Current: <420mA Inflation Time: <10 S (From 0 to 300 mmHg in a 500CC...
− +
2WD Robot Chassis Kit
$19.80  
1 pc(s)
This 2WD Robot Chassis Kit is easy to assemble and use robot chassis platform. It provides you with everything you need to give your robot a fast two wheel drive platform with plenty of room for expansion to add various sensors and controllers (such as Arduino). All you need to do is...
− +
MakerBeam Bearing
$29.00  
8 pc(s)
Stainless steel bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. If you fit it to a MakerBeam it will extend about 1.5mm from the edge of the beam. The 3mm inner diameter makes is easy to...
− +
-55%
3DR Safety Switch for PX4 / Pixhawk
$4.50 $9.90  
60 pc(s)
3D Robotics Safety Switch for PX4 / Pixhawk is a mandatory component of the Pixhawk autopilot system, allowing you to handle your vehicle safety by disabling the motors until you activate the switch. The safety switch features a three-position DF13 connector to connect directly to the...
− +
Mini Lock-style Solenoid - 12VDC
$5.00  
8 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...
− +
T-Slot Nuts For MakerBeamXL (50pcs)
$17.50  
8 pc(s)
The MakerBeamXL T-slot nut is made of stainless steel and was specially designed to slide into the T-slot grooves of the MakerBeamXL profile. The T-slot nut is great to fasten brackets or corner cubes.
− +
Corner Cube Kit For MakerBeamXL - Black
$25.70  
3 pc(s)
This Corner Cubes can join up to three MakerBeamXL in right angle. Corner Cubes are joined with a beam by the threaded beam ends. Each set contains 12 15mmx15mmx15mm cubes Note : Not compatible with 10mmx10mm MakerBeam.
− +
Timing Pulley - Shaft Mount (20T, 5mm Bore)
$2.50  
3 pc(s)
These shaft-mountable aluminum timing pulleys use 2GT timing belts and attach to a 5mm output shaft with a pair of set screw. They have 20 teeth with a gear pitch of 2mm, an outer diameter of 16mm, a bore of 5mm, and requires a belt width of 6mm. Specification Teeth: 20...
− +
Toy DC Motor Bracket - Metal
$0.20  
9 pc(s)
This compact metal bracket enables convenient mounting of our popular Toy DC Motors . ‎Ø2mm mounting holes. Note: Toy DC motor not included.
− +
600mm MakerBeam Clear Anodised (Threaded)
$9.50  
30 pc(s)
MakerBeam is a Mini-T open-source building system. Mini-T is a miniature version of T-slot (a technology that is widely used for industrial automation, robotics and machine enclosures.) Not only is it small enough to work as a model building system, but it's also precise and strong enough to...
− +
Toy DC Motor Bracket - Plastic
$1.50  
13 pc(s)
This compact plastic bracket enables convenient mounting of our popular Toy DC Motors . Note: Toy DC motor not included. Documents : Dimension drawing
− +
-25%
SparkFun Motor Driver - Dual TB6612FNG (with Headers)
$14.65 $19.55  
8 pc(s)
The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes: CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled,...
− +
3-Blade Nylon Boat Propeller - 40mm Diameter
$2.50  
11 pc(s)
Small fiber reinforced nylon propeller for boat, 3 blades and 40mm in diameter. It push fits directly onto our toy DC motor . Dimensions : Ø40 x 18.5mm Center bore：1.9 mm
− +
1 2 3 4 5 6 7 8