Robotics / Hardware

1 2 3 4 5 6 7 8
$10.40 $13.00  
20 pc(s)
Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil is energized, the slug is pulled into the center of the coil. This makes the solenoid able to pull from one end. This solenoid has a slug...

$2.20  
13 pc(s)
This is a small toy DC motor with a small circular shaft which measures about 9.4mm long. The motor has an operating voltage range of 1.5 to 4.5VDC and a no load speed of 7,500 RPM. It has very low no-load current of 0.09A at 3.0VDC. The motor is pre-soldered with ~200mm male pin lead...

$4.99  
9 pc(s)
This gear motor is designed to operate at low speed of 20rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 0.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm long...

$4.99  
Out-of-stock
This gear motor is designed to operate at extremely low speed of 6rpm at 3V. It can operate up to 6V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...
Out-of-stock

$4.99  
4 pc(s)
This gear motor is designed to operate at extremely low speed of 10rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.5V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about...

$4.99  
3 pc(s)
This gear motor is designed to operate at extremely low speed of 5rpm at 5V. It can operate up to 9V and the rotation can start at voltage as low as 1.8V. Each gear motor sports a 5mm diameter double D-shaft metal output shaft with a M3 threaded hole in the middle. The wire lead is about 12cm...

$11.90  
1 pc(s)
1 bag of approximately 250 pcs M3 nuts. Compatible with all MakerBeam bolts

$29.90  
4 pc(s)
The Magician Rover Chassis v2 is our latest robot platform from Dagu. It features two gearmotors with 65mm wheels and a rear caster. The chassis plates are injection molded with a wide variety of mounting holes for sensors, controllers, power, etc. Simply bolt the two plastic platforms...

Out-of-stock
The MGS1600GY is a sensor capable of detecting and reporting the position of a magnetic field along its horizontal axis. The sensor is intended for line following robotic applications, using a magnetic tape to form a track guide on the floor. The sensor uses advanced signal processing...
Out-of-stock

$14.90  
6 pc(s)
The stainless steel 45 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 45 degree bracket

$14.90  
7 pc(s)
The stainless steel 60 degree bracket is a great addition to MakerBeam product range. Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 60 degree bracket

$29.00  
8 pc(s)
Stainless steel bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. If you fit it to a MakerBeam it will extend about 1.5mm from the edge of the beam. The 3mm inner diameter makes is easy to...

$12.90  
Out-of-stock
The stainless steel corner bracket is a great addition to MakerBeam product range. The corner brackets help strengthen your MakerBeam design. Includes 12x Stainless steel corner bracket
Out-of-stock

$21.50  
2 pc(s)
The corner cubes are designed especially for makerbeams with threaded beam ends. The bag contains: 12x Aluminum corner cubes 50x Stainless steel countersunk bolts with flat head (M3 x 6) 1x Allen key Note : Not compatible with non-threaded MakerBeam.

$24.75  
23 pc(s)
The corner cubes are designed especially for makerbeams with threaded beam ends. The bag contains: 12x Aluminum corner cubes 50x Stainless steel countersunk bolts with flat head (M3 x 6) 1x Allen key Note : Not compatible with non-threaded MakerBeam.

$32.50  
3 pc(s)
Hinge bearing for the MakerBeam aluminum profile. The bearing is 5mm thick. The outside dimension of the bearing is 13mm. The iinside diameter measures 3mm. The 3mm inner diameter makes is easy to mount on a M3 bolt. Trebuchet movement is possible with the added copper saddle band clips,...

$29.50  
11 pc(s)
1 bag of MakerBeam hinges kit contains 8 hinges and 4 axes (ISO7380, M3, 14mm, A2) and 4 self locking nuts (DIN985).The hinges were specially designed to make a hinge or to mount a beam at any angle you would like.

$13.50  
6 pc(s)
The stainless steel corner bracket is a great addition to MakerBeam product range.Each MakerBeam bracket is conveniently engraved with it's angular measurement. Includes 12x Stainless steel 90 degree L-bracket

$7.50  
3 pc(s)
This high quality hex nut driver (5,5mm) is a standard item in our MakerBeam Starter Kit. Work with both standard nuts and Cap nuts.

$15.00  
1 pc(s)
The wing type MakerBeam bolts make it easy to add a bracket midway between brackets already fastened. The rectangular screw head of the wing type bolt gives the possibility to add screws midway. You can insert the screw midway of a beam and turn it to ensure tightening. This way it is easy to...

$7.90  
1 pc(s)
MakerBeam NEMA 17 bracket in stainless steel. Specially designed and made for the MakerBeam product range.

$13.50  
2 pc(s)
The stainless steel right angle bracket is a great addition to MakerBeam product range. The right angle brackets give you the possibilty to place one beam on top of the other. Includes 12x Stainless steel right angle bracket

$7.90  
9 pc(s)
MakerBeam Servo bracket in stainless steel. Specially designed and made for the MakerBeam product range. Documents: Mechanical drawing

$15.00  
8 pc(s)
1 bag of approximately 100 M3 bolts, 12mm - especially made for MakerBeam. The 12 mm bolts have a square head for extra tight fixing, and a hex hole in the head. Length: 12mm.
1 2 3 4 5 6 7 8